- 64
- 925 162
Just Cruzn
United States
Registrace 15. 12. 2015
Hi my name is Rúrik. Im an avid car enthusiast who loves imports (specifically European vehicles). We have a small fleet of vehicle in which we are in the process of either maintaining or restoring. From Porsche and Audi to BMW, I plan to provide helpful how-to's as well as occasional edits of my friends and I as we explore the vast expanse of car culture.
Installing a VDO Continental Radio in a Porsche 944 Turbo
In this video, we run step by step through the process of removing the old Blaupunkt radio, building a wire harness, and installing an VDO Continental TR7412UB - OR radio in a 1986 Porsche 944 Turbo / 951.
Thanks for watching. Like & Subscribe
Link to Porsche Factory Wire Diagram:
www.manualslib.com/manual/392533/Porsche-944-Volume-5-Electrical.html?page=52#manual
Thanks for watching. Like & Subscribe
Link to Porsche Factory Wire Diagram:
www.manualslib.com/manual/392533/Porsche-944-Volume-5-Electrical.html?page=52#manual
zhlédnutí: 1 509
Video
Porsche 986 Boxster NO Start- Replacing the Auto shift linkage / Push Rod
zhlédnutí 975Před rokem
Our 1986 Porsche 986 Boxster 2.5L refused to start after placing it in park and turning the engine off. To our surprise the Automatic transmission shift linkage / Push Rod failed triggering the neutral safety switch and immobilizing the car. After a R&R, we were back on the road. Push Rod Part # 986 426 043 01 Thanks for watching. Subscribe
Trouble Shooting the 928 Ignition System and Air Leaks
zhlédnutí 3,4KPřed rokem
In today's video, we tackle this 1980s 928 S Euro's ignition system. We begin by installing a new distributor cap and rotor, spark plugs, and ignition wire. then we tackle the air leaks and old hoses under the intake manifold. Lastly, we attempt to start the car on ether/ starter fluid. Thanks for watching. Like & Subscribe!
Porsche 928 Compression Test: Low compression
zhlédnutí 784Před rokem
In the last video on the 1980 Porsche 928 S Euro Spec, we sorted some electrical issues and got the engine to crank over. Today we check the compression and overall health of the engine before we proceed with buying parts. Unfortunately, Bank 1 one was substantially lower than Bank 2. This could be a headgasket issue but I suspect the rings are dry from sitting. Fingers crossed the compression ...
BMW X3 M54 Coolant Leak: Removing the Intake Manifold and replacing coolant pipes
zhlédnutí 23KPřed rokem
In today's video, we replace the notorious M54 Coolant lines under the intake manifold on a 2005 BMW X3 3.0 liter. This is a common issue among all M54 straight 6 equip BMW models of the 2000s. This procedure is nearly identical for the E46 3 Series, E85 Z4, E60 5 Series, and E53 X5. This video is intended for reference and entertainment purposes. Please remember to torque each fastener to the ...
928 NO CRANK: Troubleshooting a 1980 Porsche 928 starting system
zhlédnutí 2,1KPřed rokem
Today we are troubleshooting a no crank scenario on a 1980 Porsche 928 S Euro Spec. In this video, I will walk you through the diagnostic process as I attempt to narrow down the reason why this engine will not turn over. Lucky, the issue is surprisingly simple. In the future, we will be trouble shooting the ignition system and fuel system. Thanks for watching. Subscribe. Additional resources: 1...
BMW Z4: Replacing the Headlight Level Sensor
zhlédnutí 3,9KPřed rokem
In this video, we replace the front HID headlight level sensor on this 2004 BMW Z4. It is a very straight forward process and can be completed in 30 minutes. This procedure will apply to all E86 & E86 Z4 models from 2003 to 2008. Thanks for watching. Like & Subscribe
Inspecting a EURO SPEC 928: wiring problems & odd aftermarket parts
zhlédnutí 1,1KPřed rokem
Today we have a customers vehicle in the garage - a 1980 Porsche 928 S Euro Spec import. I recently purchased a parts car so that I can manual swap my 928. The seller was impressed our content and asked that address some of the wiring problems on his 928. In this video, we walk around and tour this beautify yet neglected specimen. I will be tackling the wiring nightmare in a future video. Stay ...
MINI Cooper S R53/R52: Complete Engine / Transmission Removal
zhlédnutí 9KPřed rokem
We recently purchased our newest project vehicle- a 2003 MINI Cooper S with a custom pearlescent blue paint job , manual transmission, and several performance upgrades. Unfortunately the previous owner blew up the engine so in this video we go step by step and show the process of removing the engine and transmission. Stay tuned for the end of the video when the Mini fires back to life with its ...
$600 Porsche 928: Replacing a Trans Cooler Line & Topping Off the ATF
zhlédnutí 807Před rokem
Due to part sourcing issues, Its been several months since we last featured the project 928 on the channel. Thankfully, our new transmission cooler line finally arrived and we are finally able to tackle the transmission fluid leak on the 1984 Porsche 928S. More videos to come soon on the $600 Porsche 928 track car. Transfer pump: www.milwaukeetool.com/Products/Power-Tools/Plumbing-Installation/...
BMW Z4: Replacing the CV Axle Shaft
zhlédnutí 2,3KPřed rokem
In this video, we diagnose a drivetrain issue and determine that the cv axle shaft on the left rear of this 2004 BMW Z4 has been destroyed. This car is heavily modified so it is slightly more challenging removing damaged part and installing the new axle. This procedure will apply to all E86 & E86 Z4 models from 2003 to 2008. Thanks for watching. Like & Subscribe
E60 5 Series : M54 Valve cover gasket replacement
zhlédnutí 9KPřed rokem
Our 2004 BMW 525i has developed a seeping/leaking valve cover gasket. In today’s video, we demonstrate how to properly remove and replace the valve cover & valve cover gasket on an M54 equip BMW 5 series. Thanks for Watching. Like & Subscribe
Installing a Bluetooth Adapter on a BMW Z4 E85/E86
zhlédnutí 30KPřed rokem
In this video, we install a Bluetooth adapter for the stock radio on our 2007 BMW Z4 Coupe. The adapter used in this video was purchased on eBay and we ended up having a few complication with it. I would recommend purchasing an updated/better quality adapter from Amazon (this one worked great in the convertible): www.amazon.com/gp/product/B087JGPJNY/ref=ewc_pr_img_1?smid=A1VA2SYKKAGG47&psc=1 Th...
BMW Z4 (E85/E86) : Removing the rear bumper.
zhlédnutí 5KPřed rokem
In this video, we quickly cover the process of removing the rear bumper on a 2004 BMW Z4 3.0i. This process is the same for any Z4 coupe or convertible built between 2003 and 2008. Thanks for watching. Like & Subscribe
How to remove a BMW E83 X3 Transfer case & Transmission
zhlédnutí 33KPřed rokem
In the following video, I walk the audience through the procedure of removing the transfer case and transmission on a 2007 BMW X3 3.0SI. This process is nearly identical for all E83 models and is similar for the E90 3series and as well as some X5 models. Thanks for watching. Like & Subscribe
Removing the front end of a 1956 Buick Century / Special
zhlédnutí 2,5KPřed rokem
Removing the front end of a 1956 Buick Century / Special
Porsche 951 / 944 Turbo No Start: Diagnosing the fuel system
zhlédnutí 1,1KPřed rokem
Porsche 951 / 944 Turbo No Start: Diagnosing the fuel system
Diagnosing the Buick: What does 40+ Years of neglect do to an engine?
zhlédnutí 950Před rokem
Diagnosing the Buick: What does 40 Years of neglect do to an engine?
$600 Porsche 928: Installing After Market Seats
zhlédnutí 2,8KPřed rokem
$600 Porsche 928: Installing After Market Seats
Everything wrong with my $1200 Buick Century
zhlédnutí 1,7KPřed rokem
Everything wrong with my $1200 Buick Century
The 928 Lives Again: Final touches on the Engine and Test Drive
zhlédnutí 3,1KPřed rokem
The 928 Lives Again: Final touches on the Engine and Test Drive
BMW E30 325I / 325IS: How to replace the Radiator
zhlédnutí 4,4KPřed 2 lety
BMW E30 325I / 325IS: How to replace the Radiator
BMW E30 325I / 325IS: How to replace the Crank Position Sensor
zhlédnutí 11KPřed 2 lety
BMW E30 325I / 325IS: How to replace the Crank Position Sensor
THE 928 RUNS! Engine wiring and exhaust welding on the $600 928 track car
zhlédnutí 1,4KPřed 2 lety
THE 928 RUNS! Engine wiring and exhaust welding on the $600 928 track car
BMW Z4 E85 Oil Pressure Sensor replacement + Oil Change
zhlédnutí 2,6KPřed 2 lety
BMW Z4 E85 Oil Pressure Sensor replacement Oil Change
BMW Z4 COUPE: Diagnosing and Fixing a High Mileage E86
zhlédnutí 5KPřed 2 lety
BMW Z4 COUPE: Diagnosing and Fixing a High Mileage E86
Budget 928 Track Car: S2 Headers, AC delete, and more
zhlédnutí 2,1KPřed 2 lety
Budget 928 Track Car: S2 Headers, AC delete, and more
How to remove the front bumper on a BMW 328i 335i e92 e93 LCI
zhlédnutí 13KPřed 2 lety
How to remove the front bumper on a BMW 328i 335i e92 e93 LCI
E60 5 Series 525i / 528i / 530i engine + transmission install
zhlédnutí 9KPřed 2 lety
E60 5 Series 525i / 528i / 530i engine transmission install
DONT TAKE THE BALL JOINT OFF TAKE THE FENDER LINER OFF >!!
I LOVE YOU JESUS❤
you are a f*cking legend, thank you soo much🫶🏼
Not covering the intake ports was stressing me out lol
Hi. Please How to dismantle the lower front bumper grille?
You do at home..?
Only video i've found for the 3.0 e83, you're the bomb man thanks so much for sharing this!
If just removing transfer case, is it necessary to remove exhaust?
It would be near impossible to access the mounting bolts and drive shaft bolts without taking the exhaust off.
We can’t see what you’re doing, what a waste of watching.
Quality video by the way
Hey man I can get it to start from the pin 14 and the live next to it like in your video. But the key won't crank it. I wonder if the ignition switch is broken. Do you know where I might find some diagrams
I did this exact mod but suddenly it switched to the aux port instead of the cd-port. Sound quality dropped significantly. Any ideas what caused this?
i watched it again. what is the other cable that runs parallel in the housing of the crank sensor cable?
Can you do a video on AC/alternator/power steering belt replacement?
Nice ,not as daunting as I would imagine. Looks just as involved as working on a 1UZFE. minus the spider plenum.
What bumper did you get and from where?
Are you going to share the STL file? Thanks
I need this done in my car and they are trying to charge me 1400 dollars for an hour job, that's insane.
How is Buick coming along
Gonna try this on mine started happening after driving a while and at 63k miles
is this the same process as changing the valve cover gaskets on a 2006 z4 which has an n52 engine?
hey I have a e60 528i and im trying to swap it with a 535i engine is that possible? And would I need different components for the 535i or would the 528i ones fit?
Was doing timing belt on my 1987 BMW 325ic and the CPS wire broke. Gave vin to parts supplier and the replacement CPS has a pigtail at the end and not a plug that goes back into the engine loom. Explained to supplier but had no answer. Thoughts?
Thanks a lot for the info !
what was the problem with the engine of the r53?? mine sounds like that too
How long should the whole job take?
Thanks you so very much. You made it look so simple and easy. You just saved me over $500. Now I feel I can complete this job
How long did the complete removal take
6-8 hours filming. Without the camera I could probably do it in 4 to 5 hours.
Can we fit 525i engine in 530 I
I’m looking at an ‘86 928s which has low compression on one cylinder. From everything I've read, it seems unlikely that the engine would have a lower end issue (only 65k miles). Do you guys agree? If yes, can the heads be removed without pulling the engine?
Are you willing to share the STL?
great video 🤣
That Buick had all the options. 👍
was it really that simple?
I have same module bluetooth, but when connect the adapter, cd changer don t work?! Can you help me with this problem, please ?!
Excellent work I enjoyed it
i have a 328i, im assuming it will fit but does anyone know anything i don't. thank you for any advice
Heck yea dude just enough motivation for me to pull out my old r53 engine n slap a replacement in !!
Comments like these are the reason I make these videos. Thanks buddy!
Does the 3.0i m54 E83 not have a (Non return valve) & Vacuum Control valve?
What is that you have to disconnect from the back of the bumper? Hanging down from both sides actually.
it must be the fog lights id say
Do you have to empty the gas out of the air conditioning
Yes, In his previous video of removing the engine, he makes a note of "evacuating" the refrigerant.
What size tire ?
Where is the installation vidro...Btw, Great video. You made it look so simple Good work Mine, 2005 x3, slipping, hunting, did pass ca smog test...
HERO status for saving a true World Super Car !!
You're a brave and wise person to tackle a true World Class Super car, which is a nightmare to restore !!
In the hands of a good driver, the 928 stands in the Super car realm....IF you can rebuild them and truly DRIVE as designed, all efforts are Worthy !!
Awesome !! You reminded me why i didn't restore a 928 after my 944 !!
Restoring my 944 was a delight; great Material choices, excellent engineering, care seen in every system, "Hot Rod mods" are already built-in. And super efficient at cruising speeds too ;-)
Just ordered one for my '84. What do you suggest I buy for the harness to connect into the vehicle? Or can I run with with comes with the radio? I purchased mine from amazon as well.