DIY Tukar Thermal Paste Sapphire RX580 | Graphic Card Thermal Paste Replacement

Ex mining grafik card. Test semua ok tapi temperature agak tinggi dan memerlukan fan speed manual 70% untuk maintain bawah 60 degree temperature during 100% gpu load.
********
Ex mining graphic card. All tested ok except for the high temperature and need to maintain manual speed fan at 70% to get below 60 degree temp during 100% gpu load.
Thermal pad
Thermal grizzly minus pad 8
size : 120x20x0.5mm
thickness = 0.5mm
buy here shope.ee/5zzvfSz3hJ choose 0.5mm
Thermal paste
Thermal grizzly kryonout 1g
buy here shope.ee/2fjThDWeDT
*final result manage to reduce temp by 6 degree with similar fan speed configuration.

[@davetan8779]

very helpful video & good camera angle thank u

[@jomdiy]

Glad it was helpful!

[@YAHYA_SUMIGAR]

Mantul....pertama ini. 🙏

[@Lynyryz]

Hallo bang 🙌

[@ahmadfawwaz3235]

could you wash the heatsink run down the water without brake it?

[@jomdiy]

i think better use compress air or contact cleaner spray to avoid corrosion

[@Noname-hr7tv]

Pake thermal pad 0,5mm, sampe sekarang masih aman kah bang?

[@tech4fun477]

how come you dont know the importance of electronic contact cleaner to make your cleaning effectively.

[@cuba8423]

I'm from Poland . I have a Shaphire rx580 nitro + 8gb card. what thermocouples ?? 5 mm or 1 mm or other. I think the same company as you set up, but they are different sizes. how did you work on these ??

[@cuba8423]

0.5 MM or 1 mm

[@jomdiy]

do you mean thermal pad? i'm using 0.5 mm size. i tried 1 mm but the results is i get higher temp during full load.
0.5 mm perform better.

[@cuba8423]

@@jomdiy thanks

[@rushdrift]

the thermal pads should be 0.75mm but its hard to find, you can use 1mm that can be squish but some thermal pads cant be squish enough causing high temp, you can use 0.5mm but the result wont be that good as an oem spec.

[@MrX-yg7rz]

@@cuba8423 część, jakich użyłeś termopadow? Wszędzie zastosowałeś 0.5mm? Tył, ram i sekcja zasilania??

[@rabotnikcexa8188]

0.5 mm is not enough. i would recommend 0.75 mm

[@razmanrhoads2078]

There's no 0.75mm on the market.. just use 0.5mm and u will be fine.. dont use 1.0mm bcause its too thick..

[@razmanrhoads2078]

Idle punya temp lepas repaste dan repad berape bos?

[@jomdiy]

Idle temp dalam 45 bos

[@muhaiminmuaz6458]

bang kalau x guna thermal pads boleh ke?

[@jomdiy]

thermal pad untuk bahagian rom dia, bahagian chipset pakai paste

[@habibimuhammadyusuf3245]

Satu kemasan thermal pad cukup bang ?

[@jomdiy]

sudah cukup, 1 layer saja

[@MrX-yg7rz]

How mm thermopad I must aplicated in this card??

[@jomdiy]

0.75mm original hard to get in the market, the one in the video is 0.5mm

[@MrX-yg7rz]

@@jomdiy 1mm soft have you tried Gelid extreme? What temperatures do you have on 0.5mm?

[@jomdiy]

@@MrX-yg7rz temp during max load 53 ~ degree with 65% fan speed, can reduce to lower temp by increase fan speed to max. i tried 1mm other brand, after few days I notice temp still high, change to 0.5mm now doing fine.

[@MrX-yg7rz]

@@jomdiy all termopads is 0.5? Vram, mosfets?

[@jomdiy]

@@MrX-yg7rz yes

[@a3j4s7]

11:27
Beda before and after.
Before = burem.
After = jelas.
Thanks me later
😉