Video

V3 fake ebay does not charge

Acetone, hydrogen peroxide, and acid. Make sure to avoid buying all the chemicals at once guys!

Great video, thanks a million for your time making it, very simple to understand and practical.

Your kidding. ,,I don't have all that equipment . Does my work or not. ? Thats what I need to know . Not a math lesson. You didn't tell me what set my meter too...?

Wait, ,,,what ?

Everytime I find a decent channel that's interesting and they explain stuff simply for everyone to understand, they have fallen off the earth. Man hasn't posted a video for 3 years 😮

why do you need battery for this?

Easier to just use positive resist , usually even better than toner trasfer as well

I bought this little gem off of Facebook marketplace with two speakers and a woofer for only $50 and it sounds great!

I bought a universal charger. 2 contacts on charger and 3 on battery like yours. What is that middle contact on battery for and can I possibly have battery in reversed??

Good video to explain many things. But for LED I'd recommend to implement simple ConstantCurrent self-oscillating buck using comparator LM393 it's faster than OPAMP. Using 2 SMD BJTs and 1 N-MOSFET still could be cheaper than using specialized IC, simpler but of course less to explain :)

私は７番ピンのＶＥＥに０Ｖを接続しても問題ないか情報を探していました。動いてますね👍

Done, i did it and it works!!

You have, without exaggeration, the best tutorial on DIY PCB creation. You make it look super easy, which is a bit off putting. Just means you’re doing something right. Thanks for all the time and effort you’ve put into this video, it is greatly appreciated. I look forward to seeing what else is available on your channel. Thanks again!!!

There are 4 kinds pipo siso piso and sipo

Great result, much thanks for sharing. Excellent use of lateral thinking!

Thanks a lot for the video! After 7 years still very helpful

Is the pen drive a software for the machine or communication?

Super video. Tak 😃

Thank you! Very easy to understand and helpful <3

Is there any auto cutoff feature in it

Just got it for 8$ and it's in good condition only needed some dirt cleaning. But I still like my G600, sadly it's laser died for no reason

Hello friend, do you have any Arduino code for a 7-segment clock with this register? Thanks

You that fake charger has setting for lithium ion battery..that no gonna work if you charge it with lipo setting.find li-ion setting..

If sound does not produce and it writened "PCM" problem what is needed to do with?

Tx, surely that laser requires a heat sink, its just a naked diode and will probably burn out after 20 minutes continuous use or less, you would be in my opinion much better off using a cross hair laser and use that in combination with Laser Pointer Offset control in Lightburn and it will allow you to place the laser exactly in the right position without having to try and manually line it up with the mount etc. Its much easier and its 100% accurate everytime. Its not so bad for me as my tube as the laser screwed on to the end of it but by the time it goes through the mirrors the red dot it more like a ghost of a dot as you l9ose so much of the brightness that way so I am looking to install an additional red dot which is where I came upon yours. tx.

19:55

23:57 invert signals

52:00 final results

43:07

Hello Brother. Today I met your channel. With a quick look at the videos you made, of course, I only looked at the type of things you did to see your videos later. You got a big like for the hard work you have done and continue to do. I have good wishes for you. Always be healthy and happy and successful. Yours sincerely

may you share your code please?

Nic ❤

What will happen if you keep the toner as a protective layer ?

The ink tank system appears to be much better than the cartridge system czcams.com/users/postUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 and a lot cheaper to run. The machine was easy to set up. A small point but I thought they'd be a USB cable included to help with the set up but there was none. I've been using it now for a few weeks and it seems like a good product and superior to my previous printers which were all troublesome HP machines.

I got the 980D. I wish I would of got a amazon Yihua so I could get a desolder iron and a reflow gun attachments

Woah, rotary switch. Cool.

🎉

Iwant this avr displayic boad

Please I can't access your arduino code on the robot car.

Why don't you just use Timer 1 for 16 bit PWM output.

It work for Leds not light bulbs!!

Thanks alot for the Video. I am now looking for new switches and repair my mouse in the same way. I tried the new G502, but prefer my old, so i will do my best.

Just did this on 2 mice. The header bank was super easy to desolder if you hit it with a bunch of flux and some leaded solder. It wicks right up. good luck!

You HAVE to calibrate it. They usually don't at the factory.

This simple video actually taught me a few things. I never thought of a piezoelectric speaker as a crystal and now I understand how the oscillator for an Arduino works. Thanks. Great video.

Hello sir

Making use of the czcams.com/users/postUgkxcJ22tnHH9l1vjdIdEIG27iOG55P7LXI8 reconditioning plan, I just saved 2 auto batteries from being completely junked. The guides were very simple to follow. I wish I would have found this years ago! You may use the guide to recondition any battery type

For a 20$ charger it done the job I use mine over a year chargering 2'3'&4s lipo battery's I was new to rc's since then I've learned more an moved on to a smart charger & battery set up but I got my money worth out of it believe me ....

Thanks a lot !!! I was really lost with this machine and you really illuminate me !!