Great man! Thanks for showing actual work… getting tired of seeing water tests on CZcams doesn’t show anything but a nice vintage motor running, we’ve all seen motors run. Continue these great videos man!
When I took off the slow idle top one out small aluminum piece stayed on screw the one with the sharp point do I have to seal that back in the carburetor I never had this happen but I only did a couple of carburetors 6 hp
hey I have a 1958 jhonson 10hp out bord that I'm trying to get running good but it seems to be surging at low idle and when I disconnect the fule line there seems to be a bit of water spraying out the air side when it surges aney suggestions ?
Very helpful vid. I am working on a 1961 18hp Evinrude so this was great to see. Can you tell me if backing out the needles is a standard 1.1/2 turns back on both fast and slow?
Close to the same take pictures then you can always see the way it was until I get familiar with stuff I take lots of pictures it helps when you can’t remember like me
I got a 30 hp 1956 Johnson sat in a basement 50 years put coils on and water pump got it running waiting on carb kit can’t find the paint for it it’s called Holliday bronze looking everywhere is there anything close
Charles Kile awesome! Congrats! Glad your figured it out! If you like Brandon’s channel check mine out of you would consider subscribing I’d be grateful!
Great man! Thanks for showing actual work… getting tired of seeing water tests on CZcams doesn’t show anything but a nice vintage motor running, we’ve all seen motors run. Continue these great videos man!
Excellent video thank you very much, my only question is what did you set the bottom high speed adjustment to before you put the knob on. Thank you
When I took off the slow idle top one out small aluminum piece stayed on screw the one with the sharp point do I have to seal that back in the carburetor I never had this happen but I only did a couple of carburetors 6 hp
Thank you for this video know now what to expect with mine. I bought the same motor from my uncle for 50$ isn't in the best shape though
hey I have a 1958 jhonson 10hp out bord that I'm trying to get running good but it seems to be surging at low idle and when I disconnect the fule line there seems to be a bit of water spraying out the air side when it surges aney suggestions ?
Same I have a 1955 15hp evenrude... Same carb😊
You forgot to tell us what the lower needle setting should be for the first start.
Amigo disculpe, cuántas vueltas lleva cada aguja del carburador, tengo un evindure 10 hp pero no se cuantas vueltas llevan las agujas
Very helpful vid. I am working on a 1961 18hp Evinrude so this was great to see. Can you tell me if backing out the needles is a standard 1.1/2 turns back on both fast and slow?
You should count the turns when you disassembled it
@@andyhowat4624 Finely! I have been sitting here for 3 years waiting for the answer! Thanks!
Found the video and photo director app. How do you add live video thumbnails to the main video? Are the directions on the video director?
I'm sorry, what?
could you maybe explain what breaks to cause the propeller to stop spinning. 1957 golden jubilee shifts put won't spin the prop?
Check the shear pin
I have a 57 18hp Johnson Sea Horse, about to rebuild the carb on it, how much different is the process? It seems to be really similar.
Close to the same take pictures then you can always see the way it was until I get familiar with stuff I take lots of pictures it helps when you can’t remember like me
Enjoyed the video! What's the name of that color on the motor? Thanks
Holiday Bronze 58
I got a 30 hp 1956 Johnson sat in a basement 50 years put coils on and water pump got it running waiting on carb kit can’t find the paint for it it’s called Holliday bronze looking everywhere is there anything close
I order from-
www.nymarine.ca/
@@BrandonsGarage thank you and thanks for the videos great info 👍 keep them coming
Hello, do you know, how to adjust High Speed needle? Thank you?
With a screwdriver. 1and1/4 ,turn. The reset when running
I’m working on a 1959 Evinrude 10hp!! So happy you’re doing this project!! Was wondering if you have problems with the new carb kit needle seats!!?
apparently not! every kit i buy the needle seat wont screw in! hmmm also what did you use to polish the needles with??
@@gdamtbnms 0000 steel wool is pretty good for polishing needles and if you want to be fancy, finish with autosol metal polish
Mr. Viceroy thanks!!
Charles Kile if it’s an early fifty’s model, you might need to tighten the outer needle bushing casing screw
Charles Kile awesome! Congrats! Glad your figured it out! If you like Brandon’s channel check mine out of you would consider subscribing I’d be grateful!
Cam follower looks like pain in the *ss to adjust