Video

Using a thin grinding wheel, he could have ground a deeper keying slot in the dead tooth ! & when welded in, it would be even far stronger, and that the force that broke the tooth in the first case, would encounter a much tougher tooth and be far less unlikely to break in that spot on a second time.

We fix for you! See you in a week when it breaks again! Happy day to you! lol

Excepcional

Мало того что обломало ось еще и повело искры не равномерно пошли а станок хотя и новый передачи ремнем перебрасываются значит на панели их нет бедные людишки 😊

THIS IS NOT, NOT, C.N.C. MACHINING !!! C.N.C. IS COMPUTERISED COMMAND AND CONTROLLED MACHINING BY COMPUTER PROGRAMMING! THESE MACHINING TECHNIQUES ARE TRADITIONAL OLD SCHOOL( MANUAL) MACHINING PROTOCOLS! WHICH ARE EXCELLENT !!! BUT WAY SLOWER! AND THE SPPED FACTOR? SAY IN NORTH AMERICA IS IMPORTANT TO REDUCE LABOR COSTS! OUR SITUATION IN NORTH AMERICA IS NOT, NOT TO BE ENVIED! IT IS HUGELY COSTLY AND EXPENSIVE TO MACHINE ANYTHING IN NORTH AMERICA! THINGS ARE PRODUCED AT LOW PRICES HERE? AT LOW PRICES? ONY WHEN IT IS DONE AUTOMATICALLY? AND IN LARGE MASS PRODUCTION QUATITIES! EVERYTHING IN LIFE? IS A TRADE OFF! ??? BUT ALSO? IN PAKISTANY TERMS OF COST? IT IS STILL ONLY THE PERSONS MAKING GOOD MONEY WITH THEIR MACHINES? WHO WILL HAVE THEM REPAIRED OR REBUILT!!! BUT IT IS STLL IMPRESSIVE WATCHING THE CREATIVENESS OF PAKISTANI TECHNICIANS, MECHANICS? AND MACHINISTS!!! kennethzakaib607@gmail.com Montreal Canada May 2024

Estos trabajadores son fantásticos, tienen soluciones para todo, mis respetos 👍👍👍👍

если смотреть на излом оригинальной оси, то видно что деталь с поверхностной закалкой. середина вязкая, поверхность твердая. Сплав соотвествующий. После ремонта ни о качестве материала ни о термообработке речи нет. Такой колхоз до первой серьезной нагрузки

햐 파이프는 통으로 갈줄 알았는데 땜방을 하네...

O colega e bom de torno kkkkkkkkkk

Esse rapaz de óculos e bom de torno e proficional

We start off with a broken CAST IRON housing. It is then threaded and a very loose fitting steel insert is screwed in. This is then welded with 1 run of "Pac Bridge" 6013 welding rod. Note no pre heating, post weld controlled cooling or even the correct welding rods for cast Iron to Steel welding. This weld would have cracked at the casting when it had cooled down. The exact same applies to the steel plate that was very loosely screwed into the other part of the Cast Iron casting. Again welded with 1 run of the ubiquitous "Pack Bridge" 6013 welding rod. This is yet another in a very long line of pure "Click Bait" videos with a bodged "Repair" that will never be fitted to any vehicle

Nice

How much does turning work cost?😊

Very good repair, but you should have welded the big ring on the inside as well as the outside.

Me gustan sus videos pero lo que no me gusta es que inician casi con un minuto del vídeo y luego se regresan y vuelven a empezar 🤔🤔 háganlo bien desde el empiezo y no así ok? Saludos de México 😊

پیراؤ

You are very able,good.From Italy.

❤❤❤❤

CNC Master 1 CZcams channel the best from Pakistan and the world ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

CNC Masters 1 channel the best CZcams channel from Pakistan and the world ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

Hand cut gear tooth? I also believe this was for entratainment only.

Admiro o trabalho de vcs parabéns 👏👏🇧🇷

As pointed out, the old repair failed, redoing it will have the same result.

Chromed rod hmm. Check out cutting edge engineering they are the best for this sort of thing. They always send the rod to be rechromed. Interesting comments below. Maybe they did replace it anyway. Cheers from Australia. First time I have commented about your work practices.

Excellent job keep it up 👍

Repairing this axel in the same method as before is obviously a patch more than a repair as the break occurred at the same point as the previous repair.

Ну понятно, если дурень платит деньги, мы сделаем... Это не будет ходить))

In India, axles were over-designed, due to pressure from the truck lobby.

Damage to the roads and risk of lives.

A flourishing repair industry, flourishing due to overloading. A similar situation was prevalent in India,but due to crackdown, by the authorities, less prevalent now.

Here is a lot of money to be made in overloading, as repairing is cheap.

Quá giỏi

EXCELENTE VIDEO¡¡... Y MUY FACIL DE ENTENDER¡¡...SALUDOS DESDE MEXICO¡¡

*Hello, exceptional as usual*

❤

*مرحبًا، استثنائي كالعادة.*

Está carcaça é de aço ou ferro fundido ? Que eletrodos você usou para fazer este cordão de solda ? Ótimo vídeo e parabéns pelo trabalho ! 👍🔨🔧

Mr sneakers must be the bossman..

عظيم، مذهل، ماهر في التصليح.

Really look forward to your videos.😎

Cool work thanks 👍

Им просто до ехать до места а там опять варить

Порнография какая-то. Работать - нагрузка будет только "трубка-рубашка" а диаметр вала не зря такой величины..... поэтому надо весь диаметр вала проваривать.

11:44 some of the gears look deformed like it was only engaging on the side that broke. Might be a shadow.

I think it is absolutely horrible to do this :] What is cool though is that this guy could make the whole gearbox using just an angle grinder:]

Какой марки электроды?

The axle broke due to a combination of overloading and bad roads..I'm not sure how long this new welded axle will hold to the same treatments..

Basura de camiones don pura soldadura no remplazan nada

Top 🇧🇷

Top 🇧🇷