Video

Amazing

Adding lube to the bearing outer is just like adding a thin layer of metal that makes it harder to press in. It depends on the manufacturer. If they don’t ask you to lube the bearing then don’t. It’s they who come up with the tolerances so they will be able to tell you what to do. Don’t just lube the bearing because you think it’s gonna help pull the bearing in. If it’s truly press fit you don’t need lube. The lube will only get in the way.

let's all apply the filler whilst incapacitating the rusted area to ensure its growth.

I'm watching this in awe. I'm gonna attempt to do my own drums. Probably a silly question but do they come with pads for a 09 clio ? Or is that a separate buy. Or do I not need them for the rear brakes

Столько инструментов есть! А рационального мышления нет! Что мешает снять ступицу и спокойно не на коленях поменять?

Great product, sealed my gas fuel gauge on the tiller and lasted for 4yrs now.

Looks like a pain in the ass to use, and the top of the struts pointed at your head.

Paint job on whole car was really poor quality so imagine doing this overt the whole car

This is absolute emergency repair for the broke budget person, it won't last very long, its temp repair. I can do better temp repair with soup can and hose clamps, or better yet get a new flex pipe and put it on, then it will last very long time.

Could this explain no lights, no accessories, switch sounds, etc..?

The robot narrator was so annoying I stopped watching...

Lo hizo hasta llorar 😢

This guy loves to battle , he only had 3 more nuts to remove then the hub would be off and easy to replace bearing ! Work smart bro not hard ! No doubt in my mind that you have lots to learn !

Just remove the driveshaft, put the shaft in a vice. Cut off the old boot and compress/expand the circlip and tap the CV joint off the shaft. Clean up, re-grease and reassemble. Yes you lose a little gearbox oil but it's a lot easier than struggling like this!

😢😢😮👎

another dumbass invention to make money i loved driving in the 70s, life was so easy never heard of a computer in a car and why would you need one anyway

The bottom ball joint is toast

Great vid. Many thanks

Thank you for honest unedited video . Now I know a 6 ton not enough, 12 is on my bucket list.

You guys never needed cheap fix all that stuff cost like 25$ as opposed to a shop

¿Why changing the whole injector and not a simple return valve in each original injector?

Nice one

Do not apply a wax for 3 months after painting. The paint needs to offgas, wax will seal in the paint

Use a transmission funnel and it works exactly the same, for much cheaper.

This is very hard for us the common folk . I always give this to be done by a mechanic, let him struggle

RUBBISH.

Can you tell me where the power steering fluid reservoir is on this car

machanics going to kill you stay safe

Fuck that thing just Rip mine CV boot WTF it FKen Shit

Was going to buy one of these just for this aplication....I see a front-drive bearing replacement on a 20 year old car in my future. So, this demonstrated that I would be better with a 12T press. However, this little press was adequate to carefully remount the new bearing and hub. Removal doesn't have to be that carefully done so long as you don't damage the knuckle.

I’ve always wrench tighten my oil filters on every oil change never had a issue taking them off I would say if they do don’t strip it on the filter don’t over tighten it.

Thank you

the collapse society , homeless mentally illness ,disabled skinny bone addicts poverty weird souls loud speak street dwellers ,pray pray bless.

What do robots know about clear coat? Just say NO to Robots!

Why if bench test ford ranger starter, it not stay ingauge if i keep small wire on pin. It uningage with start small wire on start point. It must only uningage only when i take of start thin wire, am i right or wrong? Rrrrrealy hope someone can help me. Thanks guys.

Looks like garbage

Hot damn the struggle is real. Outstanding video.

Würde den Motor nicht laufen lassen nehme doch ein Heißluftföhn oder lässt du den Motor stunden laufen

pointless cash cow scam products that do nothing, cant beat a manual scrubbing.

Why not fix the back side of the damage areas too. This video doesn't show this. This a waste of time if you only do one side of the damage areas. The rust will come back in those areas again.

why most axel nut seems over tighten and take alot if force when it is only torque to 190 to 240 foot pounds

Wow..... looks much easier to just remove the CV axle and fit a regular CV boot.

Oh dear...This is my sort of effort. I'llneed to watch more videos

What about the snap ring he took off the back u just put one on the front only

😊

6:09 disaster so far... keep watching 6:18 still shite... 6:18 yep noob job...

What's with the robot voice 😂

great video,learned a lot.please more video,s like this. thanx

Пыльник амортизатора поставил старый порваный

Это называется когда проще снять всю стойку