ABSURD OR BRILLIANT?! - Turbo 4-Cylinder K-Swapped Porsche 911 Carrera 997
Vložit
- čas přidán 10. 06. 2024
- Tuning By Nick K-Swap Porsche 911 997 Video Playlist: • Porsche 911 K Swap Kit
Continental ExtremeContactSport02 is our Recommended Tire for the Porsche 911: bit.ly/3YwVD1v #SpeedAcademyContinental
Join Our CZcams Community: goo.gl/n4m3Ez
Our Patreon page: / speedacademy
BUY Merch Here: www.speedacademy.shop/
Favorites:
Continental Tire ExtremeContactSport 02: bit.ly/3I4ejyC
Learn how to Tune Vehicles: bit.ly/3toS5iy HP ACADEMY $50 OFF DISCOUNT CODE: SPEED50
$125 OFF ANNEX SUSPENSION use code: 'SPEEDACADEMY' annexsuspension.com/
Swivel LED Light: amzn.to/3kN85Z0
LED Bay Shop Light: amzn.to/2HHBw9D
AirLift Coolant Fill Tool: amzn.to/3FmJlPg
MOTIVE Fluid Transfer Pump: amzn.to/3Fq7lAY
Uvex Face Shield: amzn.to/2jgZttO
Astro Rivnut Tool: amzn.to/2HAZN51
Rivnuts: amzn.to/2Fse0v8
DISCLAIMER:
Speed Academy videos are solely for entertainment purposes. Never perform any modifications to your vehicle that will void your warranty or in any way violate your local road going laws. We assume no liability for property damage or injury as a result of any of the information contained in this video. Use the information provided at your own risk. - Auta a dopravní prostředky
430whp on 11 psi that is so incredible! The K is just so great...
It's a great engine! But I'm still so confused about the swap, especially now that Porsche have had their own flat-four turbo engine for about 5-6 years now if people wanted to swap it into a 911.
A lot of people confuse psi with air flow they are not the same thing pressure is caused by a restriction to flow look how large the intake piping is plus k series heads flow well.
I'm making 600hp on 7psi 🤷♂️
@@TassieLorenzo it's a K-swapped 911, not a homemade 912
@@fishingwithadrian754 exactly why that power level with that boot pressure is impressive, the engine has very good flow
I work at Porsche and I love their vehicles, but I drive a civic Type R FK8. Almost what this build is to me. Best of both worlds. Great job Speed academy in featuring this build and great job Nick on a fine piece of work. Can't wait for my FK8 to get tuned by you. This Build is awesome.
I’m actually cross shopping the two. Haha. I’m leaning towards the fk8.
As a Porsche lover/owner (718 Spyder PDK) whose best friend drives an FK8 Type R I can tell you they are more alike than most people would give them credit for. Seeing this video and many like it I’d love to know if it would be possible to do this swap with a PDK trans to keep that turbo and motor on the boil? I’m an amputee and have access to a 997.1 with a blown motor that has a tiptronic.
@@gouldnj So far, no. But if you have enough money... It might work with the tip though.
Good to see the Porsche swap game getting so much attention. A turbo K in a Cayman (K-man?) would be killer. I put together a LS 911 a few years...I definitely recommend any Porsche swap - 911, boxster, cayman, 944, 928...They're all really good cars and perfect for a K swap!
Damn I think you hit the nail on the head with “k-man”
944 k swap would be nice
Cayman would be lighter good choice
@bgee461 it's a little tall. The hood needs a bump over the valve cover...the audi 07k 5 cylinder fits and it's capable, but it's not developed like the K and there's such a small aftermarket built around that motor that the LS or K are better options imo.
There's a time attack team that ran a K24 for a while in their 944 with a sequential. Black and green car.
I might build a sleeper 924 with a k24 (these names correlate too well) with cams 250+ hp. Pastel colored paint, funky plaid interior... I would daily it. Or a 928 LS daily with a great sound system?
He is making a k-swap kit for Caymans.
Tony Angelo at Stay Tuned is buttoning up an LS swapped 996 C2 (a la Hoovie’s Garage). Gobs of torque, great sound, dead simple. Would be super keen to see K vs LS!
LS for me.
Yeah I immediately thought of Power Kraut too... I'm sure they both drive great but the K sounds terrible, give me the V8 please!
Yeah, absolutely nothing bad to say about this build here. You get beauty, performance, reliability and a turbo. There is also the fact that Nick got to keep the original instruments working using the Syvecs Cpu which is a huge plus. Great video, great car and cheers !
We need a ls vs k swapped 997 back to back comparison .
A great swap that made me think about the ticking timebomb boxer engine in my BRZ. Why is it a great swap? Light weight and well thought out to match the character of the car. Fun episode.
First gen brz? what mode year? i heard that the early FA20s aren’t the best when it comes to reliability.
@@zhila5958 Mine is a 2022 so it would be down the line after it is paid off and can be dedicated to autocross and track. The Boxer 2.4 oiling issues and lack of support by Subaru bugs me.
The K motor is pretty tall. You'd likely have to put a hole in your hood to fit it under there.
@@seabrookmx they fit fine without cutting the hood or subframe, I've had one in my 2015 BRZ for the last two years.
The FA20 has been shown to last around 160k based on the used car market. I know the new ones have that gasket issue but if maintained there’s no reason to consider it a “ticking time bomb” unless you’re driving it like shit.
Can't wait for the Boxster and Cayman version!
Way better than an LS swap
Crazy accurate comment
Not at all..
This was a sick vid. Love these style vids . Speed Academy has some of the best content. Thx guys
I absolutely love Porsche, but I am a JDM guy at heart, this definitely makes sense to me. Best of both worlds for sure
Im not mad. K-Series are simply amazing engines.
My first thought was OMG Ferdinand Porsche is probably turning in his grave.
But when I started watching the video it’s actually make sense.
Yeah he’s wondering why couldn’t make reliable, affordable power 😛
Great video guys! Thanks again for putting it together
Amazing! Finally get to see your opinion of this beast! Such a fun car to drive
What a cool project and so nice to see these type of videos back to the channel 👌
“K” is the way
I would have loved to see you measure it up against a 997-911 turbo for comparison.
When the Cayman kit is ready you guys gotta build one!
Remember the K20 swapped Lotus passing Porches in Nurburgring? Amazing..
In the US the Elises came with a K engine from the factory.
@@quademasters249 Elises never had a Honda K-engine from the factory. Older Elises had ROVER K-engines.
@@Vaino_Hotti I was very specific about US Elises. I know there were no K's in the EU.
You're right though for a different reason, they were Toyota engines. Not K's.
"The 2011 model was the last offered for street legal sale in the United States when the waiver from the United States Government's National Highway Traffic Safety Administration (NHTSA) for Lotus to build and sell cars in the US without smart airbags expired in August 2011.[32] It used the Toyota 2ZZ-GE engine"
Thanks for sharing with us, much appreciation! ❤️
Need a Speed Academy Mid/Rear engine Lap Battle- Turbo K swap porsche vs my NA K swap Lotus ... letssss goooooo
It’s a pricey upfront cost for a project but long term it makes Porsche ownership a little more reasonable for the average person.
Oh amazing! Absolutely love that idea!!
I said this when it was created, it was and shall always remain brilliant.
Great car, good review episode guys!
Awesome swap. Love hearing the familiar sound of a k24z7 in a 911 as an FB6 driver.
Happy you guys got to drive this around. I'm eagerly waiting for his cayman kit.
I love when you do track reviews
finally, the crossover episode, love both channels !!!
Love these track vids!! Can't wait for the nc k swap! ❤
It is nick! I saw the Ontario plate! Your tunes for kseries and edens tuning make the best numbers I’ve seen in NA motors and amazing turns all around. Love your channel
Just freaking awsome 👍🏽
The speed academy I love! Sorry you guys can't get massive views with this content. Btw this is the beautiful thing about about someone agreeing to bring their car to the track for you to test. 10 10th lap time, come on.
I always thought kswap in bmw and porche would be perfect. The power band is suited perfectly for the chassis
This would be my dream car. high revving characteristics and reliable K in a 911.....if I could have one car forever this would capture that idea perfectly
Been waiting on the final follow up of this because I have seen it other places but saw it here first!!
I like the fact that you can maintain lightweightness with the K swap, plus if you blow it up you dont go broke
Brilliant! Once my d17 goes in my 04 civic it’s getting a k24 and going to be a rocket
I love it. I think it’s awesome.
Crazy awesome swapped Porsche K Series Frankenstein car
Peter with all the Jam. Very cool swap Nick!
I don't know... I think I'll pass on the K swapped 911. A huge part of my love for the 997 is the damn motor. From the odd starter noise as the motor cranks over to the boxer 6 howl, it's all too good just to rip out and replace with a K motor. And 997.2 are considerably more reliable. I used to be a huge Honda fan. Then I discovered BMW I-6's and Lexus V8's and I wouldn't touch another Honda 4 banger.
Agree 100%
I have a 911 with the 3.8 motor and it has character.
The stock motors aren’t that unreliable.
IMS problems are limited to early models and not hard to do a preventative fix.
Yep, the Porsche needs that flat 6, even the 2.7 cayman motor is a sweet engine
I love porsche but unless you have a gt3 or possibly a turbo, that engine has huge oiling issues which leads to ims issues and bore scoring. This is simply amazing. People are selling these with blown motors for cheap because a rebuilt or new engine is 20k. This guy figured out what the market needs for these older Porsches. 😎🤟
The build that makes sense! True build for the Speed Academy line of cars. When are you gonna build one??
This is sick!
This is such a killer swap. Sounds good and seems to perform amazingly well. One thing to note about Porsche IMS issues. The aftermarket has completely solved this issue and it’s not much money or labor to get it fixed.
The type of K series this is makes a huge difference in the response and exhaust note, this uses a pretty bottom of the barrel k series with the merged exhaust port cylinder head. In what it sacrifices in efficiency and a much stronger power output it gives a better low and mid range powerband that is better suited for tracks with turns in them instead of mid and top end power that you cant really utilize that isnt a 1/4mi 1/2 or stand mile etc. Not saying its bad but with this K engine I wouldnt push it much past 600whp, the block will take it but the cylinder head is a major choke point unless you do the older k series with the multiport exhaust. Much how like the new "supra" went from a single exhaust port (one for each three cylinders, so two in total) to a multiport in its later revision, the restriction and heat generated with the other style head was a choke point and found to be a cause for concern for anyone wanting to make north of 600whp
This is good news for someone in the middle of this swap on a 996
Way more reliable than the original engine in that car. Great job!
Between this, an LS swap kit, or the 2.7 Audi swap out there now, the options for a more cost effective way to put rollers of a killer chassis back on the road is pretty wide! I think the k 24 would be my jam for this.
Just incredible
K-series
The holy grail
Game changer
this makes me want to boost my 9th gen so much more..... and nick is down the road from me
100% brilliant
Perfect car
Brilliant.
Okay this is great. As a 996 owner I’ve always seen tunning by nicks Porsche and Baysidefabrications k swapped 911 as a great alternative for a track car with a Porsche body
Waiting for the Cayman kit since I've got a TSX which is a super reliable car but not nearly as much fun as my 987.1 Cayman. Almost hoping the engine in the Cayman goes but the base 2.7l is much more reliable than the 3.2 but time with tell.
Excited about his Cayman/Boxster kit he is working on.
As someone with a track S2000 who wouldn't mind having the back seats, stealth, and class of a 911, this really might be the best of both worlds, for roughly the same net cost. Looking forward to hearing more when the kit is completed
K is the way! Sick car and time for build series 😅
This removes the whole 997 engine issues....but K swap... well done gents.
will be looking for the speed academy 997.2 k swap build 👀
Because of the cost to replace really ANY porsche engine, I see nothing wrong with it. I have seen a VR6 Turbo swapped one once and that was really cool.
So in other words, these types of swaps are for people who can't afford the base car for what it is lol
@@Shift4gWhat's wrong with that? People should get the best car they can
@@Shift4g it's not like he has taken a gt3rs and swapped it. You're being a bit purist here. And I love porsche, I love a 911. Hell I loved my 986 boxster that I put on air (you'll hate that too though). If it was my 911, I'd probably drove it until the original engine let go. But of I could make the same power or more with a k swap turbo and be under the cost of a rebuilt OEM Porsche engine, why not?
@@Shift4g If you're going to play the "poor" person argument, then you have to go all the way with it. Why didn't the owners pay double for a 997.2 that won't blow up? Sounds like they can't afford the base car for what it is.
@@Shift4g "what it is", sorry to break it to you but engine rebuilds are not a yearly maintenance item. Porsche knew for a decade about the flaws and did nothing, exploiting their customers.
Yes would love to see a LS 911 vs K swap 911 !
Then Dave vs Peter at the track !!!
IMS Bearing issues are such a small percentage of what breaks on a Porsche motor. It’s such a blown up issue in the Porsche community. Can it happen? Sure. Does it happen on every motor?No. Also, the K-swap is $15k just in parts? He didn’t say what his labor would be. I’d imagine in total, it’s the same price as rebuilding the 911 motor. I think it’s a cool car, but I’d rather rebuild my stock motor, than go with an engine swap from a different manufacturer, because it limits your options on who can actually work on it. IMO
Good points, i think this option is better for ppl who want to buy a cheap dead one and build it from scratch, or go all out with a crazy HP build. Otherwise keeping everything OEM it will be much more servicable
theres more garages used to working on honda motors than Porche ones
thats even worse, idiots be buying up car shells and then swapping them to K without even knowing what the original setup FEELS like... mindless idiot hype beasts@@Pete0126
I agree with you
@@markmartin7384 I agree….but how many shops work on Hondas inside of a Porsche? The fitment, wiring, etc is all different.
This is so much cooler than an ls swap
love it! is there a swap kit or everything is custom fabed?
There will be a full kit. No cutting, no welding. Apparently CZcams doesn't allow website links, but the parts and more info can be found on Nick's site.
Id like to see what people do with the I3 G16 GTE crate motor from the GR Carolla and Yaris
The sound is the killer for me; there is no 4 cylinder that sounds good aside from bike engines. The M96/97 is hardly sacred, but if I'm swapping a 996, it has to be an LS so it at least sounds good. Neither engine will ever touch a Mezger from a sound or emotion perspective, but an LS swapped 996 C2S would be pretty cool if you can't afford a 997. Those headlights will always keep the 996 on the cheaper end of the Porsche tree.
I would love to see what this platform is capable of doing on a 1/4 mile stand point .. I understand that’s not what this was built for but would be interesting to see .
I'm sold. I'd love a honda K20 swap 911. Oh shit and Turo!
This and the Lotus Elise are probably the most compelling options for a K swap.
Nice build. Hope you guys do one for the channel.
2.0ltr subaru wrx sti mate with the porsche twin turbo system .... had to detune to 620 from 980 bhp 😎
Honda i love you ❤
Sickkk
If it fits it fits
I'm gonna K swap my MDX!
Pretty cool way to make it all work.
Personally, if I could choose a 4banger, id do S2K with a sc.
if I was to go turbo, I’d do a 2JZ.
If I could pick any I’d do I’d be looking at LS7/E46/E90 🤘
If you swap a 2JZ into a 911 you'll have the only Porsche with a tail.
Very cool swap, would be great to build the head to rev to the moon. I was wondering what kind of turbo they were running, sounds like G35 but a G25-660 would be great for the track with quick response. Cool to see all the gauges, A/C and traction control. very dialed.
Low rpm boost/power also kills these stock rod k engines
the z7 is perfect for this chassis. the sound is much more fitting than a k24a or k20z
I always liked these Porsches and i like this build. I'm always impressed when everything works as intended🏆🏆🏆
Imagine a 997, with a boosted kswap, and pdk. 😍😍
K series FTW
Nick did you make a kit fornus to k swap Porsche’s? If so I’ll go get this GT2RS it was wrecked but the frame and all is fine and interior is body panels and cosmetics need some love and the motor and transmission are blown, or locked up. But he said he’d take a number for it. And it love to see a K swapped 911 GT2RS. So it’ll be two dream cars making a baby dream car for me
I'd love to own this car
uno de los mejores swap que se le puede hacer aun porsche¡¡ aunque me gustaria ver ese K-series adaptado a una caja de cambios deportiva automatica ya despues de el trabajo de adaptacion no se como no se le ocurrio colocarle a ese chasis 997 una caja de cambios de porsche 718 automatica las de la version 2.0L con las levas en el volante un cambio mas rapido i rascar segundos¡¡
Hell yeah
996 is definitely on the radar somewhere, and this entices the deal if it's going to be a track car!
We are working on 996 support as the mechanical components carry over, just need to finalize and validate the wiring and CAN reverse engineering.
@@williamrori1274 super cool to see, continue the great work!
Love 911s and Honda motors, does it impact the COG the flat 6 gives you?
COG aside, it's WAYYYY lighter which has a larger effect than COG.
Nick: I put a K-series in some place very uncomfortable.
SA: What, like the back of a Volkswagen?
Porsche chassis with a k24 is the beez kneez. Very nice daily driver. For racing I'd recommend no turbo. Go k24-26 built all motor for an ultra light 10000 rpm monster. A 997 GT3.5 RS lol.
The nickel plated cylinders won’t get beat up if it’s kept warm. Cold porsches don’t do well starting and driving in the cold weather. So heated garage and let it get to operating temperature before driving. And those motor last. But that Nicole playing getting scratched, I’ve only seen it on the porsches that are kept in colder climates
Yessssss!!!!!! ❤
I like the concept but the purest won’t accept it. The next thing is when it’s time to change the plugs, it’s an engine out affair, maybe putting the Porsche flat 4 and make a modern 912.
We aren't marketing to the purists. Those are the people that generally don't modify or track their cars anyways.
How do you change the valve cover gasket? Drop the engine?
Great chassis…great engine…it’s a no-brainer
This looks like very reliable fun - and I love a good Honda motor as much as just about anyone - but it’s definitely a bit odd hearing turbo VTEC sounds coming from a Porsche… I also wonder how the on-center to off-center lateral steering feel and handling is affected when directly compared to a stock Carrera with its original flat-six. Supposedly the main inherent benefit of horizontally-opposed engine designs are their reduced “center of gravity”, so I’m wondering if the (heightened) center of gravity can be felt (even just a bit), when approaching or exiting a corner. I would be really curious to examine this before beginning such a comprehensive swap. Also, in this regard, I wonder how a Subaru WRX EJ20 or EJ25 turbo swap/build (i.e. “super beetle”) might compare, even if a bit more expensive, as the engine layout and sound would seem at least a little more natural and intuitive, no?! @speedacademy
Finaly.