2004-2013 MAZDA 3 PROGRAM REMOTE & KEY (ON-BOARD/AUTOPROPAD)
Vložit
- čas přidán 6. 03. 2020
- This remote program procedure works for models 2004-2013 ... mazda 3 ... in order to program the chip you need a programmer!! Please hit like and subscribe to my channel thank you!!
CASH APP: $PAYMEMONEYMIKE
Paypal:
paypal.me/mike90f?locale.x=en_US
Use these instructions to program the remote portion of your flip key.
1. Remove key from ignition
2. Close all doors.
3. Open drivers door.
4. Perform following steps within 24 seconds.
A. Turn ignition switch ON and back to LOCK position three times
B. Close and open drivers door three times
C. Door locks should lock and unlock automatically, if they do not wait 40 seconds and repeat procedure starting at step 1.
5. Press UNLOCK button of each keyless remote to be programmed twice, door locks should lock and unlock after each remote is programmed. If door locks do not lock and unlock proceed as follows.
A. Close and open drivers door once, door should lock and unlock twice. If door locks do not lock and unlock, start procedure over with step 3.
6. Exit vehicle and test remote(s)
Step by Step How to Program chip Instructions: must have two already programmed keys to program a third key!
Use these instructions to program the key portion of the flip key.
Key blade must by cut to operate ignition
The timing is critical to this procedure, please read through the entire procedure before attempting.
1. Insert one of the programmed transponder keys and turn the ignition to ON, leave on for at least one second (Wait until the red key symbol in the instrument cluster goes out), remove the key from the ignition.
2. Within 5 seconds insert the second programmed key and turn the ignition to ON for a least one second but no more than 5 seconds, then remove the second key.
3. Within 10 seconds insert the new key in the ignition and turn the ignition to ON, if you are successful the red key symbol will illuminate then go out in about 1 second.
If you are not successful the red key symbol will flash repeatedly to indicate that you have inserted an invalid key. Remove the key, wait one minute and try again.
For the first time in 15 years I have found a CZcams video that gets to the point and actually works. I appreciate you cutting to the chase cutting out the fluff and telling us how to do it. You did not tell us the weather forecast the traffic conditions what your grandmother had for lunch your kids report card grades or anything like that you just told us how to program the remote. Hallelujah
Hahaha thank you brother I appreciate your sincerity!! Dont forget to hit like and subscribe
Brilliant! Worked first time. The battery had got so low that one day we opened the car but could not lock it again. Changed the battery but still did not work. Your re-programming advice worked perfectly. Thank You!
Glad it helped
Thank God you made this video! I took my Amazon bought keys to a locksmith and they couldn't program my remotes. Came home, went on CZcams, found your video and boom! Programmed in 2 minutes.
Thanks
Right on great job!!🙏🏼🙏🏼
Did you use xtool to programm the transponder chip?
It worked PERFECTLY! Thank you so much for a quick, easy and accurate video!
Thank you Erica im glad it worked out for you!
Thank you so much for this video, straight to the point and it worked first try for me!
Thank you im very happy you liked it!
finally somebody who really show the rigth way!!! fallow for ever
Thank you!! 🙏🏻 God bless you !
Thank you so much for your help and I agree with the comments. Thanks for getting straight to the point.
Thank you for watching glad you liked it
Thanks you're a life saver! Worked like a charm on my 2012 Mazda cx9. Hope this helps!
Great to hear!
Thank you!!!!!!! 👍 best video. This worked for my 2012 mazdaspeed 3 NON smart key 👍👍👍👍👍👍👍👍👍👍👍
Excellent instructions. It worked perfectly
Im glad it worked out for you! God bless!
You saved my life bro, very very pleasant tip
Bro just wanted to say thank you
This helped a lot 💯💯💯
No problem 👍
If you have only 1 key......take the key blade off as if you were replacing the battery. You will have 2 parts now. Insert the key blade part in the ignition. Follow the steps as outlined. Use the key fob part to press unlock twice at final stage. Turn key blade part to on once more to deactivate programming mode.
Your instructions worked. Thanks!!!
Can you clarify more your instructions?
Worked great thank you! 2007 mazda 3!
You're welcome!
What if there is only one key? Can a second key be programmed with the key tool max?
00:35 I feel like I am in GTA San Andreas and using cheat codes!! 😭😂😂
thank you for watching im gld you liked it!!
Thank you bro I appreciate the tutorial
Thank you Marcos
Thank you very helpful
Thank you for watching!! Hope your having a great weekend!!!!
Great video!! was able to get both my fobs programmed!!!
Thank you for watching
But did the car start ?
@rrios283s73 yes it did!!
You the man! Crazy easy, thank you.
Thank you brother!
What obd scanner you use?
You can use a flipkey key fob with a 2005-2009 mazda3? I would like to use one of those with that kind of car if I get one.
I lost my only key for.my mazda3 hatchback 2011 will this work with just the cut key I'm getting from mazda dealership ??
That worked thx
Thank you!
Saludos desde Mississippi colega
I really appreciate your help
Thank you, Thank you, Thank you very much
I got my key fob programed man,
You're so awesome, Thank you 😊
Glad I could help you! Thank you
Para llaves perdidas se nesesita programar dos llaves o solo con una basta ?
Thank you 👍👍
Thank you!🙏🏼❤️
Would this style key work on an 08 speed3 5 door hatch? Just picked it up today and thought it was odd there wasn't a fob. If I can buy one of these switch keys that would be great
Hi after I open and close the door three times, my locks aren’t cycling. Any idea why? Mazda 3 2010
Is there any way to look up which cars require onboard programming?
Like a manual such as auto smart books
behind the ilco autotruck key reference book there is a guide that tells you wich key you can do on board programming
Hi
I did all the processes exactly like in the video but still not working :( any suggestion will be verry appreciated. I have the 2008 model 1.6 Diesel
Is it the mazda 3??
2010 Mazda 3 remplace la pcm usado y ahora no prende,que tengo que hacer para programar la llave gracias
Thanks
Thank you for watching glad you liked it!
Can anyone tell me how to do it on a mazda 2 from 2008? I have one key FOB and one regular key. The fob buttons doesnt work, even though i changed battery.
I’ve got the same key as yours minus the panic button and the boot release. I want to buy a key with the panic button to replace mine which doesn’t have it. Do you think that it will work?
What year and model is your vehicle????
MY KEYS AUTOMOTIVE it’s a 2010 Mazda 3 hatchback. Not keyless entry or push button start.
Yes !! Key will work just make sure you match the fcc id and part number!!
MY KEYS AUTOMOTIVE yeah about that I can’t find any FFC ID on it. It’s it located under the the flip key? Mine just says Mitsubishi Electric under there which I thought was odd.
I have the fcc id on my video in the beginning and part number!!
I have a Mazda 3 (2004) and the remote just stopped working (no flashing lights eigther). I changed the battery, resolded the contacts but still nothing. The remote is working, I know cuz it's been tested, and it has signal. What can be wrong with the car? It can be a fuse problem? Lock - unlock it's working only if I turn the key, and it's very annoying. I don't know what to do! Can you help out? Thanks!
Probably bad fuse or something electrical
@@MYKEYSAUTOMOTIVE I can't find that fuse
when i do the 3 key turns and open and close door 3 times, my locks cycle twice and then the rest of the steps dont work. help please
Hello greetings! 👋🏽👋🏽For priority commenting please join our members club! Next the subscribe button from a laptop or desktop you will see the join button!! Thank you!🙏🏼🙏🏼❤️❤️❤️
Found this video on a random page. I have 2 Mazda keys that have nearly stopped working. Mazda Scotland want $1000 for 2 keys. I'm away to change the batteries and do the 3 times thing hahaha. Hope it works.
Somehow my key that I useally use is not working (just the remote)
Can I use this steps to reprogram it? And why could this be the issue? The battery is fairly new and the light flashes so I guess its not the battery.
Yes but i would try replacing the battery either way !
I have a 2011 Mazda 6 that shut down whike driving.
There is no power to the coil pack not fuel injection.
We change three crank sensor as we thought that was the issue, but problem never solved.
Currently the car is parked as no one seem to be able to figure out the problem. It was scanned but nothing came up.
I was told the computer needs reprogramming as the lock symbol flashes and it should be ok. I did all that but nothing changed.
Could the key lost the programming and this caused the issue?
Hmm could be a faulty key.. or bad ecm..
Where did u get the car from??? How long has it been doing this for?? How did the issue start??
@@MYKEYSAUTOMOTIVE I got it from Japan. The issue just first started about 3 months ago while driving, the car just shut down and I restarted the car. About a month afterit happened again and I restarted the car. Now I am not so fortunate to have it restarted after saturday 19.12.2020
@@MYKEYSAUTOMOTIVE never knew there could be a faulty key. I will check it out.
@@MYKEYSAUTOMOTIVE does my car have a key Icon to indicate that the imobilizer is activated or not?
I do see a flashing red lock and car symbol.
Please guide me - Good afternoon. Thank you for the great video. I have a 2010 Mazda3 (not a hatchback), Unfortunately, it not working for me. I tried all the steps. the only thing that started happening, now I have a red blinking light on the dash, that is an anti-theft light I believe. My car never did the locking and unlocking cycle. Please help me, What should I do next?
I only reply to members sorry
I have a friend with a 2010 Mazda 3 I removed his cluster to check it , because it was gittering ,put a used one in and the car won't start ,put the old one ,car still won't start , security light flashing,try to program key with autel 908 pro , security access denied????
Must synce cluster to vehicle
I just bought a 2011 Mazda 3 hatchback 2.5, but the key that came with it is a standard key with Mazda logo. Would this have immobilized chip in it? I’m looking to get a key fob for it. Would the one you used in the video be the right one? Any help would be great.
Yes it has a chip.. yes
2008 Mazda 3 2.3 I want to switch to a flip key but I don’t know what chip and fcc I’d I need
Mz34 transponder key
@@MYKEYSAUTOMOTIVE fashion
hey I just lost my key to my 2010 mazda hatchback can i do this without the propad?
I’m afraid not
I have a 2011 Mazda 3 and I only have one key fob. The key works but the buttons do not. New battery and won’t work. I get the red light in the center of the fob when I try to lock and unlock but won’t work
Hello greetings please join our members club for priority commenting!! Thank you! ❤️🙏🏼
Same thing! How do I fix it??
I was working on 2012 Mazda 3, I followed everything but keep saying “failed” using APP. Do you think it’s the transponder chip mismatched? Th FoB works smoothly
I bought the key from Amazon.
BTW, thanks for answering for all my questions lately. You’ve been a big help on my small journey
Hello Ap video and thank you for the support!! From my experience yes it could be an incorrect transpondedor..what programmer are you using?
@@MYKEYSAUTOMOTIVE AutoProPad basic
So it says it needs a 4d63-80bit same like ford.. you might want to double check chip
My car is 2011 mazda 3 hatchback. I did exactly as your procedure but locks would not cycle as step 4c . Tried multiple times, still not working. Can't figure out why. Any idea? Thanks,
Check your fuses
Nice video 😊,I have a 2010 Mazda I try switching the dash and the car wouldn't start so I put back the original dash still won't start security light flashes ,I try to reprogram it with the key cycle and the door close n open ..I tried using autel 908spro it ask for code ..any ideas please
Hello greetings 👋🏽 Friend! for priority commenting please join our members club! once you join you will also be entered to win for our monthly giveaway! If you want to join ,you can join from a laptop or computer next to the subscribe button you will see the join button!! thank you!🙏🏼❤️
Boss how can you tell what type it is ( on this video you said it’s a type 1 ) how can I tell ?? Where c da n I find this type of info ?
Hello Melvin usually you will find the information on Autopropad.com under vehicle list search year and model .
I have 2011 mazda 3 my original key works fine. But when trying to program 2nd key the first cycle never starts, why?
Its not going into program mode
I'm trying to program a Mazda 5 2008 and I'm not getting the all keys lost option on my pro pad
its not compatible
try updating it
Is there a way to do this with just one key?
Hello. I lost my original key on my Mazda 3(2008). Can I program the key(I will buy it online) without the original key. Thank you.
No sorry you need to call a locksmith
Thank you...
how do you do this with copied keys with out the buttons my 2006 mazda 3 anti theft mode is on and i cant disarm it got car from auction please help
Do you have the key programmer?
Does not work. My original key somehow stoped working..I started the program and I get to the point of pressing 2 times the unlock, after that, nothing. Any tip?
Replace battery
So where do i get the app/tablet plug in to program this?
Uhs hardware!!
@@MYKEYSAUTOMOTIVE I have a fob key i bought on Amazon, can i just have it cut, and program it my self?
Miguel Vasquez the fob yes .. the chip no!! You need a programmer.. i know the ford system you can program a third key if you have too but i dont know if mazda would work the same way.. i kno the use same chip thats why i say that.. but i highly doubt it!
@@MYKEYSAUTOMOTIVE I took apart my old fob and put all the parts in a new fob case. I couldn't figure out for the life of me why it wouldn't start. I went through the old pieces and found the chip. I put it in the new fob case and bam, started right up. I thought it was a piece of broken plastic. I would have never figured that out.
Was driven crazy trying to get new key to work on mazda 3 2005 model BK
Easily reprogrammed two keys I bought on Amazon.
🔥🔥🔥👍👍👍
We're u able to start the car ?
What is the name of the unit you used for immobilizer?
Autopropad
Can we program the immobilizer without your machine ?
No im sorry 😢😢
Where did you buy your pro pad from ?
I bought it used, try ebay or internationalkeysupply.com
@@MYKEYSAUTOMOTIVE thanks for answering. It's cause I'm having trouble with 06 Pontiac Grand Prix can't program key with an autel. Does the pad pro work with that vehicle thanks again
Juan Rodriguez yes the autopropad can program the pontaic grandprix 2004-2008 ,doesnt support earlier models like 2000-2003
Nice video, thanks for all this good info 🙂
Aura Infantas thank you for watching!! I appreciate you!!
On a 2013, would this work to program a 3rd fob for the Smart Key system (push start)?
Nooo😭😭😭
Are you able to rent that device anywhere or you have to buy it?
Must buy no renting
anyone knows why trunk button doesn't work? everything else works😢
Is thier a fuse for the immobilizer
No
You know what I'm going to buy a Mazda remote key
Awesome!
How come my door won't do the lock/unlock cycle?
The program is probably not compatible with your vehicle..
@@MYKEYSAUTOMOTIVE I have a 2011 mazda 3 sport hatchback
@@garrettkogelschatz9705 did you ever figure it out man ?!
@@ihopeurokay5120 no I unfortunately did not. I’m back here trying to figure it out so I can quit using the dummy key to unlock my car with the door key hole
What industry are you in? I’m desperately trying to find someone in my area who has this so I can pay them to come program mine.
Tuve un carro con el mismo año y modelo pero nunca lo pude hacer que entrara en modo de programación para la sección del control te a pasado halgo similar?
Muchas gracias
Todavia no me a pasado, aveces los fusibles no estan bien se acupan chequear .. o es un problema electrico ⚡️!!
I did that, it just lock and unlock but remote still not working
Wrong frequency or bad battery
@@MYKEYSAUTOMOTIVE I have a new battery, when I jump the starter, it starts, I just don't get no connection in the main relay
Are you able to do this without the software?
Hello greetings 👋🏽 Friend! for priority commenting please join our members club! once you join you will also be entered to win for our monthly giveaway! If you want to join ,you can join from a laptop or computer next to the subscribe button you will see the join button!! thank you!🙏🏼❤️
Does it work to programm new key?
Remote part only
Hi where to buy this key?
Uhs
UPDATE I got the lock and unlock to work. However the trunk and panic buttons do not work.
Hmmm could be a bad key.. wouldn't know what to tell you unless you check the frequency at autozone.. see if they can check the frequency on the panic and trunk button
No computer…guess I gotta pay the $180
is this the same for mazda 6?
\
What year?
@@MYKEYSAUTOMOTIVE 2010...iwent out side and tried it. it DOES work. the car responded as in the video. so i ordered new fobs. still need to see if it work completely.
What happens when you have only one key and no spare?
Hello friend! 👋🏽Please join our members club for priority commenting and a chance to win in our monthly giveaway!
You can only join From a desktop or a laptop next to the subscribe button.
Thanks!🙏🏼❤️
I did this and nothing happened the only thing that happened was my car had trouble starting after … I had to give it gas to get it going
Where i can find mazda keycode ?
If you get lucky you might find it on driver door lock if not you will have to lishi or order from magickeycode.com
So what’s the purpose of the chip? If I buy a new fob, get it cut, and program the remote, it would be able to unlock, lock, and start the car. What does the chip do and why is this step necessary?
no the car wont start without programming the transponder! its for the anti theft system.
Mazda cheat codes
😅😅
Well it seem to work for everyone one except me 🤦🏽♂️ 🙄
THIS COMMENT IS ABOUT ADDING A KEYLESS ENTRY REMOTE (EITHER A KEY FOB OR THE BUTTONS ON THE KEY), NOT ABOUT ADDING A KEY TO START THE CAR.
o-o-o-o
If you are having trouble programming the car for a keyless remote because the door locks will not cycle after you close and open the driver’s door 3 times:
m.czcams.com/video/twvXTyqLvF4/video.html
it is probably because this car never had the Keyless Entry System option. This means that you cannot add a keyless remote to this car.
The Keyless Entry System is an optional feature. Look in the owner’s manual and note the asterisk “*” at the bottom of the page for Keyless Entry System. It says “Some models”. Not all cars have the Keyless Entry feature.
why you dont just clone the chip
I try not work i do all steps i here lock and unlock then try the remote not working
Year and model??
@@MYKEYSAUTOMOTIVE 3 2008
Does the vehicle go into programming mode??
@@MYKEYSAUTOMOTIVE yes i hear lock & unlock but my rear door the lock switch is broken