Dude!! This was the most concise video tutorial I've ever seen! Thank you so much. Walked through the steps found the bad relay and my flowing locks are basking in ice cold air once again. Take a virtual beer 🍻 on me homie! You da real MVP!
Thk so much. Brother you help me so much saving me money that I don’t have now. I was almost crying already bc I’m broke. Thank a lot My ac stop working I’m driving Chevy suburban 2008 2500. And the issue was the clutch relay I swapped as you recommended And it work right out Thk Thk Thk
My hvac system wasn’t doing anything at all and I connected two wires to the blower from a drill battery and everything worked fine I couldn’t find the problem though but this video solved my problem thanks a lot my issue was the blower fuse
Great video. Thanks. My blower works, but not getting power to the 10amp fuse under the hood. You touched on that, but any idea why no power it getting to it? If I jumper power to it, the compressor kicks on, so it works.
Hey! What should I try if my AC module seems to be draining my batter when the vehicle is off? When I pulled fuse #42 it stopped the drain on my battery. Any ideas?
quick question, My AC Compressor runs, but only blows soso cool air, it has enough refrigerant, and I can turn it on and off, but it isn't cold enough. I recently changed my radiator, after reconnecting everything, my fans no longer flip on at any moment, ac on or at higher temps. I disconnected the Coolant Temp sensor to keep it running "direct" at all times. (Fans Both run well) Swapped the sensor and the fans won't engage. No codes read on my foxwell cheap-o scanner. Tranny temps are climbing steadily and I'm concerned about the engine temps. Can you help?
We have a 2019 Chevy 3500. Everything is working except when you change from the vents to the floor to the defrost. The lights change on the controls but it won’t switch. Any clue what is wrong there?
Great video brother! I got a 2008 GMC ENVOY the top vents and 4&5 blowers aren't working . My A/C floor and vents are working as well as 1-3 are working not sure of easiest fix? Any tips? Thanks!🙏
I have both fans working and compressor is working as well but I have no air blowing at all. Depending what temperature I set it at. It seems to only engages on when I accelerate.
I have a 2013 GMC Sierra 1500. The blower motor quit and it wasn’t the fuse. I hit a bump it cut out, then later on in the day it came back on. What the issue was is the harness connected to the blower motor was pinched from the factory by the plastic cover. Maybe this can help someone else someday.
Very good video...i have a question my truck does turn on on the inside and compressor you can hear them working except that no air comes out either cold or hot nothing comes out of the vents but again you can hear the compresaor working and the fans but no air comes out of the vents,what could it be???
I have a 2008 chevy duramax. A few months ago I accidentally arced the wire that goes to my intake air heater. Is there a fuse for this on a Lmm? If so, WHERE THE HELL IS IT?
Nice but didn’t quite hit my problem. I have no power to the 10a compressor fuse. Does it get power from the relay? Changed it out but didn’t fix problem. Also what does the ac switch on the dash activate to turn on compressor? Thanks.
i have a 2011 silverado the compressor will not engage i was working 4 days ago fine but need to let you know it was not working correct this summer the compressor would not shut off for 3 months of driving unless you hit the snow flake it colled finein fact tookj to dealership spent 500.00 to get it serviced new freon and all they could not figure out why it ran all the time any was after 2 months it started running like new again. now it got real cold here and it stoped working now its warm again now comp willnot come on any ideas let me know.
while trying to figure out my problem i saw people talk about that issue, they say it is the ambient air temp sensor... it won't allow the AC compressor to engage when it is below a certain temp outside but when the sensor goes bad it can be mistaken on the temp.
I have a 2008 GMC sierra but the AC is blowing cold on one side of the truck which is the passenger side and it’s not cold on the driver side any ideas?
So my a/c works great my problem is why when am towing and my truck starts reaching 240 i mean it cools down but i dont hear my high fan kick on in high speed to prevent going 230 degrees and also to keep my transmission cooled trans runs normal at 180 but when towing it gets up to 220 any advise?
I’m having the same problem, I replaced the blower motor resistor and it worked for a day then everything stopped working again. Did you have any luck fixing the problem?
@@girthbrooks7168 Yea... mine did reset itself too after driving it, i did read somewhere that they do re-learn themselves as long as they are not going bad.
good vid! i disconnected my battery to weld on the fender. after hooking it back up and then running my truck, i only get cold air from ac out of the passenger side and hot air on drivers side. i read that i needed to reset the blend actuator. it called for a removal of a fuse, but i am very unsure which ac fuse needs to be taken out and put back in to do the reset. do you have any idea? Thanks!
Dude!! This was the most concise video tutorial I've ever seen! Thank you so much. Walked through the steps found the bad relay and my flowing locks are basking in ice cold air once again. Take a virtual beer 🍻 on me homie! You da real MVP!
Thanks brother I am glad to have helped
Nice video. Swapping the fog lamp and AC compressor fuses did the trick - at no cost. Thanks man!
checked my AC relay and that was the issue. Thanks!!
Thanks for video no bs straight to the point 👌
Thk so much. Brother you help me so much saving me money that I don’t have now. I was almost crying already bc I’m broke. Thank a lot My ac stop working I’m driving Chevy suburban 2008 2500. And the issue was the clutch relay I swapped as you recommended And it work right out Thk Thk Thk
My hvac system wasn’t doing anything at all and I connected two wires to the blower from a drill battery and everything worked fine I couldn’t find the problem though but this video solved my problem thanks a lot my issue was the blower fuse
Bad ass video man, explained well and showed what needed to be checked. 👍🏻
My fan won’t stop blowing. I might need to just change them all
i love that is GMC/Chevy. i got a chevy 10' fan not working sometimes and then smells really hot
Excellent video man
Great info! Concise and easy to understand! Thanks for making this.
Thanks buddy awesome video
Thank you brother. You helped me.
I checked all fuses u was talking about n the blower motor still not work I even check d blower motor itself it working I put New
Awesome video!
Great video, thank you!
Great video!
Great video. Thanks. My blower works, but not getting power to the 10amp fuse under the hood. You touched on that, but any idea why no power it getting to it? If I jumper power to it, the compressor kicks on, so it works.
Outstanding.
Hey! What should I try if my AC module seems to be draining my batter when the vehicle is off? When I pulled fuse #42 it stopped the drain on my battery. Any ideas?
Perfect
I switched both relayed but it seems that the low speed relay keeps toasting any advice
quick question,
My AC Compressor runs, but only blows soso cool air, it has enough refrigerant, and I can turn it on and off, but it isn't cold enough.
I recently changed my radiator, after reconnecting everything, my fans no longer flip on at any moment, ac on or at higher temps.
I disconnected the Coolant Temp sensor to keep it running "direct" at all times. (Fans Both run well) Swapped the sensor and the fans won't engage.
No codes read on my foxwell cheap-o scanner.
Tranny temps are climbing steadily and I'm concerned about the engine temps.
Can you help?
We have a 2019 Chevy 3500. Everything is working except when you change from the vents to the floor to the defrost. The lights change on the controls but it won’t switch. Any clue what is wrong there?
Great video brother! I got a 2008 GMC ENVOY the top vents and 4&5 blowers aren't working . My A/C floor and vents are working as well as 1-3 are working not sure of easiest fix? Any tips? Thanks!🙏
My ac blower is to slow went I turn on my ac you think I have to change the blower?
I have both fans working and compressor is working as well but I have no air blowing at all. Depending what temperature I set it at. It seems to only engages on when I accelerate.
Same did u fix it
I have a 2013 GMC Sierra 1500. The blower motor quit and it wasn’t the fuse. I hit a bump it cut out, then later on in the day it came back on. What the issue was is the harness connected to the blower motor was pinched from the factory by the plastic cover. Maybe this can help someone else someday.
My a/c clutch fuse isn’t getting any power. Has enough refrigerant and a/c clutch relay and fuse are good.
So im not getting power to the compressor i checked tried all the fuses u sed nd nothing.any help
Very good video...i have a question my truck does turn on on the inside and compressor you can hear them working except that no air comes out either cold or hot nothing comes out of the vents but again you can hear the compresaor working and the fans but no air comes out of the vents,what could it be???
Sounds like an issue with the blower motor.. I'd start by checking for a loose electrical connection and also tapping on the motor
My ac and heater only work when I’m driving would that be a relay or something else else I’m not sure
Air conditioner works on my Sierra but only on high. Thought it was the resistor so I replaced it. Didnt work. I'm stumped
I have a 2008 chevy duramax. A few months ago I accidentally arced the wire that goes to my intake air heater. Is there a fuse for this on a Lmm? If so,
WHERE THE HELL IS IT?
Heated seats won’t even turn on when I try . I can seem to find the fuse location anywhere . Can anyone help?
When I’m driving the fan comes on when I didn’t turn it on
Nice but didn’t quite hit my problem. I have no power to the 10a compressor fuse. Does it get power from the relay? Changed it out but didn’t fix problem. Also what does the ac switch on the dash activate to turn on compressor? Thanks.
Old Gringo Have the same problem man
Have the same problem have you found the solution
Where is the reverse light fuse at
My truck is doing the same thing
How do you remove the 40amp fuses? Seems like they will break when I grab it with my leatherman...
They might.. sometimes the transparent top cover will pop off but thats not a big deal
i have a 2011 silverado the compressor will not engage i was working 4 days ago fine but need to let you know it was not working correct this summer the compressor would not shut off for 3 months of driving unless you hit the snow flake it colled finein fact tookj to dealership spent 500.00 to get it serviced new freon and all they could not figure out why it ran all the time any was after 2 months it started running like new again. now it got real cold here and it stoped working now its warm again now comp willnot come on any ideas let me know.
while trying to figure out my problem i saw people talk about that issue, they say it is the ambient air temp sensor... it won't allow the AC compressor to engage when it is below a certain temp outside but when the sensor goes bad it can be mistaken on the temp.
How do I get ahold of you?
I have a 2008 GMC sierra but the AC is blowing cold on one side of the truck which is the passenger side and it’s not cold on the driver side any ideas?
I’m having. The same problem
Awesome Video👍
So my a/c works great my problem is why when am towing and my truck starts reaching 240 i mean it cools down but i dont hear my high fan kick on in high speed to prevent going 230 degrees and also to keep my transmission cooled trans runs normal at 180 but when towing it gets up to 220 any advise?
Did you ever figure out you problem?
No i just went and bought a duramax for towing i tow every other day 10klbs so def needed a diferent truck
The AC panel control doesn't have lights it's not working not all Teresa fuses for that
what about the one under the glovebox? the one on top of the evaporator housing?
I’d like to know what this one is?
@@codymcconnell1231 they told me at AUTO ZONE that there was one in bacl of the glovebox
My system turns on but it doesn’t blow any air
I’m having the same problem, I replaced the blower motor resistor and it worked for a day then everything stopped working again. Did you have any luck fixing the problem?
Ted Williams
So my Battery died and after I boosted it the driver side is blowing hot air and the passenger side is blowing cold. any ideas?
did you figure your problem out? mine did the same thing
@@mikecochrane2074 Hey so after about a day and a half it reset everything on its own i am not sure how.
@@girthbrooks7168 Yea... mine did reset itself too after driving it, i did read somewhere that they do re-learn themselves as long as they are not going bad.
I have AC and no heat
What if you get 3 flashing lights when you try and turn it on ac?
Check for leaks might not have any more refrigerant.
I get the same 3 flashing lights any ideas refrigerant is full .
good vid! i disconnected my battery to weld on the fender. after hooking it back up and then running my truck, i only get cold air from ac out of the passenger side and hot air on drivers side. i read that i needed to reset the blend actuator. it called for a removal of a fuse, but i am very unsure which ac fuse needs to be taken out and put back in to do the reset. do you have any idea? Thanks!
2008 gmc sierra, just like yours