Signal reflections and Transmission lines - Ec-Projects
Vložit
- čas přidán 7. 07. 2024
- "Quick" introduction to signal reflections! A few things I forgot to mention, that I noticed when I edited the video. This is a big topic for PCB design as well! Especially at higher frequencies. And the same techniques apply. For systems where you use the same wires for RX/TX you would put the parallel termination in both ends of the cable (RS485, CAN, etc ).
¤¤¤¤ -- SUPPORT Ec-Projects -- ¤¤¤¤
By using my Amazon affiliate links (No extra cost for you!)
Amazon US - amzn.to/1kNT3RM
Amazon UK - amzn.to/1OnZ2aX
Amazon DE - amzn.to/1Vt6zqg
By becoming a Patreon for as little as $1 per month
Patreon - / ecprojects
¤¤¤¤ ----------------------------------------- ¤¤¤¤ - Věda a technologie
FIRST!
A few things I forgot to mention, that I noticed when I edited the video. This is a big topic for PCB design as well! Especially at higher frequencies - and the same techniques apply. Your bare board PCB manufacture will happily, for a big bag of money, make your PCBs at a specified impedance (+/- some tolerance). You still need to keep the correct trace width and spacing to the ground plane though.
For systems where you use the same wires for RX/TX you would put the parallel termination in both ends of the cable (RS485, CAN, etc ).
Really great and easy to understand video of the importance of current loop impedance and signal integrity for PCB layout considerations. All this has a huge impact on radiated and conducted EMC too, which for a commercial product is an essential consideration!
Fantastic demonstration of transmission Lines
Nice demo. I attended a 4 day course on the practical considerations for this - what a long 4 days...
Thanks. Yeah, I could imagine :)
Fantastic demo, simple and practical. Thank you
Talk about perfect timing, I was just studying signal reflections in a PLC class today. Damn interesting
Very well explained ! Thanks for sharing !
Excellent video! Thanks!
Good demonstration ! 👍
Pretty good reflection demo
Super video. Tak 😃
Thanks
Very helpful. Thanks.
A nice demonstration :)
What you could also have shown is twisting the wire (as per the wires in cat cables). I use a hand drill to twist quite long lengths of sensor wire pairs together, also do the same on power wires, it helps a lot of emitted and picked up EMI.
I don't think this would have any effect on signal reflections
Good video!
What is the rise time of generated pulse?
The most fun you can have is a waveguide with a drop of water in it...
I tried the same with a potmeter -->
1. No reflection on the scope to begin with
2. Changingg potmeter simply changes amplitude
What could be wrong?
So if u connect the head and the tail before the voltage is out of the line.... :P
Fantastisk video, Takker mange gange :-)
Rigtigt lækker demonstration, jeg har altid haft svært ved at forstå det der med terminering af data ledere, nu tror jeg nok jeg har fattet det.
Hvis ikke du er flyttet langt væk fra hvor du boede før, så er der Hamday i Esbjerg, lørdag d. 4. maj 2019 kl 10:00, det er primært walkie talkie, men der er typisk også mulighed for at gøre nogle gode elektronik fund på loppemarkedet måleudstyr, komponenter og deslige.
www.hamday.dk/
What happened to your K40 laser?
Nothing happened ;)
It's in another room :)
Do you still use it after all of these years?
@@thebeststooge I didn't use it much lately, but I am sure I will use it again for some projects. :)
Excellent and I can't wait. I can't figure out what to use my laser for. :/
@@thebeststooge I made many things.
Christmas / birthday present tags, dog tags, led signs, jigs, keychains, mounting plates, decorations, gears, boxes, etc :)
Water, as we know it on Earth, is not really correct comparison.
It is rather air, gas or, if we want to be correct - ether.
🥸👍