Video

am i still be able to drive stock bulbs after doing it? i think so, right?

do you have a schematic, or diagram? I could not find one to save my life! So I started the repair, and I tested the first cap, the 22uf, and it was fine, low ESR of 1.5 ohms. Figured that was good and so I tested the resister, which was 5555ohms, and the bands were green/green/red/gold. So I cleaned the relays and used some deoxit, put it back in the car, nearly didn't make it back out, but still the same fast busy on the left. I have a bunch of caps and stuff ordered because I am going to fix the eff'n seat belt error message, now that I have the proper fuse. Bought 2, just in case. Have you ever repaired the air bag module? thanks for the info and the humor, much needed these days.. :) ps... this is my wifes account, forgot mine..

lol they are supposed to blink slower. the hyper flash is to tell you you have a turn signal bulb out. either your front or rear passenger side bulb was out and you just did some dumb shit lol and it looks to me like now they both don't work

Can I buy one and change it?

I have the exact problem on my 90 Miata. But I'm just going to replace the whole module. I don't have the patience to this sort of job. Lol.

Would this also fix my hazard lights? mine don’t work at all

Awesome tutorial for doing this! I know it’s an older video but do you know what size resistor you could use to stop the hyperblink you get from using led turn signal bulbs?

when replacing R1 would there be any issues if I used a 10k ohm resistor?

did you find a tank to put on yet? the new Isuzu med duty box truck makers made surplus thin 100g thin square Aluminium tanks and I put one on mine they can be had for cheap

I would i like to see before changing them how to test with multimeter at what they are supposed to test at!

As i love my car I hate where they put the fuse and those F***g relays!

This has helped me so much!!! Love your sense of humor!!!! Thank You!!!

I'm a girl...and I'm watching. I want to put a door on my conversion

legends have it he's still tuning the miata to this day

this girl appreciates this very much

Where did you get your sections of frame rail?

"whata gem!" you found!.. thanks for the share! larry

Trey, thank you for showing us your projects! My projects always start while working on another. Endless Adventures !

What type of batteries do you have there? I haven't seen those before...

Whats them name off the two tools you are using to take off and put the valve safety?

Fow everybody who does not fix this problem with 1Mohm resistor, like me, using a 2M ohm one does the trick. If it is a through hole resistor, like 1/4w ones, those can easily be fitted in the original cable making it look stock. --NOTE: No one is going to care or even see that resistor but it's just an excuse to use the resistors laying around the shop without buying smd ones

Did I do something wrong? I have power to my right signal it just doesn’t blink and I put in the resister

Anybody know how to do this on a Mk2.5 ?

@7:30 Damn loud music!!!---TD Steel & aluminum, unless insulated expect corrosion on the aluminum very slowly. The back door looks very good. I am investigating replacing my stock commercial cargo box roll-up rear door with a (possibly remote controlled) garage door. Primary reason: save interior space. Secondary: ease of use. Box width: ~8'ft.

i don’t even care if it wasn’t professional. this guy is hilarious.

Do you have the pin out of this relay

Thanks very much for posting this! Used your steps/info to fix this on my 90 Miata. Cheers!

This video save us! Thank-you!!!!!!! Sharing.

how about the stairs ?

Getting in and out from under the dash...feel your pain. Thanks for the info.

ala lonka.....@14:02 asshat, besides the 15 mistakes made, that is the biggest, may your door leak and rattle forever

Would it be possible to change the resistor out for a trimmer or otger variable resitor? This way you can change the blinking speed on the go??

A metic fuckton haha

I enjoy your humor good sir, carry on.

I know this is old video but just in case anybody reads this..... If you ever stretch frame rails you should always do a Z Notch instead of straight butt weld. Even with fish plates, Z notch is far stronger and less prone to stress fractures.

WHY pollute an otherwise adequate video with so much loud, stupid music. I’m interested in your project and your commentary, but the obnoxious sound has to be squelched, and that means I miss most of what you say. It was great BEFORE you added the sonic desecration.

lmfao great info and better entertainment ! lol

Great video of you talking and pointing at bits you've done. Shame you didn't film the actual job though 🤣🤣

man that is one wobbly video to watch - maybe get a stabiliser or at least run it through some stabilisation software for the handheld to camera bits!

Green seals is for exhaust black for intel

Having a similar problem except one side of my blinker isn’t working and all my fuses are good and light bulbs too thinking of replacing that relay

(insert mind blown imogi here) I've been procrastinating my gear swap but this makes me think I can change out the rears without removing the wheels or hubs. My question is do you think the front axels will come out far enough (until the u-joint bump up against the hub) to change out the front pumpkin?

Have you put it under load yet? I have the exact same motor and need a new generator head, Curious if this worked or not for you

Color me impressed! This summer I was helping my son with his circuits labs... brought back some painful memories here, but it was worth it!

That worked out very well.

"Where's this funny looking 12point nut go?"

That was legit, sick, & dope! Although I really don't like messing with engines, there is a great sense of accomplishment when the $h!t just runs so much better afterwards... makes it all worth while. Fun project you have going there!

CLEAN BURNING COAL

Good thing the brakes work, if you plan to go fast.

Looking forward to speed!