- 82
- 788 777
DIY Phil
Thailand
Registrace 9. 01. 2016
Hello. Welcome to my CZcams Channel. I always like making stuff DIY as a past time and hobby. I would like to share with you some of the work I am doing with my motorcycles, home repairs, a lot of other DIY stuff, and my day to day work in Oilfield inspection. I hope you like my videos and please share, like, comment, and subscribe. Thank you very much! Maraming salamat po!
Easy to Make Homemade Powder Coating Gun
This is a very simple yet functional powder coating gun anybody can make at home. I used it with my commercial powder coating power supply, but it will also work from my other homemade power supplies as well.
zhlédnutí: 7 497
Video
Making an Enclosure for Gema Powder Coating Gun Main Board.
zhlédnutí 1,4KPřed 6 měsíci
This video demonstrates how the Powder Coating power supply controls the kV and uA output of the gun. This is a main board of a Gema powder coating gun as seen on Ebay that I repaired, and reverse engineered to show you the circuit schematics. Below are links to 2 previous related videos: Reverse Engineering the Gema Powder Coating Gun Main PCB (Part 1) czcams.com/video/OCLsUD94baU/video.html R...
How To Start a Motorcycle Without a Key
zhlédnutí 1,3KPřed 6 měsíci
3 Methods you can use to start a Honda motorcycle without a key. My bike is a CRF250L but this also works for a lot of other models.
Troubleshooting and Repair of Honda Super Cub FI Motorcycle (Tagalog)
zhlédnutí 282Před 7 měsíci
My wife's motorcycle quit running and the repair shop cannot diagnose the problem with the Honda Super Cub FI fuel injected motorcycle. Simple troubleshooting which applies to all other motorcycle.
Reverse Engineering the Gema Powder Coating Gun Main PCB (Part 2)
zhlédnutí 1,8KPřed 8 měsíci
This is the follow-up video of reverse engineering a commercial powder coating gun main power supply PCB to know how they work. In this video I power up the board and test each functional blocks. Link to video part 1 below: czcams.com/video/OCLsUD94baU/video.html
Reverse Engineering the Gema Powder Coating Gun Main PCB (Part 1)
zhlédnutí 1,4KPřed 8 měsíci
I reverse engineer the main board of a powder coating equipment which was said to be for Gema powder coating gun. I draw the schematic and analyze what each components do. In this video, we will learn how the commercial powder coating gun works. This is a long video and you can jump to specific chapter below at any time. 0:00 Introduction 4:02 Reverse Engineering the PCB 5:52 18 Volts Unregulat...
Motorcycle Brake Caliper Clean Repair and Rebuild Honda CRF250L
zhlédnutí 893Před 8 měsíci
The rear brake of my 10 year old Honda CRF250L motorcycle is having some issues and so I thought now is the time to do a rebuild of the brake caliper. It is an easy 1-hour job anybody can do to their motorcycle.
Homemade Powder Coating Gun vs. Faraday Cage
zhlédnutí 2,2KPřed 11 měsíci
This is a short demonstration of the capability of my homemade powder coating gun to coat a part with "faraday cage" areas. Below links to videos of the homemade powder coating equipment build. Homemade Hopper with Gema Powder Pump czcams.com/video/aoIKBHYMWCQ/video.html Making My Homemade Powder Coating Gun V.4 czcams.com/video/m_fiOeav34s/video.html Homemade Powder Coating Gun High Voltage Ge...
Gema Powder Pump to my Homemade Powder Coating Pump
zhlédnutí 3KPřed 11 měsíci
I added a Gema OptiFlow Powder Pump / Injector to my homemade powder coating gun to finally obtain a consistent flow of powder output. I made a homemade powder hopper to go with the powder pump and a vibrating pad instead of a fluidizing bed.
Making My Homemade Powder Coating Gun V.4
zhlédnutí 3,7KPřed rokem
Another contraption I put together mostly from recycle materials. I made this homemade powder coating gun to have a push button switch trigger tied to a solenoid valve that controls the air flow. This is in-line with my future plan to incorporate a powder pump to feed the gun through a hose from a separate powder hopper. Below links for related videos: High Volage Generator for Powder Coating c...
Powder Coating Gun Power Supply Ignition Coil and TV Flyback Transformer
zhlédnutí 10KPřed rokem
I am trying to improve the performance of my homemade powder coating gun high voltage generator. I experimented with using a motorcycle ignition coil and a CRT TV flyback transformer to be used in conjunction with the high voltage cascade. Below is the link to my first homemade powder coating gun high voltage cascade module: czcams.com/video/jJm6EpnzTnQ/video.html
Modified Yamaha 1997 DT125, YZ Look
zhlédnutí 2,6KPřed rokem
TURN ON CC for English Subtitles In this video, I will explain the modifications I made to this old two-stroke motorcycle. These are the modifications I made to my Yamaha DT125 motorcycle: bore up to 175cc using DTJ175 cylinder CRM250 front and rear wheels CRM250 USD fork XR200 swing arm and rear shock YZ125 (2000) plastic fenders and side panels Other smaller bits and pieces are fabricated usi...
Adding a Solenoid Valve to my Homemade Powder Coating Gun
zhlédnutí 1,3KPřed rokem
Adding a Solenoid Valve to my Homemade Powder Coating Gun
Replacing Motorcycle Chain and Sprocket Honda CRF250L
zhlédnutí 861Před rokem
Replacing Motorcycle Chain and Sprocket Honda CRF250L
Motorcycle Stator Rewinding Honda CRF250L
zhlédnutí 4,7KPřed rokem
Motorcycle Stator Rewinding Honda CRF250L
Repair Motorcycle Charging System Honda CRF250L
zhlédnutí 3,3KPřed rokem
Repair Motorcycle Charging System Honda CRF250L
Motor Assisted Bicycle Prototype Using Weed Eater / Grass Cutter Engine
zhlédnutí 3,2KPřed rokem
Motor Assisted Bicycle Prototype Using Weed Eater / Grass Cutter Engine
Powder Coating Bike Parts - Homemade Powder Coating
zhlédnutí 795Před rokem
Powder Coating Bike Parts - Homemade Powder Coating
Welding on LPG Tank Reused as an Air Compressor Tank
zhlédnutí 3KPřed rokem
Welding on LPG Tank Reused as an Air Compressor Tank
Derrick Bolt Torque Inspection by Rope Access
zhlédnutí 3,5KPřed rokem
Derrick Bolt Torque Inspection by Rope Access
New Powder Hopper Design, Homemade Powder Coating
zhlédnutí 4,4KPřed 2 lety
New Powder Hopper Design, Homemade Powder Coating
Homemade Powder Coating Gun - Nozzle Upgrade
zhlédnutí 9KPřed 2 lety
Homemade Powder Coating Gun - Nozzle Upgrade
Rope Access NDT Working With Overhead Obstruction
zhlédnutí 3,8KPřed 2 lety
Rope Access NDT Working With Overhead Obstruction
Improved Kitchen Oven For Powder Coating Using PID Controller
zhlédnutí 2,9KPřed 2 lety
Improved Kitchen Oven For Powder Coating Using PID Controller
I want a copy of manual service of crf250l
Hi. You can send me an email at philipal2015@gmail.com or message me in Facebook DIY Phil
💪💪💪💪🙏🙏🙏🙏🙏🙏 thanks
Welcome. Thank you too.
Great Bro
Thanks. Hope it helps
Salamat idol
Salamat din po sa panonood at pag subscribe sa ating CZcams channel.
Sir san ka nka bili po ng set ng 175Dtj block and con rod
matagal na kasi yan. nabili ko sa nakilala sa trail taga San Mateo Rizal. Hindi ko alam kung saan nya nakuha.
Savage. I removed one by welding my bike to a tank and driving the tank off the cliff.
Wow. That sounds cool. I hope the bicycle survived that fall.
Beautiful rope to rope transfer
Thank you. The rope-to-rope transfer in this situation is more intimidating than what we did during training because of the height and in open seas, there is also gust of wind.
I couldn’t get my rear sprocket off b4 so I had to grind them off . Then ordered new ones to replace them with the new sprocket
Thanks. Finally, somebody with the same experience. Some commenters think it can be removed without grinding.
where did you get the wire .....
Hi. I got them from online shopping app. Places that repair electric motors will also have them.
Sir ilang mm yung inner ng dt125
Greetings from Japan 🇯🇵, the homeland of Yamaha. Your explanatory video was very helpful. I'm glad that Yamaha's two-stroke engines developed in Japan are still in use in Thailand 🇹🇭. I overhauled an Autolube oil pump, but I encountered a symptom where oil was leaking from the plunger shaft little by little when the engine was running, even though there was nothing wrong with it when the car was stopped. However, your explanation from 4:35 helped me realize that the deterioration of the oil seal on the oil pump output shaft of the clutch cover may have caused the oil in the oil pump to be pressurized by the primary compression pressure leak, causing the oil to leak from the plunger shaft. The oil seal on the plunger shaft is very small and is a springless single lip seal, so it won't leak if you pressurize it by holding the shaft in your mouth and blowing into it, but it seems that it couldn't withstand the primary compression pressure leak of a two-stroke engine. If the clutch cover oil seal is leaking, when adjusting the minimum stroke of the Autolube oil pump, a small amount of oil will leak out from the pulley shaft like bubbles. This is the lesson I learned: when overhauling the oil pump due to an oil leak, it is always better to replace the clutch cover oil seal as well.
Hi @kes7774. You are correct about replacing the clutch cover side oil seal. The Yamaha DT air cooled 2 stroke bike is a wonder of Japanese engineering. It is already discontinued and we cannot buy it new here in South East Asia but I know it is still sold as new bike in Africa. I cannot think of any other two stroke bike model that has been sold for so long time and in many parts of the world as the Yamaha DT.
Can I use simple DC electric supply 4 volt 3 amp with cooking stove module ?
Hi. I am not sure what cooking stove module you have. Can you give more details? There is a high voltage generator on some gas stove that is used to create spark that ignite the gas. If it have DC output then it can potentially supply high voltage electrostatic charge.
You must be re-test UT training. Oke broo👍
thanks for the comment. cheers
Tanung bossing Palit segunyal naba kung mejo loose na yung big pin sa segunyal? Sabi ng nagpress, spotan ko daw ng welding, pero wala paring nangyari, same issue padin nung sinalpak ko
Or may remedy pa ba bossing?
@@johnbenito9019 bago ba yung big pin na kinabit? ang naiisip ko lang na remedyo eh pagkatapos i allign, spotan ng welding yung mismong big pin iwelding doon sa segunyal pero spot lang.
Ok, etry ko nalang e align ulit tas e full weld nalang Kay gin spotan ko yung bigpin sa segunyal pero ganun paren abe
El positivo va a la pistola?
No estoy seguro. Pero debería ser negativo.
Hello Phil, can you send me a wiring diagram of this mosfet board you made in this video.
Hi. You can send me an email at philipal2015@gmail.com or message me at facebook DIY Phil. I'll draw that simple schematic for you.
Music is unbearable. 😮
Lol. Totally agree.
Boss..no need naba mag lagay Ng 2t sa Tanki pag naayus Yan?
Opo. Hindi na kailangang maghalo Ng 2t sa gas tank. Doon lang sa tangke Ng 2T mahlalagay. Yung auto lube pump na nahalang maghalo ng 2t sa gasolina pagpunta sa makina.
You should avoid snapping the hand ascender shut without a rope in. Even a slight damage / burr will start to cut the rope as you slide it.
Thanks for the tip. I developed a bad habit of always doing that.
Na pansin ko yung sa autolob ko is doon sa bandang likod yung tagas ano po kaya problema nya
Malamang po oil seal lng yan.
Sige sir salamat po sa pag sagot
Amazing work man I have same problème
Hello. Good luck fixing your bike.
Nice job mate 🤩🙂
Thanks for watching!
Hi Phil, im Paolo from Italy. I’ve seen your video about powder coating gun , really cool! I would asq an help to you, if possible. I have buyed a onoda ionics powder coating generator, but there is no the gun, i buyed a gun but miss cascade, im looking for a cascade that works with my gun and generator . If i give you pictures of generetor/ gun and electric wire diagram of generator can you try to help me? Thanks a lot
Hi I'll try my best to help. Please send me an email for more details and I'll see what I can do. philipal2015@gmail.com
@@DIYPhil thanks Phil , i have sent you an email.💪💪👍
Not nearly as hard as I thought it'd be. I have a DT 250 and the forks need rebuilt. Thank you, excellent video!
You're welcome!
Osha violatin
yeah. a good vid to show on the next safety meeting
Well done 👏 Thanks
Thank you too!
This was exactly the video I needed. Pretty sure we have the same year bike too. Excellent video!
Glad it was helpful!
Hello po. Pwede ho ba magneto ng dt 125 to Dt 175?...paki sagot idol.. Maraming salamat
Pwede Po.
Thanks
Welcome
Hi sir, can i have a copy of the CRF250L service manual please.
Send me an email at philipal2015@gmail.com. I will reply with the copy of service manual
Sir ano po kaya sukat ng rios na pwede sa by 16 na rim para sa rear stock hub ng dt
GEMA Optiflow type IG06 (copy)
Yes you are right and I got it cheap.
Surely powder coats need to be "baked" after being applied to the surface? How long? What temperature? etc?
Hi. Correct, powdered coated pieces need to be cured in an oven. Duration and temperature depend on the powder used. Have a look at this video with my modified kitchen top oven I use for powder coating. czcams.com/video/d5P7Opt-o2Q/video.html
Is this job only possible with the IRATA certificate? I'm a Rope Technician lvl2 but made my certification in switzerland by the Swiss Mountain Guide Association.
Hi. There is another rope access trade organization called SPRAT so the short answer to your question is no. It really depends on the company and the client. IRATA I think is more common especially in the Oil and Gas sector.
Thank you for your answer. Wish you all the best out there.
😂looks like fun 😂
Thanks very good done
Welcome 👍hope it helps
And sir normal lang po ba na may oil talaga yung sa may stator coil? Sabi kasi ng iba dapat daw hindi basa ng oil ang part na yun
Depende sa motor. Halimbawa Yung Yamaha DT ko walang langis sa stator. Sa CRF impossible na Hindi mabasa Ng langis ang stator kasi naka lubog yun sa langis
Sir can i get a copy of your service manual?
Mag email ka sa akin philipal2015@gmail.com o Kya message sa FB DIY Phil. Send ko sayo
Hints to make it easier: Loosen the front sprocket bolts before raising the rear wheel or breaking the chain. Twist off the larger diameter rear sprocket hex nuts and not the smaller diameter Allen heads.
Hi. Thanks for the useful hints. Regarding twisting the large diameter hex nut, I did that but both hex and Allen heads just rotate. There is thread damage that's why it is stuck.
Are you from the Philippines sir?
Opo
Very good😊
Thank you! Cheers!
Can use mobile repairing power supply
Any adjustable voltage DC power supply should work
How mach power need ignition coil to work plz tell me you have old broad to power but in my country nothing
so good i subscribed. well done, sir.
Awesome, thank you!
hello from usa, very nice work! you have a good brain. i bought my powdercoat gun used and cheap, but you really nailed it. make your own.
Hi Michael. Thanks for subscribing. That I think is the first homemade PC gun I made during idle times at work. I have since made several improvements. The latest one in this video if you want to see: czcams.com/video/aevtL9Id4ms/video.html
does the coil have numbers on it as you have said for conection, how will i know which is the secondary coil?
Hi. This is a step up transformer so the secondary coil has more turns and therefore uses thinner wire. So looking at the wires through the clear epoxy you can see the thinner wires. That's the secondary. Another way is to measure resistance with an ohmmeter. Secondary will have much higher resistance.
Hi Sir, can i ask for a manual? Thank you
Yes of course. Send me an email at philipal2015@gmail.com
Sent Sir using my other email address. TYVM
what the hell it's actually work. It's pretty cheap, I guess only about $30
Yes it does work but not very well. That is the reason I had several improvements to my homemade setup you can find in the homemade powder coating gun playlist in my channel. Thanks for watching and subscribing.
Pare your video is so nice. I will try to follow your guidelines.
Salamat pare and hope it helps.
can you please share the contact detail from where you have bought that kit?
ano po input
12 volts wall adapter po.
kinabitan q 12v sa input pumutok po un dc to dc