Video

Yes, if it was mine I would have a sequoia table mount on the floor with a removable post so we could have a little table. With regards to the seat removal. You could remove the rear and left hand bench part without too much trouble/time, the right hand bench wouldn't be removable in this particular build as all the electrical component and leisure battery are installed in that location. It's all done to the customers build spec and everyone is different and required different uses which is the great things about these builds!

@@VanCreations Hi, Thanks, yes after this video I watched another one of yours with centre seat removal which is great. I love the 240 hook up under rear light. Fantastic. Any where we don’t need to drill holes in van is a great idea. 👍🏆

Hi Eddie, Fitting a bench triple in the middle row requires the larger type brackets. The smaller L shape brackets are used on the far outside brackets of a 2+1.

Hi, Yes you could install 240v or 12v sockets along the back as there is plenty of room for them! Simon, Van Creations

Thanks! I hope this helped explain the install. We try out best to make it as easy as it can be! Good luck! Simon - Van Creations

Yeah, unfortunately but that's motoring for you!

No we don't. Same as the VW factory built Kombi's. We do treat any bare metal from drilling with primer/sealer. You could put a bit of sealant around the holes prior to the brackets going in but we've never seen any water ingress from this area in retro fitted or factory Kombi's.

Great point! Thanks for the feedback! Many Thanks, Simon

Merhaba, Bunları ülkenize gönderip gönderemeyeceklerini öğrenmek için TransporterHQ ile iletişime geçmeyi deneyin. Saygılarımla Simon

Hi, I believe they are available in LHD, Your would need to contact TransporterHQ and ask. Regards Simon

Hi Chris, Your rotate the passenger seat and then can step up on the seat and boost yourself into the roof bed. It's not too difficult to do. Regards Simon

Go for it if your can. Nice to be able to use for days out or weekends/weeks away. We use ours more for days out than camping but its so handy to randomly stop at a beach on the way home and have food and drink whilst watching the sunset. Regards Simon

The new ones are Aftermarket lamps from TransporterHQ. These are the V3 LED Headlights.

Hi, 4.8 x 16mm or 5.0 x 16mm will be fine. Simon

@@VanCreations Thanks Simon. I have 4.8 x 14mm stainless steel rivets. These should be fine!

Hi, You can relocate the aerial to the inside near the pillar or install a DAB aerial. You can also buy a relocation kit. Simon - VC

Hi, No error codes with the THQ bulbs. Simon

Hi, You will need to speak to where you purchased your bars from. Usually side bars come with the fitting kits from the manufacturers.

Hi Thanks for your comment. After installing the headlights, you can park your van face on from a wall/fence etc.. Depending on the position of the bulb, you can sometimes cast a shadow(black spot) where you would want a clean light pattern. If you reach behind the headlamp to the back of the bulb you can rotate it slightly and watch on your wall the shadow move out of eye line. You are trying to create the cleanest beam pattern you can for the best vision at night. It's a little bit tricky to explain but I hope this helps. Next time we install these headlights, I will see if we can do a video on the set up! Cheers Simon

Hi Chris, This is 60mm Ducting for heater inlet and outlet. On the bigger heaters you can use a 90mm Ducting. Many Thanks Simon

Hi James, You wouldn't be able to have UK seating the other way round as the seat belt receptacle and levers on the single seat would be on the wrong side and the seat is offset so I can't see that working. Also the belt and receptacle on the double would also be wrong. Best Regards Simon

What about 3 single seats ? Is that an option? Thanks

Hi Steven, The van in this video is a non 4Motion. This one was running 245/65/17 with no issues. Just go careful not to go too big or too wide with the AT Tyres as problems can occur when moving into 18” or bigger.

This is a good point, The heater unit and ducting is protected by the under trays (once refitted). The unit and ducting sits higher than the vans control arms and table so you would bottom out on these first BUT if you're often using your van off road or through floods then we would highly recommend to have an internal heater install.

Hi Gareth, We're based in Dorchester, Dorset.

You're welcome!

Hi, To complete the 2+1 seating you will need 4 x Small LH Brackets 4 x Small RH Brackets 4 x Large (double width) Brackets 2 x C-Pillar Brackets (For Seat Belts) 8 x Kombi Seat Floor Brackets (for inside the van) 16 x Nuts 2 x Seat Belts 8 x Floor Bracket Covers 2+1 Seats If you're struggling to source them, please send us an email and we can send over a quote for supply only of the under chassis brackets etc.. Simon

Feel free to contact us on our email address and we can give you a full quote depending on your van spec/setup. Campers@vancreations.co.uk

and longer depending on the furniture and where the battery has been installed. We've had some in where the battery has been built into the furniture with no access to it unless you start taking the furniture out! Everyday can bring a surprise!

Bloody he'll mate how do u chathe to fit I have one just need fitting pal

Thanks, appreciate the feedback. Been there and done that, laying on my back out in the rain trying to fit side bars. Actually, When we started many years ago our ramp wouldn't fit LWB vans on so all LWB ones where done on the ground outside. Luckily we moved into our newly built workshop back in 2019 and have the 5ton extra wide ramp for commercials.

Thanks!

Hi John, I’m not in the shop today but I’m sure it’s 8mm threaded bar. I cut them to around 450mm length to allow us to drop the tank and leave it in position whilst we install brackets, diesel heating and other mods! Saves us having to remove completely and free’s up our gearbox jack. Simon

Hi John, I’ve just been in the workshop and measured today, it’s M8 bar. I’ve updated my other response.

Thanks

No problem 👍 I hope it helps!

How did you get this?

@CZcams it’s coming shortly!!

Hi Karl, We charge £300 labour plus parts. Parts vary as some customers already supply brackets etc..

@@VanCreationshave you got a number to call?

01305 250691 or visit our website for email etc… Many Thanks, Simon

Sorry, but boring without background music and we have to be careful as to what we use due to copyright! Thanks for the feedback! Simon

Problem with just bonding is we have seen many spoilers bonded on by others and they have come off! We have one in the workshop at the moment that needs re-bonding as it probably wasn’t prepped properly or the correct primer applied!

Will be coming out hopefully this week, apologies, we’ve been super busy in the workshop and no time for editing just yet!

Thanks, I'm wouldn't know to be honest as we only install genuine VW Belts. The genuine belts are designed to go in this location and the spools have the correct mounting bracket to install in the vans bodywork. (there is a notch out for it to sit level). I would recommend factory bell and reinforcement plates only!

@@VanCreations thanks for your reply. Have ordered genuine VW. What is the measurements for the c pillar plate. I have a swb single side door. Hope you can help

Also you said the seat belts are sided. How do I tell?

255mm down from the ceiling line, it’s in the video when I set up the laser to demonstrate!

easiest way is to google the part number on your belt retractor unit and it will state left or right!