Just wanted to say I ran the grounds just like you did and it’s running amazing. Replaced the throttle body, the throttle body sensor and the MAF sensor before doing the grounds and it works perfect
I've been a mechanic for over40 years. I've worked on just about everything. With that being said I also used to work on fire truck for the air force. The alternators often put out over 300 amps. There have been a few times that I would have a voltage drop between the alternator case and the engine block that it was mounted to. It would loose some grounding Thu the bolts and brackets. I would connect a ground cable from the alternator case, engine block and body of the vehicle. This would give me maximum charging and prevent my gauges and lights from dimming and give bad readings. Hope this helps. By the way the battery in the Tahoe should be reading 12.6 volts not 12.2 as I saw on the post. You probably have a battery cell going bad or the battery needs a charge. Enjoyed your posts, reminded me of the good old days. I know what you mean about getting older. Hard to get anything done.
Is there a chance of creating a grounding loop by adding extra ground wires? I was about to do what this man did in the vid, but then I read about grounding loops. Any thought on that? Thank you.
The code can be caused by a faulty throttle body, TPS sensor, as well as a few other sensors. The ground problem is easy to fix, I removed the engine ground and grounded the alternator body directly to the battery. I also am using a top post battery with military terminals!
Good to see you out and about there Bear! There are GM Bulletins on the Throttle Body issue. If this didn't fix it, at least you will know for sure that it is not a Ground problem. I would coat all the newly exposed surfaces and the wire terminals with either dielectric silicone grease or second choice, fluid film or Zep 2000 clear spray-on grease. Anything to slow corrosion from re-occurring. Now go inside and treat yourself to some hot coco! Hopefully you will be warmed back up enough to do the live show later on. I hope SC is feeling better too. Take care Bear and God Bless you my friend.
I'm having a similar issue....I damn near changed everything on the truck...might ride perfect then get hit with stabitrack/reduce engine power...shit truck off 5minutes back to normal....does this a lot ...I ran a new ground from engine to alternator, ran good for 20 miles then it's back..🤷🏾♂️ I don't know what to do any suggestions? The truck is a 2009 Tahoe 5.3 Ls
we finally ended up replacing the throttle body. its been running great now just did it 2 weeks ago. she also said since i replaced it she says its shifting better now to. hopefully it helps.
Dirty oil will throw it into limp mode also . I only mentioned it cuz i been there and done that also you dash says to Change oil . Remember to reset the engine oil life on the computer
Hey man where did you mount the ground wire to on the computer exactly? AKA the other side of the ground wire you mounted that’s near the engine block (near the alternator). Please I need help!
Its possible for the connector at the throttle body to be an issue. If you have a live data stream from the two throttle voltages, wiggling the connector can sometimes cause that voltage to change, which isnt good
Could a low batter cause this becasue I've added the grounds amd mine continues to do this. My fuel pump died on me and after replacing fuel pump,filter and throttle body I've had nothing but issues t keeps throwing the tac module code. Which think is p1516 code I can clear and it'll run fine until I have to slow down r stop to idle
Great video. Couple questions. 1. How did you modify that battery cable? Did you cut that rubber out with a knife? 2. Did you clean your grounds with a wire wheel attached to a drill or something?
Hello I'm having a problem with the knock sensor in my 2003 GMC Yukon XL 2500. I've changed the original sensor, wire and refrigerator face three times, yet the Check Engine Light is still on. The codes that appear on the scanner are P0300, P0332, and P0327. I also changed the spark plugs with the wire, and used #41-110 spark plugs as recommended by the parts store, even though the recommended spark plug number for my car is 41-962 according to the chassis number. I would like to know if the problem may be caused by using #41-110 spark plugs instead of 41-962. Please let me know as soon as possible. Thanks
Sweet! Did it yesterday along with the under driver's side ground. Pretty sure my throttlebody is burned out tho. Not throwing code but throttle has dead spots
You dont show when you connect the grounds to the bracket on the altenator, and you just point to the computer , dont show how and exact bolt u un screw to connect to the tcm, kinda fishy
Just wanted to say I ran the grounds just like you did and it’s running amazing.
Replaced the throttle body, the throttle body sensor and the MAF sensor before doing the grounds and it works perfect
I've been a mechanic for over40 years.
I've worked on just about everything.
With that being said I also used to work on fire truck for the air force.
The alternators often put out over 300 amps.
There have been a few times that I would have a voltage drop between the alternator case and
the engine block that it was mounted to.
It would loose some grounding Thu the bolts and brackets.
I would connect a ground cable from the alternator case, engine block and body of the vehicle.
This would give me maximum charging and prevent my gauges and lights from dimming
and give bad readings.
Hope this helps.
By the way the battery in the Tahoe should be reading 12.6 volts not 12.2 as I saw on the
post. You probably have a battery cell going bad or the battery needs a charge.
Enjoyed your posts, reminded me of the good old days.
I know what you mean about getting older. Hard to get anything done.
Is there a chance of creating a grounding loop by adding extra ground wires? I was about to do what this man did in the vid, but then I read about grounding loops. Any thought on that? Thank you.
The code can be caused by a faulty throttle body, TPS sensor, as well as a few other sensors. The ground problem is easy to fix, I removed the engine ground and grounded the alternator body directly to the battery. I also am using a top post battery with military terminals!
Thanks for this video!! Far behind helpful than any vids on you tube!!! Very detailed information 👌🏼 👍🏼
Glad it was helpful!
Good job! Want to give ya a big hug!
Thank u for your help i am having the same problem samething as you am goin to do tjis and prsy it fixes my problem
Tanks for the video my friend
12.1v, the battery needs charged and checked. This code also pops up with low voltage as well as the p1518 TAC module code
Good to see you out and about there Bear! There are GM Bulletins on the Throttle Body issue. If this didn't fix it, at least you will know for sure that it is not a Ground problem. I would coat all the newly exposed surfaces and the wire terminals with either dielectric silicone grease or second choice, fluid film or Zep 2000 clear spray-on grease. Anything to slow corrosion from re-occurring. Now go inside and treat yourself to some hot coco! Hopefully you will be warmed back up enough to do the live show later on. I hope SC is feeling better too. Take care Bear and God Bless you my friend.
Yes im going to the show. It did warm up good.
I suggest using that battery terminal protector spray to seal the grounds
I'm having a similar issue....I damn near changed everything on the truck...might ride perfect then get hit with stabitrack/reduce engine power...shit truck off 5minutes back to normal....does this a lot ...I ran a new ground from engine to alternator, ran good for 20 miles then it's back..🤷🏾♂️ I don't know what to do any suggestions?
The truck is a 2009 Tahoe 5.3 Ls
we finally ended up replacing the throttle body. its been running great now just did it 2 weeks ago. she also said since i replaced it she says its shifting better now to. hopefully it helps.
did you replace the throttle body with a oem one?
Dirty oil will throw it into limp mode also . I only mentioned it cuz i been there and done that also you dash says to Change oil . Remember to reset the engine oil life on the computer
Good job worked for me
Glad I could help
good to see you fixed it
Thanks
I'm going to check my Body Ground that you showed u cleaned and see if it helps stop my battery from draining every couple days
It might help won't hurt
Mrs bear can i use 4 gauge cable to ground!?
Thank you
good info bear
Thanks
Hey man where did you mount the ground wire to on the computer exactly? AKA the other side of the ground wire you mounted that’s near the engine block (near the alternator). Please I need help!
i used the upper corner of the computer towards the fuse box. just a note we did end up replacing throttle assembly a few months later tho.
👍
Its possible for the connector at the throttle body to be an issue. If you have a live data stream from the two throttle voltages, wiggling the connector can sometimes cause that voltage to change, which isnt good
yes that could be another issue.
Thanks i will try to add grounds.
All the best
What size gauge ground wire did you use? Thanks in advance!
i think it was a 10 gauge i think.
Shouldn't you be cleaning all grounds to chassis?
yes it should be, but time and weather limits i had the time to do this repair and she says its running better then before and no issues yet.
Could a low batter cause this becasue I've added the grounds amd mine continues to do this. My fuel pump died on me and after replacing fuel pump,filter and throttle body I've had nothing but issues t keeps throwing the tac module code. Which think is p1516 code I can clear and it'll run fine until I have to slow down r stop to idle
yes if the battery is not holding a full charge it could be making it mess up.
Great video. Couple questions.
1. How did you modify that battery cable? Did you cut that rubber out with a knife?
2. Did you clean your grounds with a wire wheel attached to a drill or something?
i used a utility knife and cut the rubber to fit. i have a small loc dis that i used to clean the metal.
@tlcbear2 OK thank you!
Hello
I'm having a problem with the knock sensor in my 2003 GMC Yukon XL 2500. I've changed the original sensor, wire and refrigerator face three times, yet the Check Engine Light is still on.
The codes that appear on the scanner are P0300, P0332, and P0327.
I also changed the spark plugs with the wire, and used #41-110 spark plugs as recommended by the parts store, even though the recommended spark plug number for my car is 41-962 according to the chassis number.
I would like to know if the problem may be caused by using #41-110 spark plugs instead of 41-962.
Please let me know as soon as possible.
Thanks
sorry for not seeing this sooner. might need to verify wires to make sure its communicating with computer.
Can you help me with my 2016 suburban it turns on but nothing is starting had in the shop and they could fix it either
What all happened
Tahoe 2003 4.8, starts fine but shuts down if I put it on Drive, no check engine though, any thoughts?
is fuel pump working correctly, dirty throttle plate could be a few things but not seeing vehicle in person hard to say for sure.
@@tlcbear2 it was indeed the fuel pump, the pressure was 49 and according to my mechanic it’s supposed to be at around 55/56 at idle
Reduced engine power is starting to happen in my 02 Denali
Hay man I watch your videos my name is Ron I found a 400 sbc 2 bolt main wanna do a 377 have you ever used a dont of 30-30 cam
Yes i have one now. They are fun builds,yes i have used 30 30 cam.
Update, Did the problem come back?
I'm trying this right now
as of now its still running just fine and seems to be a good fix.
Sweet! Did it yesterday along with the under driver's side ground. Pretty sure my throttlebody is burned out tho. Not throwing code but throttle has dead spots
oh cool glad it helped
added grounds did not fix the issue now i am replacing the throttle body
Replace the throttle body and mass airflow sensor as a tandem.
From my experience the reduced engine power is usually a battery issues
You dont show when you connect the grounds to the bracket on the altenator, and you just point to the computer , dont show how and exact bolt u un screw to connect to the tcm, kinda fishy