Video

Hi, my belt is worn and needs replacement. Do you know how to change or can point me in the proper direction?

Wow those are great. What laser is that? I have a hobby machine that's too slow and can only engrave hence asking. TIA.

Where can you buy one? Link?

what is the price of the wattage probe?

I'm waiting for my power meter to arrive So I can test my fifty watt tube.. Guessing it comes from china

Great info and description of what is going on with the lens and focal point but the best I think is how you use your laser to draw your example. That is awesome and creative.

Subscribe

I wonder if i could give myself a tattoo with one of those machines 🤔

Thank you so much :)

Do you lower the head of the laser with a controller, some software, or adjusting the laser bed?

Great video. With an electronic lead screw this makes the process a heck of a lot easier.

Cool! When it was new (Sr90) its shows 20mRh value. (Aprox).

Super 🎉

How do I figure out what tube I will need. My machine looks a lot like yours. Thanks for the video. I'll tell you what's going on. Tonight at the left side of the Tube it started Arching and making a snapping noise. I assume it needs a new tube. Any other Ideas.

I’m at the 3rd mirror. When I pulse I’m getting 2 separate burn holes. Doesn’t matter if it’s close or far from mirror 2. What causes that?

an average multi meter probe will not insulate you properly to 20kv, please be careful before holding things directly touching the 20kv terminal, even if power is off it can still retain enough power for a while to kill you

Curve is down, is this right ?!

Can I use the preforated sheet for co2 laser bed? What is the thickness of the sheet used in your bed?

Can I use the preforated sheet for co2 laser bed? What is the thickness of the sheet used in your bed?

Tamda özel bıçak siparişi verdikten sonra karşıma çıktı video. Teşekkürler.

i have watched a few videos before i found this one,,, thank you so much for making this so easy to do.. others make it so difficult to understand this

Great instruction video. Thank you for teaching me.

wow, there should be an incredible gravity along the ray to make light bend like that...

Clear directions. Thank you

One thing i would like to add is that you need to find a material on which you can see a defined spot. I used paper before and was never able to see a clear circle mark from the laser beam. Now i am using double sided tape without removing the back cover, and i an see a precise mark that makes adjusting a lot easier.

Great instructions. They eased my pain. How horrible was my aligning before this video. Thank you very much for teaching me the right way. (I wish my kids would say that to me at least one time)

IF your machine came with a glass tube from China, it is very important to learn and practice this procedure as you will be doing it often!

Hi, I have the same laser as yours. I'm looking for VENDOR settings, do you have a copy ? Thanks in advance.

Has anyone had experience marking a fresh skin?

I came looking for videos and yours was the second one because the first one didn't look right/seemed too easy. But it is the same and you are doing it the difficult way. Check it out: you just cross over the same colour, then get the other 2 and cross them over under the first 2, binding the previous cross in place. repeat. done. Literally the same as you are doing except you are working on both of the same colour at a time.

I wanna stick my finger under that.

Best video I've ever found on aligning the mirrors. Thanks, you've saved me a whole load of ball ache.

ALMOST great advice.... Some of it is machine independent. As Goku would say, "what is your power level?" Your advice is only good for the specific power of your laser, so what is it?

Tin foil or aluminium foil saves glue gunk getting on your mirrors. Just stuck it to your tape over the mirror. Then keep adding tape.

I recommend woodglut to every beginner and not only.

Dude, why bother with all of this. Why not just do a ramp test?

What softwares are you using for editing pls reply....thanks

Barely getting a 55watt co2 laser and I find this video great to get started on my acrylic work

1:26, light passed trough lens doesn't CURVE to and beyond the focal point. Actually light doesn't curve at all.

in summary..for this machine..a 38mm lens is good for cutting thin metal for example where you need high power focused in a small area..the longer lens is for making straight cuts in softer and thicker material..in between those two is a good general purpose lens..running tests at various depths allows you to determine the focal pont for fine detail work. Thanks for a great video!

Would you be able to tell me what timing belt that is? Mine broke and I can’t find a replacement anywhere online. I don’t have the measurements. I know it’s 3m and 15mm wide but the length of the closed loop is what I don’t know

👽👍

"Trust me, I'm a physicist" famous last words

This tutorial is great. Explaining the difference between position and direction has helped me heaps. SO many other tutorial are just focused on hitting the center of the mirror!

What is the software name for editing

i cut that with 40 watt laser in a single pass. contact me

The tube's terminals needs to be grinded with a small metal-file until the metal is bright/reflective prior installation. So are the wiring's cores, those must show bare copper and be reflective (gently scrape them with a razor blade). This is to remove the highly resistive oxidation from the conductors, ensure good contact, and prevent potentially lethal arcing. #stay safe!

perfect video. Took less than a minute to explain. Cheers !

It looks like I have the same 50 watt laser. I was wondering if you ever upgraded to a 60 watt tube ?

Buenas . Alguien me podría decir sonde comprar esa broca? No logro encontrar