Video

Does this work for sulev honda accords?

Thank you so much

So Filling it with water makes it safe. Then just empty it and it’s tea to cut?

I'm trying to figure out if you wire the batteries in series or parallel, are you putting 40 volts or 80?

dude, sick vid, thank you so much for this

If it don't jump uncontrolably out of your hands at least once a minute, you're not doing it right!

This is amazing

How is the wind sound with the open tubing?

I've been wanting to do this FOREVER. So I recently bought a 36v e bike from Amazon, with a smaller 350w motor. It comes with a 7.5ah battery but since it's 36v I can modify it with two 6ah 40v Ryobi batteries

my problem is that is not unplugged but the cable coming out of the motor has to be in a certain position now to work idk why

I have a question, can i fit a awd tranny on my fwd ? My tranny is dead and i can only find awd, but i don't want to make the full conversion, i just need a good transmission. So im wondering if i could buy this awd and install it. Thanks

Good video, thanks. My rear backing plates are about gone, and I was unsure if I would be able to leave the bearing and remove the hub to get to it. It looks like that’s not really possible as I saw in your video - the hub seems to take part of the bearing with it.

Did you ever get the old axle shoulder removed from the old half shaft? If I can’t yank out the axle while on the car I’m planning to remove the half shaft with the bracket and reinstall it once I can get the old axle out of it. It’s a 04 civic hybrid passenger side. I bought an aftermarket axle which I am nervous about as I’ve heard bad things about using them on Hondas.

This lasted me 3 uses or so 😂 the guy at the store said they break easily too.

Did you go with a 36 or 48 volt throttle? I would like to do something similar but I’m confused what volt to use with the 40 volt Ryobi battery

Please learn better language skills. Instead of describing the job in terms of bad, let's use proper language and say something like, "Look at what a fine job this 55 year old piece of equipment has done.'' Also Too mention it's maintenance situation. If it's all original and has been on the job for all or some of those years state it to give credit for it. I have many older things that work nearly perfectly but some have sat out for many many years. Some have been right in the battle year after year and now need a new belt or spindle bearings. It's much more credible and gives a "real '' picture to the listener

Question ⁉️ in a bumpy road , potholes, how is possible not to drop the batteries , they dont get out of place?

Who’s here in 2024

So you made a 40v 12Ah battery kit, how long does it last ? my 48v 13Ah Hailong battery lasts about 36-40km with a 500watts rear hub bafang motor (mostly riding at 30km/h, for a 25km/h avg.)

I wanna do this but I don't know jack shit about electrical or anything. But I've got plenty of ryobi 40v batteries already, would you be willing to show me like how yo make that 2 battery parallel thing u made some time? Cuz that's a great idea

What throttle option did you pick from golden motors?

Not showing my bike. My wires completely different so where do i go then.youtube no help

Can it be used for concrete?

How many ounces of fat should be used for this amount of duck?

I love these things. Especially the water tap directly over the generator head lol.

I had a 800 rpm 6/1 in Texas I ran on waste motor oil at 300 rpm and got 8 hrs to a gallon. After 3 years and 4800 hrs zero carbon on the piston. I ran it through a centrifuge to 5 micron, heated it to remove water and brought acidity down to neutral. Will keep in storage indefinately.

Really nice to know thank you! Has it held up nicely?

How do you open the headlight housing without breaking it?😂

Niceeee

Over do the mixing haaaa

Will this work for an automatic transmission??

So all I need to make my manual FWD into a AWD is the transfer case, driveshaft, diff, rear axles, and all the mounts? Anything else I need to know before I head to the junkyard to pull ll these parts?

Did this rack much much wind noise?

Easy fix, did not notice mine also unplugged and the help doc recommends to directly replace the motor...omg

Good morning my name Javier, you not how to convert automatic 2wd to 4wd. I have honda element 2011 I one to convert 4wd , please help me to do by my self thanks 01,15,24

Second generation Honda CRVs (2001-2006) are extremely similar to the Element, and have the same small battery issue. Thank you for this tutorial! Tired of having to constantly replace my battery every 2-3 years when the winter kills it.

How much

The source of electrical power for our home from 1960 to 2023 in Guyana SA.

this works great for linear polyethylene, but if its crosslinked polyethylene it wont work. OLD TOWN made canoes with both materials, its whatever the supplier sold them so theres not one date where they switched. but newer the boat the greater the chance its linear polyethylene.

Thanks for uploading a solution for error 24. Your explanation was simple and effective. Thanks once again, greatly appreciate it. It worked for me.😊

OK I did this, and I’m wondering what I could’ve broke. I had no code prior after one trip the next day check engine light came on reading P2647 Control unit:09 Status: Confirmed Rocker arm actuator A, bank 1 - actuator stuck on VTEC Oil Pressure Switch Circuit High Voltage The VTEC solenoid is only a year old, I will replace it tonight and put in a new one but I’m concerned that I’ve done irreparable damage. Any thoughts? What could I have broke?

How long is this job doing it this way?

Hi, it’s been a few years. I wonder if you can give me an update on how the gasket is doing ?

Is there a video on awd conversion?

I’m wondering if your canoe repair using #4 plastic bags from about 6 years ago has held up?

I had a model W some years ago. Needed too much work to repair so I let it go. Just for the record, never install a belt while the engine is running.

DO you see any potential problems doing this to an awd automatic?

I cannot say enough good things about your entire video. Optimal 👏👏👏

man you're a "beast", I'm trying to do the same thing and I'm having a hell of a time and thought "i wonder if i can bang it out through the back?" you just showed me it's possible but mine is really rusted but I'm going to sledge the F out of it. i might try cutting the inside with a saws all to weaken it. i need to have both knuckles send out to be sand blasted (because of the rust) and have new bushing to be pressed in. oh BTW my backing plate looks the same as yours

Thank you very mutche