Video

In case of small tubes such as this, even better solution is to put tape on the place which is cut - spraying water makes a mess and you would need to repeat it several times to make it work. For occasional carbon cutting in my opinion wearing a mask is better - and than it is easy to suck the dry carbon dust.

@@custombikefactory good to know :)

Bardzo mi miło, że podobają Ci się moje filmy. Jest możliwość zbudowania przeze mnie roweru na zamówienie z opcją nagrania materiału. W razie zainteresowania napisz bezpośrednio na e-mail - jest w zakładce o kanale. Jeśli potrzebujesz listy komponentów do samodzielnej budowy, też napisz na maila z informacją o który rower chodzi.

Yes, ninja is spinning bit better, however this is not the most important aspect of BB and not shows how it works under load. Factory could use Ninja BB as default, because they are unable to offer frames with ideal quality en mass.

Thank you ;-)

I am balancing a wheel so it rotates better and do not vibrate. Same thing you do when you replace tires on your car.

A new chain is not greased. It is covered with anti rust substance for storage reason only. This substance is very sticky and attracts dirt, which ruins the chain.

This is lever from ZTTO, Wolftooth should work as well.

Tôi vui vì bạn thích nó. Mọi điều tốt đẹp nhất!

38T/15T

I have not seen any special tool for this and using a punch is the way to go. Between these bearings, there is a loose sleeve with two gaps at the end that allow to apply the punch. Typically these bearings should not be reused after removal so using punch is not an issue.

When I will have a chance, I will try to make such video, as I also not seen one.

I am not expert in batteries so I ordered a custom one, but it was built using standard Samsung 18650 cells and has power of 10,5Ah (504Wh) and runs under 48V. It is enough for a 100km on flat area using 1st level of support, in the hills it drops to 50-60 km.

Thanks and all the best from Poland! ;-)

Thanks, these are 25mm, but on the wide rim, they were 26.5mm. Frame can handle up to 32.

@@custombikefactory thanks for answering! wow they look much wider on camera. also didnt know of rim brakes with such tire clearance! especially available brand new. do you know of any other ? most are 28 only.

@@FedericoHazama nowadays, almost all new road bikes with disc breaks allow up to 30 or even 32mm, it is a trend. On one of my videos you can check how I customized an older rim break road bike to fit 32mm tires.

These are CST Pika 700x38C. Good luck with your project as the frame is ideal for such customization!

Most of this could be done in your trusted local bike shop, but for sure they will not want to customize the engine and firmware. Electric parts can be bought on Chinese e-marketplaces directly or your local online shops, I am sure that specialized sellers will also be able to help with custom software installation.

There are more variables for this calculation, the best way is to do it on the bike, here is official Shimano guide - very simple to follow mtb.shimano.com/stories/determine-chain-length

Yeap, let's hope so!

It is a 3rd hand from my old bike stand - simply a telescopic stick with rubber straps at both ends

With pleasure, just send me such frameset ;-)

Thanks for the comment and good luck with your build!

I believe it is this one derailleurhanger.com/manufacturer/trek/x-caliber2014-20/ - you can also check it with your local Trek reseller

It is definitely not a common practice ;-). I used a thick, thermal resistant, transparent tape. It is commonly used on cars so you can look for it in detailing shops and it comes in a lot of colors too. Choose the thickest one to protect such spots.

@@custombikefactory Oooh, I believe those are called PPFs? The ones that essentially self repair upon heat

I got it from a customer so I cannot share any link, hope your build want all good!

Hmm, to be honest I do not remember any issues when calculating the spoke length for these hubs. Remember there is also rim asymmetry and typically in classic wheel, spokes can be longer/shorter of 1-2mm and still it is possible to get good tension from both sides. This however can vary and I usually go for 1mm shorter than what is being calculated on the web.

Correct, Token Ninja is over 2 times more expensive

Thank you, now i'll know

Thanks!

Naaah, just marketing ;-)

Wooow!!! This is the best motivation I can get ;-))) thank you!! I will try to upload some more stuff, but it is not easy to find the time. All the best and see you in the next videos!

Thanks and stay safe!

ręce które leczą, komentarz taktyczny dla zasięgu xD

Thank you!!

This really depends on a loooot of stuff, very hard to tell, there is also quite some additional work needed to be done apart of pure technical assembly. A skilled mechanic with a good workshop will do it in approx 3-6 hours, so multiply it by a hourly rate and you have some idea of the cost. Often such service might be done as a bonus when you buy parts etc.

Nowadays normal seems something special... thanks for the comment

If your BB is for 24mm spindle than yes.

The CUES crank will work with 9 speed chain, because the internal gap in the 9-11 speed chains are almost the same, it gets tighter from 12 speed, which will be problematic.

Ok, muchas gracias por tu respuesta

...muy útil para configurar mi "Gravel", shifters Sora ST 3000, desviador Sora Fd r3000, cambio alivio Rd m3100 , cassette alivio (11-36)

...a modo de comentario, el factor Q puede llegar a ser un problema sobre todo en las conversiones de bicicletas MTB o híbridas.

You will find all the parts on Chinese portals, but read closely if the set will support your frame (diameters of steerer and frame holes).

You are 100% correct, however even if the wood is not completely straight, it will result in the same measurement error from both sides of the wheel which makes it negligible and acceptable.

@@custombikefactory hehe, that's true! I'm thinking about using a clothes hanger...the design is similar

@@Gledii Hahaha, already tried it, but it is too short ;-)))))

Yes, i just realized after suggesting. I made a very simple version with some scrap stuff I had at home...it did the job

@@Gledii Awesome! My congrats ;-)

Thank you!

Las válvulas de metal pueden hacer ruido en algunas llantas y la cinta las hace silenciosas.

gracias @@custombikefactory

Thanks for sharing your setup and I am super happy it all works well!!

:-) - just like in the description, tools makes it easier, but this is just an inspiration, and you can make it just using a hand saw and a drill, all the best!