The broken front axle of the truck, I did a joint for the first time that no one dares to do

Sdílet
Vložit
  • čas přidán 3. 05. 2024
  • Correct repair procedure in case of broken front axle of truck due to overload which not every mechanic can do
    #repair #correct #broken #front #axle #truck #overload #mechanic
  • Auta a dopravní prostředky

Komentáře • 22

  • @dadbehrouhbakhsh626
    @dadbehrouhbakhsh626 Před 22 dny +2

    The axle broke due to a combination of overloading and bad roads..I'm not sure how long this new welded axle will hold to the same treatments..

  • @zecasiqueira9262
    @zecasiqueira9262 Před 16 dny

    Esse rapaz de óculos e bom de torno e proficional

  • @chickenlife6317
    @chickenlife6317 Před 27 dny +3

    RIP truck driver.

    • @mutterschied
      @mutterschied Před 22 dny

      Why? The welded surfaces 'r' stronger than when processed, you engineer...

  • @j.conxcara381
    @j.conxcara381 Před 6 dny

    ya que han hecho una reparación tan chapucera, podrían haberlo compensado poniéndole un refuerzo.

  • @user-dj5gf9jp8g
    @user-dj5gf9jp8g Před 27 dny

    Cool work thanks 👍

  • @holycrapski
    @holycrapski Před 12 dny

    A little knowledge is a dangerous thing (For others in this Case).

  • @thomasbor
    @thomasbor Před 25 dny +1

    say good bye to castor and camber angles....

  • @PeterChapman-rg6gr
    @PeterChapman-rg6gr Před 27 dny +1

    Some poor truck driver is going to regret that this bodge was ever fitted to his lorry.

  • @user-si5qz7rp7b
    @user-si5qz7rp7b Před 27 dny +2

    СТО раздолбай моторс придумало новую технологию восстановления передней балки всем перекупам нужно срочно брать с них пример.

    • @Bosjak63
      @Bosjak63 Před 24 dny +1

      Посмотрел твои видео
      Раздолбай моторс как раз у тебя, у них хотя бы в цеху чисто
      Да и технология реставрации балки несмотря на кажущуюся примитивность вполне рабочая, это видно по тому как они её исполнили. Сразу заметно что не в первый раз !

    • @user-si5qz7rp7b
      @user-si5qz7rp7b Před 22 dny

      @@Bosjak63 у меня хоть верстак и тиски есть.

    • @user-si5qz7rp7b
      @user-si5qz7rp7b Před 21 dnem

      @@Bosjak63 чтобы кого ни будь критиковать за бардак и грязь в цеху нужно иметь хотя бы гараж а не арендованное парковочное место.

    • @Bosjak63
      @Bosjak63 Před 21 dnem

      @@user-si5qz7rp7b Тут проблем нет..
      Был гараж - был порядок
      Сейчас арендованое парковочное место, ничего не изменилось - так же в чистоте и порядке!

  • @TheUltimate65
    @TheUltimate65 Před 27 dny

    Did the have Full controll over the camber angle then...🤔

  • @mrphotomanseattle
    @mrphotomanseattle Před 28 dny +1

    Please explain why they drilled and drove in the pin. Is it for stress relief?

    • @bills6093
      @bills6093 Před 27 dny +3

      The pin makes the joint stronger since they were only able to weld around the outside. So the pieces are both pinned and welded together. Probably should have used a shorter pin that set below the surface a bit, and then welded the pin in place at both ends. Such a repair in the West would get you arrested, though.

    • @AlirezA_TEX
      @AlirezA_TEX Před 26 dny

      Maybe for more strength than the central part

    • @AlirezA_TEX
      @AlirezA_TEX Před 26 dny

      ​@@bills6093exactly

    • @AlirezA_TEX
      @AlirezA_TEX Před 26 dny

      ​@@bills6093exactly

  • @freshhealthy8118
    @freshhealthy8118 Před 28 dny

    ❤❤❤❤