Video

My LCA bracket to frame has been wallowed out by my by tbh bolt being loose.. do you think using this to get the correct orientation for the bolt would suffice? Perhaps get it welded to the frame as well?

Great video! I have a 2002 Taco by the way and it worked the same as video explained.

No difference in Australia

Hi great tool! Your amazon link is broken please update. Thanks!

Thanks, but why didn’t you bleed the brake fluid? I know some people don’t bleed the fluid but you don’t want contamination from the pistons go back up the reservoir.

Something that wasnt mentioned is that a ham license and gmrs licenses aree good for 10 years. But with ham radio you have access to an extremely large amount of bandwidth and massive power limits. But if you are in the offroader class or mountain biking groups you are better served using gmrs.

I have a 2000 F150 truck what floor jack I need( tons) all I need it for is when I get s flat tire or change my brake pads need your advise sos.😅

Thanks. I won a yeti 35 for Christmas. Barely using it for 4th of July. 💥

Who would take a car on that trail.

What set up for 2024 ford ranger wildtrak 4x4. Im planning to upgrade my stocks shocks to BP-51. Do i need to replace the UCA? Thank you.

On a stock lift, will I need to cut them a little? Mine is a Limited, if that makes any difference, 2019.

The holes for the top part didn’t line up because you had it upside down.

I wish there was a map or at least road names. I was thinking about checking it out next week. I'm guessing you went in on Crabtree, do you remember where you came back out to the highway?

285/70 R 17 tires on the 5th Gen. Did you need to do any trim work after the spacers?

Just purchased our son a 1991. Is there a way to clean those covers when removed?

33 what tires 10? 12?

I was looking for a solution to unjamming my winch synthetic cable,watched this video anticipating some cunning tactic, and was very unimpressed when the advice was basically 'pull harder'. But tried anyway, putting my weight into it, and it worked! Sometimes the best advice is the simplest...

Is that box sealed, if I have a snorkel does it work well?

Just meercat it (simples)....... Use a hf radio on cb band 😍😍😍😍 You can talk all round the world on cb radio bands ..... This is just two guys talking trash to make money and promote their classes by telling you cb radio is rubbish compared to ham radio where in reality it isnt .... Cb radio bands rock .... 😍😍😍😍

U have idea for the bump stop for the 1992 hilux?

Wondering why you didn't go with the NSV light bar that is designed to mount inside the plastic hood bulge. I didn't have to cut any metal on the truck, it literally takes the place of the black plastic inset you removed.

I am sorry, but you have so many errors in this video you need to take it down. First, your drawing does not show the actual breakover angle. As others have pointed out, if you look at Wikipedia, you will see the correct drawing and the correct angle. Second, all you math is wrong, and you are basing it off the wrong angle anyway. You have had this misinformation up for 6 years, completely misleading people who come here looking for help, and from your responses below, you have known this for at least 5 years. Please remove it and if you want, redo it correctly.

Does King not make shocks for F150s or any Ford vehicle??? I dont see any videos w said cars

I ordered a 3 inch front and 2 inch rear also and I noticed that the strut spacers are only 1 in a half inches. Is this normal?

This was really the only vid I could find in how to unstick a bound up winch cable. I was janking away at it for some time, took a break, went at it again.... Finally I go for some help here but all the other vids were CRAP. I hooked a chain onto the grapple hook at the end and hung it off the trailer and stood on it with my foot thropugh the chain and BANG !!! BABY !! She came loose ! I couldn't believe it, this worked well - I guess tugging is a lot less force than weight and gravity. THANK YOU 4 years old video dude.

Jimmy, I like your presentation overall; however, according to Toyota, it is not recommended to use the crossmember bar. They say to use the rubber bushing right behind the skid plate. I didn't catch the year of your truck. It may not even be on that year; however, it's in 2012.

Does this mean one side is anticlockwise = lower And the other side is clockwise =lower ?

luv the vid ,, but the music ruins it !!!!!!!!!!

The beds are made of metal, the bedliner is plastic.

Herbie love bug

3rd gen?

Watched your video and dented my crossmember, you should delete this video

Great info, thanks

any issues with light bar long term review???

Thanks

What if i put longer shackles will that help or make it worse?

Are all the bearings the same size for all the pulleys even the small one on the bottom

1inch ball adapter not listed in description.

Read the manual everyone. These ar not the proper jack points.

So it’s 4 years later, does anyone know if the fitting has improved from ADV for these flares?

Thanks for the info, and good presentation as well. Good stuff. My 97 T100 is the first torsion bar suspension I've owned. And the driver side sits a bit lower than the passenger side. This should fix it I believe. Maybe raise both sides a bit while I'm at it.

Very cool. And so smooth

CAUTION!! On the rear install, you have the order of washer/dampeners wrong. It should be the hard-dull washer first, dampener, thin washer (bulge up!), then in the truck bracket - Finish with the other dampener and the other plated thick washer. Otherwise good video.

Can I use my ham radio to listen to CB frequencies I understand it’s not legal to talk from my ham on a CB which is really crappy anyway can I listen?

You answered my question I needed answered to finish my lift! Thanks for the video!

Thank God someone did a good video on this!!

I know this is a few years old now, but are you still running these bars? If so, any wear issues with where they sit on the bed? Thanks!

Works good as long as the puncture is in that big smooth part of the sidewall and not up just a tad in the nobby part...

Love it! That’s about the only thing I want to do to my 4Runner..,

Will these emblems come off ??? I'm worried I'll be driving down the street, and they'll blow off with the wind or something.....