Video

I have the same motor half of my spark plug is clean the other half is black. What does that mean? Also if it’s water, what do I do to fix it?

Show

Maravilhoso professor obrigado pela ajuda.

Sorry my english is bad, I use google translate. How do I know if my Johnson 15 HP 1984 model no. J15 ECTR 1983 needs rings 0386279 RING SET, Standard or 0386280 RING SET, .030 O.S. THANKS

Happens on trucks from road salt in the winter all the time. Use urethan sealer. Bonds to aluminum and contracts and shrinks with the cold and hot well. It’s used to seal windows to aluminum and other stuff like siding. I cover tanks where the bands or straps holding it on. Corrosion always happens between the bank and the rubber grommet.

Great video!

Hi there, thank you for your video. One question, I'm not sure I understood correctly: what's the tightening torque for the four bolts of the impeller housing in Nm (Newton * meter)?

Have you ever heard of the motor over cooling? My 25 hp 1984 evinrude I think my water is by passing the thermostat. The part of the head where the rubber stat seals looks all rough and corroded. The engine never warms up About 107 degrees I tested the thermostat starts to open right at 143 degrees What do think?

Thanks for the video I have 78 evinrude with a bad power head 25 hp how do I rebuild it thank u

I removed the lower gear case from a 2000 8 hp Johnson but the drive shaft is still stuck in the power head. Any suggestions of how to remove it, as it is very stuck?

wow don't know how they come up with this secret code but thank you I'm a 1993

I have a 2 stoke which had a the kill switch issue

Great vid. Thank you.

60 HP e-tec engine will not start unless you unplug the fuel pump wire. then it will start up. Then plug it back in and it will run until you turn it off then it will not start up again until unplug the fuel pump wire. Anyone heard of this happening? I have new injectors, new fuel pump, new lift pump, new coils. all the voltage seam to be right oil pump is working. Anyone got a clue about this.

Nice job!!!!

😂 didn’t know you could move that fast. Thanks for the adjustment lesson ,I used it

Guess it might be high speed clog in the carb ?.? 🤔

Mine idles great smooth. When I twist the handle to half throttle or more drops dead - no fuel even when squeezing the bulb 🤔

Good thanks

Alunimam

Every time I need to tune up my 1977 Johnson 35 hp, I always come searching for this video it's a great walkthrough off all the factors involved in throttle control. A little backstory and then straight and to the point. Thanks OM

Mine was the reverse switch also. Thanks for the help.

I have fixed this problem for my neighbor 2x now. The problem I have found is that using regular fuel line for this repair will make it fail in pretty short order. Most fuel line is not rated for being submerged in gas. The fuel line needs to meet the SAE 30 R10 standard. Most auto parts stores do not stock it, but can order it and have it in store in a day or two. The cost on it is about $20-$30 per foot, but it beats doing this job multiple times. I am about to tear into his for the 3rd time. Hopefully this will be the last.

You didn't show how to adjust the timing..just how to check it

Looks like a gas can spout cap, some one dropped in tank when filling it

Is this using glass or strata glass?

Hi there do the stripped portion of the wire just has to make contact with the coil portion or the clip? And the pin pierces through the wire to contact the wire inside?

So if there is an exhaust leak in that’s system it could possibly cause the engine to overheat?

Some of your information is correct but you putting foam on the inside of your boat does not help the buoyancy Factor at all you added more weight

Best video I've ever seen for this! Thank You So Much! 👍👍 I followed all the step with the re-build kit and got my Jon Boat running perfectly again. It's been a few years now since she's been out and I'm coming back here again to watch before I get to tinkering : )

Thank you.

Got it, removed throttle body and replaced the O-rings, back together and runs no leaks! Thanks for your videos.

Thank you so much! This will help for changing the boots on my John Deere 4020!

Thank you for the good work

Fuel Injectors (What not to do) I have an O-ring gone bad on one of the injectors and I'm having trouble sliding back the throttle body. I did move the fan housing away. Looks like there are 2 nuts holding the body, I removed them. The body isn't budging. Any suggestions?

Can you flush the system without taking everything apart

Does this apply to the 86 25hp johnson as well

Thanks for the info. Was hoping that was my problem. But unfortunately it wasn’t

Thanks OM for the video it was complete an straight to the point 👍🏽

These carbs are a big problem on these looper motors

Thanks for your 6hp video series, i own a 76 4hp and recently picked up a 72 6hp Johnson… got it running today for the first time in who knows how long. I will be going through the carb and ignition also. Thank you for the info

Where does the copper tube under the powerhead go. Does it go in one of the holeds next to the exhaust? Does it go into the hole in the middle in front of the exhaust? Looks like the tube from the water pump goes up there. 1984 johnson 9.9

Thank you for sharing

It's an innovative idea to use wood sticks for the rings. A different way that my dad taught me is to break off one of the old rings and use these pieces to push in the new rings. All ways are good 🙂

Thank you so much for this video series. I have the same outboard and will replace the piston rings. Im currently waiting for rings and gaskets to come. These are the best videos i have seen and you also use regular tools in an outdoor shop demonstrating it can be done.

Powhatan powder and fab, we powder coat them after

Ciao fratello ho un Johnson 15 cv GT del 1989, quando accellero fino a meta' accelleratore va bene, poi a tutto gas sborbotta come va in protezione e non sale di giri.. ha il cdi sotto al volano, cosa puo' essere? lamelle difettose, o anticipo difettoso grazie

Welp this certainly helped. Thank you sir

What's a CU year? E15RCUD ?

replaced the empeller on my 25 evenrude and water is pouring out the exaust but not the pee hole. its overheating too. think its the thermostat. any advice?