Video

What basic goggles would you recommend for an Autel Evo2

I lost video on my first ready to fly kit, broadcasting 20 Mw. Literally seconds after i switched to acro mode for the first time.I should have disarmed immediately. I panicked and sent it full throttle sideways while blind. Next came an embarassing 1/2 mile trek walking through yards waving a video monotor while the neighbors laughed at me 😂.

Hi, i have a 1300 mah battery and it is rated 30 C. Which means it can provide 39 A of continuous current. But i am using a 50 A esc and my brushless motor only draws 17 Amps maximum. Am i safe to use this setup? and as the esc has higher amp, will it draw 50a from the battery or will it only draw how much current the motor needs (Which is 17A)?

Where did you get your 3d printer from

Ender sucks donkey balls. More time screwing with the thing than actually printing.

Instructions unclear, I bought the $100 dollar kit and am now $7,000 in debt

Cool vidéo, unfortunately you don’t speak much about how many switches, their positions, etc. which could be useful for helicopters or airplanes pilots… for me it’s the definitely zorro and the TX16S mk2, knowing that you don’t need to put 370$ for the tx16S mk2 regular one, coming at 220$. I also prefers the all in 1 able to fly almost anything that the elrs, not so much available and way more expensive than regular receivers, specially if you own many aircrafts…

amazing video no hate

but is it usd or aud

No link for the kit, why?

The thing with the quality parts is also durability and ease of fixing after crashing. Quality gear tends to take a beating a lot better than cheap parts. So in a long run it is better to invest in some good stuff that will last.

The budget goggles are more expensive than my whole drone 💀

and about the ai it might not be programed so good so thats what i belive

bro look at the polaroid 3d printer the camera is so bad and it always fails like all the filament entering he nosel and now im looking for a new one

I hafe the budged drone its awesame BUT the range nahhh💩💩💩💩

thanks for the vid dude ! hoping to but this Ender 3 S1 for my first printer

I, too, am VERY passionate about starting this hobby. I've done a lot of tinkering with both cad sites and the cura slicer, just messin around. I REALLY hope to get my 1st printer very soon, by the end of the fall at the latest! This video definitely has me excited about the S1, praying I get the funds together to get everything I need to get set up! What types of tools would you recommend for this? (outside of the common households ones for assembly)

Stupid didnt even show it printing

Works also on the v2?

Imagine if Meta got DJI...

Dji goggles v2 are out and discontinued😂 bought mine on the ebays😁

Bro can you give a fpv 😊

Wish I watched this before I decided to build a drone😂... Could have been in the air 2 weeks earlier 😢

I was the same but I started out early, things went quite so easy then got 9 printer now lol.

hey, i have had drones before but never a fpv. i have a gopro hero 10, what drone would i need. so do i get a full rig. im on a tight buget.

higher quality fpv video is also more fun :)

Bowden extruder is NOT going to cut for more fancy filament. I did my homework so i knew this upfront before i purchased my first one the Ender 3 S1. Direct extruder is what i want but NOT paying much more. The Ender 3 is truly an amazing deal with what it can do. Thanks to Creality for making 3D printer possible for the large masses of us. I bought a used one and I found out it is NOT that hard or complicated to set up and use. The cool thing is all the stuffs I can print and I can remotely monitor and control anywhere in the world with software add on and a camera. Go for it if you don't do then you will never know and learn. For under $100 you can have one all day long.

Great video, you have made what started out as complex very simple. One of the best instructional videos I have ever seen, hands down.

There is now an option on the Vista for a kit with longer wires.

Thank you very much for taking the time to make this video. It was very helpful!

Where did bro go😂

I regret buying this

I want to get into this so bad. I can’t figure out where to start? I don’t think I want dji.

So can you see clearly though the goggles?

Just clicked on your link and it says they updated to 500mm/s. WOW

yeah avata 2 is cheap :)

excellent video my friend! it helped me a lot.

What do you think of the goggles that come with the emax tiny hawk 3 plus.

I can’t get a plastic bag in NYC but other people get to dump more plastic into our environment? ‘Plastic waste generated from 3D printing is rarely recycled and therefore, will typically end up in landfill’ 🤦🏻‍♂️🤦🏻‍♂️🤦🏻‍♂️

Works for Goggles 2 too please?

Please come back

I like the fact that you talk like a normal person, no high tech mobo-jumbo. Easy to understand and now I feel like I need to go to your channel and see what else I can learn. Thank you

pls be vegan animals also have lifes

brevite camera backpack 220eu absolute joke of a backpack thats worse than 50-80eu backpacks. check out camera, hiking or office backpacks, 30-40L that open like the auline if you want to spend less than a 100. But since this is about expensive fpv backpacks dont be one of those torvol idiots and get a cheaper and better one please

I am with you matt, sometime my grandson stop over and has 2 or 3 hour to fly, So we grab pack and head out. He calls me on his way over dump the batteries on the charge, he livevan 1 1/2=away.

Hi. Thanks for the video. I just did mine. Will it be waterproof after this??

I first researched additive mfg (stereo lithography) back in the 90's. Since then, I've watched the printers get better while reducing the price. When price, quality, filament types and abilities, ease of setup/use merged, I picked up a creality k1c.

Incredible video man, thank you so much! I broke one of the pins on my balance port so I can't plug it anymore, is it okay to charge a lipo battery without connecting the balance port? Thanks !!

Can you give me old Cinewhoop 🥲

Awesome, everything worked. Thanks