It is not difficult for me to assemble a broken axle housing like a pen
Vložit
- čas přidán 25. 12. 2023
- It is not difficult for me to assemble a broken axle housing like a pen
#difficult #assemble #broken #axle #housing #like #pen - Auta a dopravní prostředky
It's strange that the break is so square, it had probably already broken there before.
Otro gra trabajo,que por cierto,un trabajo imposible de hacer en España,salud y buena suerte...🐧
Mashallah Good work amazing zabardast
That differential been "repaired" many many times before
No way they're getting %100 penetration without beveling the edges before welding.
I want some of that Pakistani welding rod- gets penetration through mud, oil, grease, dirt and you never have to bevel your parts.
Not even 25%!
And not cleaning the weld surface? All that grease and dirt in the weld?? SMH
🙌🙌🙌🙌🤣🤣🤣🤣
Yes. They had the root clearance but what happened to the 60 degree V? Also how do you weld into iron oxide from the flame cut - plus no V? As others have mentioned maybe 25% penetration. Wonder how long the always overloaded truck lasted afterwards?
They have to overload the trucks to get the job, then drive a dangerous vehicle to make money.
After that they have to spend the money they made for repairs.
Not an ideal system.
I'm impressed with how much they get done with basic tools if they didn't overload the trucks wouldn't have catastrophic failures
Only one man wear shoes, others sandals, no gloves, no safety glass sorry for those people, they don’t have any protection at all
No prep before welding shocking work
Strange regular failure, scam?
It must be a very common factory problem, due to the type of cut and they even have a lathe designed for that type of axle.
Что за диск на болгарка не убиваемый индусы молодцы , Вася Я ишим
Молодцы ребята , у вас золотые руки и наплюйте на все санкции --вы все равно правы.
No good welding because they did not make edge preparation at all.
therefore cannot get good strength.
Wonder how they check the axle is aligned with the diff centre
Ten most już kiedyś pękł i pęknie ponownie.
Przy takim przeładowaniu pęknie...
Dziwię się, że nie fazują krawędzi przed spawaniem.
It's amazing what you guys do with what you have. No big shop with all fancy tools. Use the basics to get the job done. Good stuff. 👍👍🇨🇦🙂
Meets or exceeds all 3rd world country safety and repair standards.
Bagus,Paman 👍👍👍👍
Install a rubber mat in back of vehicle to protect the bed.
Những người thợ khá tốt nếu vào hảng sẻ thay một cái mới rất tốn tiền
This kind of work never succeed. Not advisable. Foolish work.
Cool work thanks 👍
No groove for welding root run penetration
so that's a broken axle no that looks like its been cut up to look like a broken axle and the back end of the axle been fix up be for , can see the cuts in the axle . on the bearing shaft where the bearing sits had it , there been no oil or Greece on or in axle for some time where the axle shaft gos in got lot of rust in the ends
didn't clean the part where you groove for welding
Yeah safety first I always say
I wonder how much stuff they get in there eyes
New pickup hauler…
4:39. 🤦🏻♂️🤦🏻♂️🤦🏻♂️
LMAO
Just another show and tell made for CZcams.
도로가 무법천지네 신호등도 없고
Great job done.Good welding strong as new.
Cowboys
No they are indians
BY g
Fake failure and stupid repair !
Well if it broke underneath!!!!!!maybe this is the problem and a modification is need it!!!!! 21:02 🔴🫢🤫
Love it !!!!!!very smart move !!!!!!,🔴🫢🤫 16:45