Video

Thanks mate!! Did it in two secs!!

Great video. Do you even need to lift and take wheel off or could you do without it? Just wondering since I have no place to safely lift my truck and gonna start this today

I am changing the cylinder head on a Boncat 773. Although I ordered the cylinder head for the V2003T, it arrived different from the original. After checking carefully, this one is for the Kubota V2003-DI, direct injection. Would it be possible to put this cylinder head in place of the previous one?

Hello, thank you very much for sharing your knowledge, congratulations Sir, very well explained.

Are there products that would re-dye the cover?

Would be nice to know the torque specs

Thanks man, finally a video that shows how to do it, and nothing else.

How do you set the torque on adapter

Thanks for this video. It really helps me with decision is it worth to buy these quarter panels. I will probably try to fight with civic iv quarter panel.

Thanks from the crx community

Camera man didn't take full advantage of the opportunity to film the 'mog. Boo

Is too expensive

take my money

Awesome job 😊

what half shaft is this?

I got mine to turn back on, but now it won’t turn off.

If you use spring clips on the external edges you will get an even tighter joint

How many times have you found your architraves glued firmly to the floor?

Thanks for the information. My belt had been complaining severely and finally failed tonight. Made it to the parts store on the battery and then home and with your videos help. Done and done. Thanks again.

Till you find out how in accurate it is

Is there any problem for vechile

I am about to install the same panels in my basement. My house is from 1972 and I just removed the previous vinyl floor to find a damp concrete slab. Since there were vinyl planks on the concrete, after removing the vinyl floor it also started to smell of mold. I am now in the process to clean up the concrete but am wondering if I should put a rubber membrane. I found products like Blue Seal - The ultimate waterproof rubber membrane. Would you consider adding that under those panels?

Hello, Any update? Did they fixed those quarter panels?

Hello, I know that this video is old but I have few questions about these quarter panels. Have you got any photos or video how does these quarter panels looks like on a car? Did they look like the original ones (I mean shape of wheel arch)? It is hard to evaluate from this video and also pictures from the wolf steel store. I know that many people use quarter panels from civic IV gen to crx but they quite different. Those for crx have different shape from those from civic? Quarter panels from civic are cheap compare to those, but if these ones to crx have shape of arch as the original if think they are worth money. thanks

Must have removed center bump which consumes whole space of passenger seats.

Saw another channel where they then covered the soaked paper towel with a plastic bag to prevent drying out. They said Evaporust encourages this for large projects and even then placing magnets on the plastic to ensure close contact to prevent drying out.

I couldn't find a name for this product. A little help please?

Lord...the voice was hard to listen to

Thank you for getting to the point fast!! There is nothing worse than a long intro full of useless info

Exactly what I was looking for. Thank you so much.

You can also loosen the front diff bracket bolts that bolt above to the frame just loosen them aluttle then you can push up on the bracket to get more clearance to remove housing.

I wish you lived in Alaska, your work is amazing!

Monstrosities 😅

I was able to wire my basement timer direct to my HRV and it works perfect. Easier than trying to tie into the upstairs timers.

How much area does the 22 liters cover?

If it clicked instead of beeped and allowed you to go past the settings, I'd like it more.

Se puede poner en espñol?

How do you add access for the basement floor drain? Thanks.

Mine broke on my way to work. It was dangerous, but I was able to pull it over and walk the rest of the way. Picking up the belt after work,thanks for the quick tutorial.

The part is listed as a surge suppressor.

Tool Tested Channel actually did a thorough review of this model, turns out it's overpriced junk, completely out-of spec and inacurrate out of the box. The Harbor Freight worth $20 is way better than this.

A video about how to install lights where the guy doesn't install the lights. It should be called how to install a junction box

Let's just admit your after crxseth. He has 10 X what the people are asking for organically he has exactly what oem spec asking for.

Free Milton

Bro in your first comment, and if your Free matket

Music is too loud, I would rather hear you!

Super helpful , Thanks!!!!!

This was just what I needed! I watched the video, picked up the part, and had it replaced within an hour. Thanks!

Hi great video... where did you order your parts lf you dont mind me asking? Kms, bussybee, lee valley?. I'm about to do to the same conversion. I'm still hesitant about getting the 5hp or 3hp motor though... you have any comments on that? Cheers.

Hey thank you for the video very informative I have a 01 Chevy Tahoe and the front differential is similar to my mines my Right side is leaking, my question is should I replace both sides since I’m doing right side? , oh and btw I drop whole differential I guess I didn’t need to do that but hey you learn