Domino Connect or Lamello Clamex? [video
Vložit
- čas přidán 27. 06. 2019
- In this slightly longer video I take a closer look at the different #knockdown connectors from #Lamello and #Festool. Enjoy
Please use the ‘Like’ button if you liked this video.
Please subscribe if you think you’d like to see more.
My ‘social’ links in one place - bit.ly/10minute-links
Support me directly - bit.ly/donate_to_10minuteworkshop
Support me on Patreon - / 10minuteworkshop
Full list of ‘Stuff I use’ at
Connect with me on twitter @10minuteshop
Connect with me on Instagram - @10minuteworkshop
+++++++
As an Amazon Associate, I earn from qualifying purchases made through these links.
Wherever possible links are to actual products used, but this is not always possible e.g. some products are not available in the US, so something similar has been linked to instead.
Amazon UK - www.amazon.co.uk/shop/petermi...
++++++++
Used/featured in this video:-
Lamello Zeta P2 - amzn.to/2Xpu5vB (US: amzn.to/2Kufuv1)
Lamello Tenso P-14 - amzn.to/2Z5i4eX (US: woah - are these not available in the US??)
Lamello Clamex P-14 amzn.to/2Wkm922 (US: woah, again??)
Festool Domino - amzn.to/2pVSnMk (US: amzn.to/2o7E22Q)
Festool Domino assortment - amzn.to/2piZjHa (US: amzn.to/2pGv1Lx)
Festool Domino 5 x 30mm - amzn.to/2oTq5CZ (US: amzn.to/2oOqyrL)
Festool Domino connectors - amzn.to/2mV8OJu (US:amzn.to/2LKRDZ1)
I bought mine from the nice people at ProTrade - bit.ly/ProTrade_Zeta
++++++++
Other useful bits & Pieces
Bahco 6” combi square - amzn.to/2oumhX4 (US: amzn.to/2ouSg9k)
Bradawl - amzn.to/2qWTbln (US: amzn.to/2pZqVRm)
Mirock square - etsy.me/2MC0RTZ
Plastic packers - amzn.to/2vCDN27 (US:amzn.to/2vHk4fZ)
Moldex 6810 in-ear defenders - amzn.to/2sTwQJE (US:amzn.to/2sThGo1)
Hultafors Talmeter tape measure - amzn.to/2pHwnbH (US: amzn.to/2oqLQc9)
Festool lever clamp - amzn.to/2pOohLD (US: amzn.to/2pnFZIM)
Bessey Duo Klamp - amzn.to/2tsSWQs (US:amzn.to/2sVaRBH)
Braided hose sleeve - amzn.to/2puFkWd (US:amzn.to/2oqbQsi)
Polyvine PolyTen PVA - amzn.to/2HBxK66 (US: amzn.to/2rmHYL3) - Jak na to + styl
![Peanut 2 Mini Jig[**Gifted/Ad] Video 439](http://i.ytimg.com/vi/DsvpAjGizKs/mqdefault.jpg)
![Peanut 2 Mini Jig[**Gifted/Ad] Video 439](/img/tr.png)
![My 5 Worst Buys! [video 484]](http://i.ytimg.com/vi/5uoQ78879Es/mqdefault.jpg)
Very interresting Peter. After seeing this video and the points you mentioned I will defenetly say Lamello. Thanks for demostrating the difference between these two systems, it was nice to see in close up how they work.
I don't have such fancy machines - heck, I don't even make cabinets most of the time! - and yet I keep watching your videos Peter, because I like your style and in-depth explanations and reasoning.
Thank you! 👍👍
Hi there!
I am a Clamex S fan. They can be used with a regular biscuit joiner. But you might want to check out Scheulenburg. They have connectors that only need a drill. Only drawback are the many pieces like in Festools system.
Regards,
Etna.
@@Etna.
I've got a lamello biscuits and gravy machine. Are you saying it can be used to install the lamello connectors?
We have both systems in our workshop and it comes down two things cost and different ways of working. If only had one budget one machine it be the festool it's just for one way of connection .not say these are cheap machines they are not .I could buy a decent morticer for the price of one machine .the zeta is brillant for carcase work and frame connection .as everything comes down speed over cost rule
Very good video Peter. Unbiased and honest. All your findings are spot on. 👍
Cheers Steve! Early days (for us all!) with the Lamello, but the Clamex are clearly a great general-purpose fitting especially for cabinetry, and the Domino Connect certainly has its place if you’re already a Domino user, and particularly for narrower-section stock. Good to have both at our disposal, eh Steve? 😆😂👍👍 👍
What a great resource you are Peter! I just started milling the lumber for a large wall-to-wall bookshelf installation at a customer's house. I was thinking of using the Festool connectors to assemble the pre-assembled "modules, as there is very little wiggle room side-to-side. Your note about the added width needed for the long peg just saved me a lot of headache from going down that rabbet-hole. Cheers!
Glad to hear it, thank you! If side-to-side wiggle room is an issue, then the Lamello Clamex is my fitting of choice as there’s just the little 5mm nubbin that protrudes - and you can actually trim that off and still get a very strong hold. 👍 The Clamex S connectors are due out next month - they work with a standard biscuit jointer blade - but if you need something sooner then the Peanut 2 connector can be used like a Lamello Divario (?) so it slides into the slot from the front. HTH P
Great comparison & information. Thank you!
Pleasure, thanks! 👍
Others have mentioned that they have no intention of buying either tool and i fall in that category, and yet i could not stop watching. If i was making cabinets all day as you are i would seriously consider one or other of these. They are awesome bits of kit and I could see how they would pay for themselves in no time. fascinating insight into a range of tools i would love but could never justify/afford. Thanks Peter.
Thanks Andrew! Good to hear you found it interesting, and I completely understand what you say about both tools being out of reach. I’m constantly surprised though, by how many people tell me that they have a Domino for non-professional use! The usual justification seems to be limited workshop-time available, and anything that can speed things up or help with efficiency is a good things. 👍👍
@@10MinuteWorkshop I agree I think if I was going to make a load of kitchen cabinets or a similar big job I would be all over justifying having one. I just rarely make things like that. It is amazing how tools come more affordable though. When I started wood working there would be no way I could have afforded a table saw. Now I have the DeWalt one like Andy Mac.
I found this video quite helpful, thank you!
I have the Domino 500 and 700 .. I like the 700 connectors but, like you, grabbed a Lamello for the smaller stuff. You'd happily put a bed together with the 700 connectors but I think they're clumsy compared to Lamellos system for things like shelves, etc.
Thank you sir very helpful.I HAVE both dominos 500 and 700 but clearly i am going for lamelo zeta no doubt about it.
Thanks! 👍
I'd never used the Clamex before until yesterday where I've used it extensively for a birch plywood shelving unit I've been making freelance for a company.
I have to say I'm very impressed at the simplicity, accuracy and ease with which the system works. Thing is though, it's eye wateringly expensive so for now, I'll not be getting one of my own. Great though.
Yes, Lamello starts to make Festool look cheap, lol! Great system though, big fan of the clamex in particular. 👍👍
I’ve been pondering which I should get, but after this video I’m surely leaning more towards the Lamello. Thanks!😊👍🏾
Thanks! Lamello’s a fine machine, but it’s more of a niche product than the Domino. Domino’s more versatile in eg narrow stock, but for carcass & cabinet construction the Lamello ticks the boxes. 👍👍
@Peter Millard - Thank you Sir. 😊
I have the Festool system and used it for the first time this week. It made sense for me since I already had a Domino machine. My only comment, other than this was a great video, is no doubt Festool designed this system for the posts to be removed for shipping. Otherwise, why bother with their system? I removed the posts and re-inserted them and they presented no issue with re-tightening. I wouldn't be concerned about that aspect. If I used these types of connectors as a business, I would definitely go with the Lamelo for all the reasons you said. BTW, so sorry for your loss on the passing of the Queen.
another great video peter, love your style of conversation
Thanks Andrew! 👍
+andrew roberts
It is an amazing system and you can build many things with it. There is a cheaper option but it is not as good as the Lamello system. Knapp connectors are biscuit like in that you cut the slot with a normal biscuit machine and then slide the connector in and it is a knock down system as well.
Great explanation!. I am thinking to buy one of these machines and considering I still can use dowels I may opt for the Lamelo for the same reasons you mentioned, the festool way seems to carry risk and a lot of messing about once you get to the job inserting all the bits
Interesting video - thank you.
That was very helpful, thank you
Great explanation Peter! my biggest gripe with those Festool fixings is the size of the hole needed and also the very cheap plastic covers that remind me of a cheap MFI kitchen back in the day or flat pack Ikea furniture. I do love using the dominos and was my main purpose buying the 500. Pretty excited about the Lamello as I managed to find an almost new one yesterday with the Tanos kit inc the Clamex, Tenso and Divario fixings. Best of all its the 50th anniversary model, braggers rights model lol. Looking forward to building my own kitchen using this system.
NiceI 50th anniversary model,is the one I have, Diamond blade is fantastic when you’re working with more abrasive man-made boards! 👍
Excellent vid with awesome imagery - well done again. For me the Festool Domino will get far more done (the Connect system is an extra, an addition) but for it specific purpose then the Lamello wins by quite of a margin. One tool only? Festool Domino. Can justify and afford two tools? Buy the Lamello as well. The Connect system is also more environmentally friendly: most of the system relies on metal whilst the Lamello is mostly plastic...
Thanks Peter. For assembling bed leg ends to a frame, I wonder which would be better ( strength and creekiness ) over time.
Hmmm. Now that I’m not so sure about. I know the Clamex are rated at ~80Kg per fitting, so they’d probably be OK. I wouldn’t fancy the Domino’s chances - better off with the bigger connect fittings in the DF700 I think! 👍👍
Very concise content. Good job.
Thank you! 👍
Great video. Thanks for doing this. As a fellow CZcamsr, I have to say that you have a wonderful screen presence and style.
Thank you! 🙌
The Zeta for me. It's a great tool!
I think the connect still,has a place, but the clamex are excellent 👍👍
Many thanks for making this video. I'd first seen the Lamello on Joey at kingpost timberworks' channel, and was very fascinated. Great to see the side by side comparison - I think you and Joey might have to split the commission that I'll shortly be paying Lamello.
Haha - I’ll babe sure to take that up with Joey! 🤷♂️👍
I’ve long owned a lamelo machine love it it was a expense to purchase but I cannot remember how many times I’ve used it over the last forty years I’m not opposed to knock down hardware but there constantly remains the problem on hiding the fasteners i e looked at the domino machine and questioned how much I’ll use it but I’m sure I’ll convince
Very well done video. To the point, and you speak quickly enough so I don't have go to 2x speed! Thanks.
Haha, thanks! 👍
Love your shirt.
For sure each one is not replacing the other one. It looks like the best scenario must have them both
Being on the Festool fb group I know the lamello has won this war 😂. Haven’t used one, but neither have I even bought domino connectors for my df500 to try out yet. The only improvement for the lamello that’s been raised is...reference pins and I think a slight price drop, but why would they when they know it’s the better machine for a similar job. Great video as always, eagerly awaiting the next cnc video though 😉🙂👍🏻
Thanks! The CNC has - literally - been put to one side while I get on with some work stuff, but I'll have it finished before too long... 👍
Thank you for sharing this, the Lamelo looks good but I won't be buying one as I don't need one but if if I was building furniture for a living would definitely go with it
You better ask for the high price because buying the consumables of the zeta can cost you an arm or a leg ...
Thanks Peter, that's made my mind up. I think when I saw you previous vid that Lamello was taking the biscuit, so to speak. The king is dead ......
I think it’s more nuanced than that tbh,; having spent a week or so working on very narrow section stock, I think the Domino is a more flexible system overall- it the Lamello wins hands down did the KD fittings and cabinet/carcass construction. Not an either/or decision, I think. 🤷♂️👍
I own prefer to use Lamello Zeta P2 Clamex connectors in conjunction with Domino DF 500 4x20 or 5x30 tenons. This way you can get best combination of strength and versatility for joints. Loosen tenons take all mechanical pressure and Clamex connector provide great clamp pressure between parts with ability to detach on demand.
Thanks, yes, I’ve used them a few time’s now, they work well together. 👍👍
Good explanation there Pete , I don't think I'll ever be using either system, but from an engineering point of view I was interested in how they work... & I always drop in to give yer vids a like ... 😎👍☘
Haha, thanks Peter! 👍👍
You also forgot about the Festool C 18 cordless drill you need to take that large drill-bit for the hole in the boards face (where the tightening screw emerges for your screwdriver to grab a hold of).
Very good !!! Nice video and explication!!! 👍👍👍
Thanks! 👍👍
I have a domino machine and was wondering when they would finally develop a fixing system. Now that it is out, I am generally disappointed with them and find them weak. My partner has a Lamello, and that is what is being used in our workshop combined with domino wooden pegs. The combination gives a very stable and sturdy finished furniture.
The Clamex is a awesome connector but the Festool Domino allows you to do narrower joints ie. Rails etc
They both have their place... Nice video...
Exactly. Can’t have just one. 🤷♂️👍
Totally agree! When people compare a biscuit joint and a domino joint; I always describe the biscuit as a loose tounge and the domino as a loose tenon. They both have their benefits, and applications.
the Clamex is a work of genius
This is an awful good and honest review Peter. Even a green heart has to get somewhat red sometimes - herein we both agree. A lot of people make reviews but you Peter, nails it and brings everything down to an easy to understand conclusion. 25 mm and easy to ship. I think Festool have to buy the two annoying red companies down south after all - if you can beat them for goodness sakes buy them and paint them green 😜💪❤ Cheers mate 🇩🇰
Haha, thanks Henrik! Always a place in my workshop - and my heart - for the Domino, but the Lamello has a lot of appeal for cabinetry. Look forward to using it in earnest soon. 👍👍
It's an impressive bit of kit, the P2, with how it cuts the slot. The price is eye-wateringly expensive though. No doubt for someone in the game though, it'll quite quickly make its investment back in saved time.
Hope so! Keep you posted... 😂😂🤷♂️
def not for the amateur - makes festool look cheap
.
Thank's Peter for another good insight into the two systems, unfortunately as a hobby woodworker both are way out of my price range, the only price I've seen for the Lamelo is £1350.
Cheers Steve. If you shop around a little you can get the Lamello a bit cheaper, but yes, it’s getting on for twice the price of the Domino. 🤷♂️
Thanks!
Thank you! 🙌👍
Nice side by side comparison, mate. 👍
Andy over on Manor Wood did a strength test on the Lamellos a few months back, and man they are surprisingly strong.
I think he may have bent a clamp trying to break a joint...
Cheers Bill!. The clamex are almost stupidly strong, yes. 👍
I was wondering how strong they are, as biscuits are far weaker than Dominos.
I’ve noticed you’re creeping up to 40,000 subscribers Peter😀. I read somewhere on the internet (so it must be true) that it is customary for cabinet building / carpenter CZcamsrs to giveaway a Lamello Zeta when they hit 40k so don’t forget good sir😀
Well fortunately, I have just such a machine at my disposal, Leo... 😂😂👍
184k and more
I have both. I would say I feel the Domino connectors are a bit more substantial I have used them in much larger pieces where they are a significant part of the structural integrity of the piece. I've only just got the lamello and absolutely love the tenso for mitres it's so simple and no clamps necessary just the connectors and a bit of glue. But I don't think I would trust the clamex if there were too be a lot of lateral force placed on the connector. It just doesn't seem as strong as the Domino connectors.
They both have their place, and the domino connectors can be used in eg narrow stock, where the Clamex is much more useful for sheet materials. I’ve never had an issue with either fitting, but the connectors for the DF500 feel like much more of an afterthought compared with eg the connectors for the XL. 👍👍
Good video Peter...I would not say there is a winner......at least Festool makes again stronger joints so they stay true to their ground (although in mdf it probably does not make a lot of difference) That being said Lamello is a quick/easy and quality solution in a lot (the majority) of situations.
Thanks Erik. I agree, no real winner, though the clamex is undoubtedly the more elegant solution, the Domino connector will fit in much narrower stock. So you have any reference to the relative strength of the connector system? I searched quite a bit before I made the video and couldn’t find anything about the holding/ clamping force it applies. The clamex apply 80Kg of clamping force, just FYI. I’m certainly glad to have both options for the work I do. 👍👍
Just rewatched this video after listening to your discussion with Andy on “measuring up” and you can really see how much time the lamello must save you.
Using it for the first time on a job today. So far, so good 👍👍
How did it go? How much time do you think it saved compared to the festool?
@@MrBishbashbosh2012 Still on it. Taking it slow and steady as I'm breaking the cardinal rule and using a new tool on a job. I'll have a proper comparison of the two systems out in a little while. 👍
Sounds good, I look forward to it.
I agree about the Festool connectors. I like the engineering behind them and the "Trilobite-like" shape of the gripping end is cool (biomimicry!) but for practical purposes the same issues make nervous both in terms of transport but also user end issues. On the surface I like the Lamello approach which is way more conventional. Goes to show the fancier more cerebral approach isn't always the best solution. In fact, one issue in general with the Domino 500 is the lack of a proper grip. It may sound strange but a lot of Festool tools lack surfaces that are grippy where they need to be and ergonomic. It almost feels like they opt for a more minimal look as opposed to proper form following function approach. For example, the 1400 Router on the stick handle has no grippy surface just smooth plastic. Picking it up quickly and feeling the weight of the machine tip forward and down, while, holding onto a smooth surface is not exactly best practice. I enjoy my Festool tools so don't get me wrong but with so many simple oversights I often look at Mafell as still the more user friendly of the two. I just wish here in the US their presence was greater.
Yes, agree about the ergonomics & the lack of ‘grippiness’ of many Festools; no joke as people age, and grips get weaker. I think the ergonomics of the bigger domino is better, and the small one is long overdue for a makeover, I think. 👍👍
@@10MinuteWorkshop back when that Core77 article came out they said Festool had two designers and over 20 engineers I believe. One of the designers had been there for many decades while the other was right out of grad school who I guess did a Festool thesis project etc. Anyhow from a design perspective one would hope to have more designers per engineer than that! I have a whole list of easily 3D printed items as simple accessories to make the 500 and some of their other tools more user friendly. Maybe one day I will get around to making some of them. But could someone make a nice solid aluminum mount for the 1400 on the track please? The plastic one with the metal rods doesn't cut it.
The Lamelo is a stunning looking but of kit. Looks like a huge time saver too. Love it...
Blue point bit driver Peter? Not been near the dreaded Snap On can have you....🤣🤣🤣🤣
No, that bluepoint is the closest I’m getting... 😬👍
@@10MinuteWorkshop probably best... I still have all my old bits... and the wallet dent to prove it... 🤣🤣
nice review, I been using the XL connector a fair bit and really like them ... how would the festool connector work in particule board type panels (19mm) ?
Thanks! I've never used them in particleboard, but I'd expect them to be fine; used them in MDF without any problems. 👍
Good comparison video Peter. Lamello wins hands down in my opinion .
Thanks! Don’t disagree, but the Domino is so versatile, especially on narrow stock. Room for both, I think! 🤷♂️👍
I am planning to use the Scheulenburg Connector with bei Mafel Dowler
Hi Peter!
Great video and great explanation on pros and cons.
I have just received the domino connectors set and I was wondering if I could use it with chipboard (melamine) panels.
I think I saw a demonstration with the Lamello Clamex but cannot recall a single demo with a Festool Domino connector.
Would that be possible?
Thanks Harris! I think a lot would depend on the chipboard - if it’s a good quality MFC e.g. Egger then you’d, shouldn’t be a problem at all. I’d run some tests before using it on a job though! 👍👍
It's funny you would post this today, I was at the Festool roadshow on wednesday morning and saw this. It was very impressive. But the domino is way out of my price range at the moment. Let alone buying the fittings kit :P
Peter has a second-hand one he might sell you! 😉
Sadly I couldn't afford any price right now. Otherwise I would take him up on that :)
@@MrMasterbiker I too have been through rough patches in my life, particularly financially. I hope things pick up. Good luck! 👍
Thank you!
I never leave the tenons in. They don't need to be screwed in firmly to work. I know it's counter intuitive. The tightness of the join comes from the set screw correctly positioning itself in the hollow side of the tenon which has the effect of pulling the tenon slightly up and creates the needed tension.
Politely disagree. I was borderline paranoid about over tightening them when I first had them, and as a result the pins weren’t driven fully home, and the joint didn’t pull right. In my experience they have to be driven in fully. 🤷♂️👍
Politely disagree. I was borderline paranoid about over tightening them when I first had them, and as a result the pins weren’t driven fully home, and the joint didn’t pull right. In my experience they have to be driven in fully. 🤷♂️👍
@@10MinuteWorkshop Fair enough.
@@10MinuteWorkshop I overtightened one once and had it snap, I agree with Muru Roa on this.
Handy video.. as usual 👍👍
Very nearly sold on the Lamello. Will you be doing a video on the different Lamello connectors soon?
👍
Thanks! IfI find myself using any others I'll certainly do something, but I think the Tenso and Clamex will cover an awful lot of situations. 👍
If I was smart enough to invent these joiners, the Festool would be Mark I and the Lamello Mark II. The higher the Mark the better the device. So now I know another tool that I have no use for. Got to go now, got to look on eBay and Amazon for the best price on the Lamello.
The original knockdown furniture was campaign furniture. For a long time I have liked the aesthetic and really been in awe of the skill of the builders. It reached its best at the height of the Empire. Sorry Peter absolutely no mdf or dominoes and entirely done by hand. Reasonable wiki entry [it was used by the Egyptians (who probably took the idea from someone else)] but not correct in claiming it as a Roman invention. If anyone decides to do a modern project video I would love to see it.
There is a comment from someone with a son in the military I will try to post a more specific post in reply to that.
The Festool solution leaves holes that look remarkably like those on Ikea furniture. Not a huge selling feature to a client whose just forked out several thousand for fitted units. Just sayin ....
Yep - one of the reasons I haven’t used it much. 👍
+Alan Morris
Most customers would not even notice that they are there to be honest. Woodworkers and crafts people sometimes do not realize that the average customer is not so switched on to small details like that.
I'd say for most fitted units the holes would be on the outside so they will never be seen. Both tools have great benefits. The lamello definitely wins in the knockdown department. Where the Domino is only a passing grade. I think the reverse is true for structural connections. The domino's ability to replace traditional mortice and tenons and with such incredible strength is it's most significant benefit. I wouldn't even trust the 14mm lamello biscuits to do the same.
Do you leave the fittings out until after painting? Just dry fit with regular dominos? What about for the Lamello?
Yes for the domino connect, as for the lamello, almost certaoinly, but if you've seen my videos then you've aseen every joint I've made with it, lol! I'll know more when I use it more. 👍
As a fellow festoolian. I’ve played with festool connectors, still prefer to glue regular dominos whenever possible, never played with lamello.
Question? From what I gather here it’s almost same as biscuit jointer cut style.
And the way lamello fixes itself to material is by applying pressure towards skinny sides of board. Potentially splitting the board? As with festool, it always applies pressure towards small sides of mortise (along the length of material) meaning it’ll almost never fail?
Which also tells me it’ll still be stronger connection in stuff that is skinnier then 3/4” or 25mm in thickness. Or when you work with laminated plywood? Not mdf
What’s your take on the strength of the connectors?
The Lamello connectors are immensely strong - the Clamex apply 80 kilos of pressure per fitting - so yes, just like with dominos there’s the potential for the material to split of pressure is applied in a way that the joint is stressed eg racking a corner joint, especially in eg MDF. But in practice this has never been an issue as once the backs are fitted to a carcass the structure is pretty ridgid 👍
First Class.👍😀
Thanks Norman! 👍
Hi Peter, Great channel thanks for all your effort you put in to produce such good content.
A question for you, what is the hinged mechanism you have on your crosscut track, i don't know if you have produced a video that covers this?
Many thanks
Martyn
Hi Martyn and thanks! The hinged rail is part of the Festool MFT (Multi Function Table) that I have - I talk it in videos #182 and #183 👍
@@10MinuteWorkshop Thanks Peter i will check out the videos 😁
It seems like the festool connect would provide more strength, what is your opinion on the strength of both options?
The Clamex is almost ridiculously strong. I’d have no qualms about using either, in that regard. 👍
I never thought there would come a day when a festoolian would think, I can't justify the price of a Lamello Machine. Haha. How things have changed.
I've always loved Lamello - they make festool seem cheap... 👍😂
Lamello makes quality stuff. I have a Lamello biscuit joiner, in the hand it feels like it's a step above any of my festool tools.
Great video as always thanks ,haven't saw this asked yet. so if you were to recommend buying the lamello or festool domino if you had neither to begin with, with your knowledge now for overall usage which would you pick?
That’s such a tough question - though one I’ve touched on in the podcast. For the bulk of the work I do, then I think the Lamello would be the better choice, though I think the versatility of the Domino makes it a better general-purpose machine. I’m glad I have both, let’s say. 🤷♂️👍
Peter Millard well, they’re really for different situations. The Lamello is great for knockdown furniture, but the domino is good for glued up assembly, and can be used for knockdown with the connector kit. Can the lamello be used for glued connectors too?
Do you add glue to the joints before final assembly at the client's house? Assuming you don't want to take them apart ever again.
Yes. In that instance I’m using the KD fittings as permanently fitted clamps. 👍👍
Pete excellent video will the clamex2 products work with any other biscuit tools?
Thanks! These Clamex connectors will only work with the Zeta, but I believe there are other fittings that will work with a regular biscuit slot, though my understanding is that they need to be screwed in place. 👍
soo cool. My question is though. will any of these tools do as small as 12mm ether MDF or Ply? thanks :)
Yes, they both will - though more completely with the Domino. 👍
I guessing the 25mm extra than the Lamello is more of a concern with shelving type joints rather than top or base joints as they can literally be on top of the sides, I am rushing so this might not make sense
Makes perfect sense - though I always set my top/base between the sides of the carcass 👍
Would either of those systems be suitable to use without additional wood glue? For example on floating walnut nightstands.
Yes, they’re both designed to be used ‘dry’. 👍
I currently use biscuits and screws for my carcasses, so may be missing something here. Looking to change to one of these systems so any advice appreciated.
If you are working in a tight space why can’t you make up the carcass, then slide it into the alcove. Then there’s no issue if the connectors stick out by 25-50mm before assembly. Also, can you not put the access holes on the exterior of the cabinet, so they are hidden when fitted, or does the Festool setup not allow you to do that?
Thanks.
Sometimes you have to build something in situ - where access is too tight to get to get a fully assembled carcass in, for example - and not having to allow for the spike on the connect can make all the difference. 👍
@@10MinuteWorkshop Thanks for the reply. I've always found that pre-assembling helps when getting units into tight spaces. It sounds like you have a great deal of experience with these things, so will wait until I hit the problem before I decide if I'm right or wrong!
For installing into a tight space, comparing these two systems, Lamello seems to require only 4-5mm spacing to get your pieces into place. Is there another Lamello that requires even less space? Thanks for the video!
Yes, that’s the gist of it. If you need less space then one thing you can do is to remove the nubbins on the Clamex and just rely on the pivoting tongue. Obvs. you have less lateral strength, but they’re still very strong. An alternative may be something like the divario fittings, but they’re a different animal. 👍
Hi
I see you used MDF how much force would it take to pull the joints apart because it seem that you fix both sides one one set but no the other you just seem to slot one side in the slot and the other you drill whole to join together if you get what I mean
I don’t know wrt the Domino connect, but the clamex needs 80Kg, so plenty strong. 👍
Very informative, i always thought the domino and zeta p did the same job, but the difference is quite clear. Why do you use that extra fence on the zeta p? Or is it part of the tool? I just own a lamello classic x
Thanks! The extra fence is to add stability when you’re making a cut into the face of the board, - it gives a guaranteed 90 degrees 👍
@@10MinuteWorkshop ok, good to know, thanks Peter!
Hi Peter, interesting comparison, clearly the Lamello wins on simplicity of implementation. Would the joint and by extension the carcass being built be as strong as if it was done using the domino system?
Hiya. Yes, the Clamex in particular are almost ridiculously strong. No issues there at all. 👍
Great video as always but... I’m confused. What’s preventing you from putting the tenons in the edge vs the face? You’re just changing boards where you drill the mortises and the hole for the nut
Thanks! That’s just not how they were designed to be used, and if you wanted to try it you’d need to be making carcasses from much thicker boards as the connectors are too large for the standard 18mm. 👍👍
An interesting pair of couplings but is the metal option stronger than the plastic one? Clearly the simplicity and size of the Lamello is far preferred but it does appear to remove more material to fit. Also, how do the materials costs compare, temporarily ignoring the time element? Another engrossing video though, thanks!
Thanks! I haven’t been able to find any information on the strength of the Domino connectors, but the Clamex exert 80Kg of clamping pressure so I’d expect them plenty strong for the kind of cabinetry applications I’ll be using them for. You make an interesting point about the material removed, but while the Lamello may take more away, the forces are spread across the whole of the fitting (both sides) whereas the domino connect seems more reliant on one half of the fitting getting its elbows out. Fittings are ~£1.60 (domino) vs ~£1.20 (lamello) though bulk buying may reduce this a little. 👍
Hi Peter, did you give any consideration to tiga tool domino connectors. They look far simpler than festool. Never tried but I would be interested to see your take on them:)
Great channel, thanks for all work on the content I know its massive much appreciated.
Hi Mateusz , and thanks! I had a look at them back when they were called ‘Dominofix’ and though they’re a neater system than the ‘official’ domino connectors - and they were available for the df500 before them too - I just didn’t like the idea of needing to screw everything together tbh. Never managed to get my hands on any, so I don’t know how strong they were in reality. 🤷♂️👍👍
Where did you get the black stop from that you use as the fence for referencing? Many thanks
Hi. Sorry, not sure which ‘black stop’ you mean?? Was it on the Domino at 4:54? That’s a Domino-plate from Seneca woodworking - takes away any fence drift, and gives additional support. 👍 Domi-plate UK: amzn.to/2PffzFE (US: amzn.to/2QU1mi9)
That’s it, thank you
Peter, i wish to make a long entertainment unit that will require a mdf or plywood benchtop longer than available stock. Would you recommend either of these to join lengths end to end? Regards, Jeff
Thanks Jeff! Either would be fine, but my preference would be for the Lamello Clamex. 👍👍
Thanks
Peter, Great Stuff, what MDF is that your using?
Medite MR MDF, always 👍👍👍
@@10MinuteWorkshop Thanks
I think it bears mentioning that whilst Lamello's connection is a better system in your opinion (I don't have a foot in either camp) if you had neither tool - the Domino or the Zeta, surely one would buy the Domino. Despite the connection system not being quite as useful, the Domino is a vastly more useful tool. Can you imagine running your shop without it and what tool do you remain to pick up more often?
Yes, indeed: this video was - as per the title - specifically about these connectors. I think the Domino is a more versatile tool for general use, but the Lamello wins for sheets goods/ cabinets/ carcasses.
Regarding transport of panels. Could you just remove the Festool pegs and refit them on-site? That would get them out of the way and remove the danger of bending/breaking one. Another question. How does the Lamello cutter make that shaped slot? Does it move up and down to put the under cuts in?
As said in the video, the pegs would need to refit exactly to ensure a solid fit, and I’m not convinced they would. Re the Lamello, see video #325 for a slo-mo of the action. 👍
I thought you meant the whole thing, not just the protruding part.
25mm either side=50mm in my book Peter! Still it's Friday,end of week,may let you off again!😀👍👍👍👍👍👍👍👍👍👍👍
Fit one side, move carcass.
@@bobuk5722 but then all the weight is hanging off the fittings on one side!
Yep, I’m a fit one side ata a time man, myself 🤷♂️👍
Could you use the lamello to attach face frames to the cabinet? How much are the lamello connectors compared to the domino connectors? I like that lamello. I think I would buy that over the domino
Yes, easily. The fittings in this video are ~£1.60 a set for the Domino, and ~£1.20 for the Lamello.👍
Lamelo seems far more quicker and better looking. If i had the money i would buy it
Another reason to consider lamelo is thats its also now available in cordless. I don't think the domino is.
Its a pity the lamelo doesn't have the spring stops like the domino
I’m a bit of a Festool fan but on this occasion I think that Lamello have a cheaper and more elegant solution.
Yes - although the price difference between the Domino and Zeta machines would buy you around 1700 Domino connectors! 🤷♂️👍
I just want to know how the lamello is able to cut that slot with the relief cuts on the sides. You plunge it in, right? How does it not make the entire slot that same size? Is it moving the blade up and down when you get to full depth?
See the previous video on the Lamello #325 - you even get a slo-mo of the cutter in action 👍👍
@@10MinuteWorkshop Oh cool. Thanks. I'll check that out.
I think both connectors are good but you might have to think more ahead with the domino connector.
Yes, absolutely.
How does the Lamello make the T slot? What is the blade profile?
It's a T shaped profile; the blade does a little jump up/down when it gets to the set depth to make the T-slot - if you have a look at video #325 i explain it there and show a demo of the action in slo-mo at about 4m 30s. 👍czcams.com/video/5EuXJo0pHso/video.html
I think it's quite clear that the Clamex is the superior product, like you say, it looks as though the Domino Connect was a complete afterthought. And that cover for the hole, it's atrocious!
It makes the work look so cheap!
I think what we need now is for Andy to do some strength tests to see which is stronger!
Haha, he only does wallplugs these days. 😂
@@10MinuteWorkshop He's got to fulfil those Fischer sponsorship terms! 😂
@@animationcreations42
He is free to do as he pleases. Out of curiosity do you work or are you sponsored by an opposing businesses? (you are not part of an anti marketing team?)
just change your cutter head on your regular lamello to 8mm thick, and use their older clamex S system, no need the Zeta system. it adds 2 screw into each side of your substrate for holding strength too..
This is the only Lamello I own. Never had a biscuit jointer before. 🤷♂️
@@10MinuteWorkshop haha. i guess my remarks are for those who cant yet fork out for a zetap2 yet. yours truly included.
You say that you didn’t like the fact that the domino connection sticks out 25mm making it not a snug fit in say an alcove. Don’t forget you would have the other side the same so the unit would be about 50mm narrower overall. Or am I missing something.
I'd generally fit one side, then the other, so you'd need the width of the completed piece, plus 25mm. 👍
I am looking to buy the domino DF 500 for it's versatility. I was wondering what that accessory you have attached to the base of the machine is called? And where about I could purchase one?
Is it the Seneca Domiplate?
It is. 👍
@@10MinuteWorkshop great, thanks!
I would like to know what the strength is of those connectors if you join two sheets of plywood together and put weight on top of the seams
Festool don’t publish load ratings, it the Clamex are almost stupidly strong - around 80Kg per fitting.
@@10MinuteWorkshop I'm trying to decide if joining it with a climax would be better than pocket holes essentially two shelves butted together
Lol ‘Knocked Up’.
😆
I have the whole shabang from festool, but i have to admit that i like lamelo's idea more, and the best thing about it 's the smaller holes for the hex key , the festool ones are really ugly, especially those plastic caps , that's why i always try to put them in positions that will unable you to see them . But it's too late now , i'm not spending another thousand .
Yeah, that’s what I said. And then I did... 🤷♂️. Clamex is such a great connector, but there’s always space for a domino 👍👍
Seems like the festool connectors would be significantly stronger, which may or may not be relevant depending on the application.
The Clamex are almost stupidly strong - something like 70Kg per fitting. Festool don’t publish load ratings, unfortunately. 🤷♂️👍
@@10MinuteWorkshop Damn. That's a lot for those little nubbins!
The little nubbins just locate the fitting, the strength comes for the cam-shaped lock that tightens in the slot. 👍
@@10MinuteWorkshop Ahh, I see. Thanks for the clarification! I'll just stick with my domino, but I don't do much cabinet work, so really no need for knock down fittings. Interesting video nonetheless. Thanks again!
Definitely the lamello fittings, there a lot better. faster and a better end result and no need for finishing caps to hide the fittings.
you still have the holes (though smaller) , just nothing to cover them.