How I Installed A New Floor Pan In My 280z
Vložit
- čas přidán 14. 02. 2024
- It's finally the day to weld in the new replacement floor pan on the 1978 Datsun 280z.
Patreon.com/BLOKgarage --- Support the BUILD!
Instagram @BLOKgarage
TikTok @BLOKgarageofficial
#datsun #280z #260z #240z #fairladyz #s30 #build #projectcar #2jz #fabrication #rust
Music by CreatorMix.com - Auta a dopravní prostředky
Man.. watching you is so inspiring!!!
I appreciate the comment a lot!
Lets go, Owen!! He looks a little sus, helping with the seat mounts.
Owen did great.
I saw you were home today and smoke rolling out of the stove pipe in the garage. Thought about stopping in, but didn't want to be the reason for the next video taking longer. Keep up the great work!
Stop in, not going to hurt anything.
Nice job dude I like the way you just didn't overlap the tunnel like most do. Looking forward to more videos. Keep up the good work from 🇨🇮🇨🇮🇨🇮
Thanks! I'd rather spend extra time and make it as good as I personally can rather than get it done a bit quicker.
1st comment! Love the progress next time take the seat runners off and use them to help keep the distance correct. I found with those green panels, on my 510, they are never perfect. I've had to massage them a bit. At least your making progress. That's what counts. Keep it up!
Good call about taking the sliders off. Didn't even think of that. I'll use that on the drivers side.
@@BLOKgarage I'm learning along side you. I'm doing a 510, as I've mentioned before. I've learned to just "k.i.s.s." the sheet metal screws, and square panel clamps have saved my ass several times. Tbh, I've also had to modify a couple of those green panels to fit just right. No biggie though. Keep it up!
Awesome!!
Came across your video and you just earned yourself a follower ! Love the work man I have a 260 Z so I have to do the floors and free rails !
Appreciate it!
I have a roof section to remove a sun roof if you want it. Its not a full roof.
If you have instagram send me a message on there @blokgarage . If not let me know how to contact you. I'm definitely interested.
Nice im tackling this with my crx eventually
Good luck!
@@BLOKgarage thanks!! It's a chore. Never done videos never built a car. I know a little bit about a lot of things. Decided to start a channel with content to document the success or failure of this jswap mini van madness. I was inspired by the rotisserie you were making also.
@@jonathanwickett7028 J swap = v6 it looks like? I'm not a big Honda guy.
@@BLOKgarage yepper. V6. . Purpose built to be heavy, Honda, and blow the doors off vws
seeing those seat mounts makes me wonder if they are meant to be exactly the same positioning as the driver's side? i know that the floorpan shapes and the leg room and such is different from driver to passenger side in these S30s, but maybe that also means the seat mounts are asymmetrical too?
I believe I got them back in the OEM locations, or close to it. To be honest, I wish I hadn't done them at all yet. I think I would have been better off making custom mounts once i figure out what seats I want.
Nice time lapse on that welding 👍how long did it take to weld and grind the whole pan?
The entire floor pan? It was a full weekend. But I don't rush and videoing slowly things down.
Can I use my lincoln mig welder 140 to weld floor pans and what is the best diameter mig wire to use ? THANKS !
I'm not familiar with that welder specifically but looking at it, it should be fine. You don't need much heat to weld sheet metal anyway.
I'm using .030 wire as that's what I already. I've read that .023 wire works best for sheet metal but haven't tried it myself.
Are you using seam sealer on the seat mounts? I had issues where my car leaked and water goes everywhere.
I'll be using seam sealer at least everywhere Nissan had it.