Video

Super fedt system. Jeg mangler kun at vide hvilken s diode jeg skal købe. Har du et nummer der vil være godt til at lave parallel installationen?

Hello. Can we add a detector sensor to this circuit to monitor BBS? Thus, the LED turns on only when the BBS passes.

I might try something like this instead of buying a $180 tracer unit.

How can I remove the gear without the tool?

Hi Scorpion fans! Thank you for the video! I have an issue with mine, the barrel is wobbling I think, and shots are extremely inconsistent. It is a long version and the barrel is perfectly placed into the silencer. Just for extra information, the barrel is almost protruding out of the silencer, that is how well placed it is. Now, I changed the hop up joint/rubber and even the barrel but I still face the same issue. I even tried with the original barrel but still, I face the same issue. What could be the cause and how can I fix it? Also, where can I buy this spring 0:45 ? I lost mine :/

would you help point me to a full cleaning guild for the scorpion evo? Thanks!

Can you make single shot but binary?

Hej, kan man stadigvæk stille spørgsmål her? :)

this is amazing thankyou so much

nice work

do i must open the silencer to turn on the at2000r tracer every time？can it Start of automatically？

So what is proprietary in the EVO 3. What parts are not V2?

I would love to 3D print stuff like that, but not for tracer, but the flash when i shoot :) Can anyone recommend electronics for that?

3:22 mine came missing with this screw?

Nice video! Do you happen to know what wavelength would work for red tracers?

great content +1 sub, I was wondering if you also had to use a mosfet controller

How do you hide the wires

I need help with an idea how I can talk to you

My bolt release just dangles after I put it together. Any idea why this is happening? It doesn’t work anymore after I put it back together.

suggestion: using a hand scale instead of weights and just pulling and looking at the measured value also: Thanks for the table!

do you have any recommendations for the bb motion detection sensor because I'm going to use an external voltage source.

Quick question Is that coking handle supposed to be out like that? i put a new spring after loosing the coking handle spring and now the chamber doesn’t close properly

Omg ! At the end when u check it, the engine says bip bip and cuts of the power, i have the same problem ! But with a brand new batteri newly charged, but stil have the same problem.... what should i do next ??

Planning to do the last module with 9 leds but decided in roads of 3x3 leds to put on a Airsoft shotgun. Any chance you can help me out? I'm quite handy but haven't really knowledge of electronics...

fantastisk.

what element do I have to add so that the LEDs start only when they detect the passing ball in front of the LEDs? (in suspressor idea)

Is this channel dead?

Is it possible to use a kind of sensor to have it work when bbs fly by just like in a normal tracer as I' want to use it in hpa gun were is no electrics, or at least a blinker/repeter for it to blink when turned on?

What os this gun

Hello sir nice video can i connect this in my trigger assembly as switch of the diy tracer ?

The new king arms m1928 includes a small inline mosfet- do you think the stock one is good enough or would you upgrade it to something better? It also comes with deans connection for the battery but has tamiya plugs from the stock to motor that I plan on changing out to deans

The trigger response is also faster with Dean-T, to the point that you can hear it. Tamiya 2:32 Dean-T 2:50 I went ahead and compared it in Audacity. With Tamiya the average was 0.0923s and with Dean-T it was 0.886s so 4% faster Not amazing... but it's gotta be a bigger difference with LiPo and their much bigger current.

its 14mm?

Are the bbs just regular white or are they special

So if i have a pistol with a positive 14mm threaded barrel this will work? Basically this has the ability to fit both a negative and positive 14mm barrel?

Hi! Thanks for the video. I’ve tried making a suppressor style tracer unit using one 3W UV led. Once tried putting bb through the barrel it glowed perfectly, but it didn’t work once shooting. Can you please suggest the reason of this result? It it because the speed of bb when shooting is too fast for it to glow ?

I was planning on doing a 12 led setup for a shotgun what buck conversion do you recommend and what board did you use to cone t the strip

Hi nice video, can you explain how you time the gears please?

How about heat?

nice videos, I'm love to see first gen of tech guys still working !

Hi there very nice build!! Isn't it going to be simplier if you could you a 3.7v external battery like a 16340 or a CR123a which is 3v, so there will be no need for the converter... ? Cheers :)

Are you using uv lights?

I'm sold! Now to find my weights that I use like everyday...

Make it have some certain modes 1/3/6/--

do i have to raze the voltage by each added 1w UV smd led ?

Do you know were i can order a new full gearbox?

Can we have v3 gearbox We got v3 gearbox at home V3 gearbox at home:

I can’t even get the top off

Hey have u used 1 LED? i have build one with 9 led's inside but the bb does not light up. what kind of led did you use?

What is the unnececary gray thig disturbing view