How to Replace Intake Cam Sensor 01-05 BMW 325Xi
Vložit
- čas přidán 4. 09. 2019
- Buy Now!
New Camshaft Position Sensor from 1AAuto.com 1aau.to/ia/1ACPS00031
In this video, 1A Auto shows you how to repair, install, fix, change or replace a broken, worn out, or damaged camshaft position sensor. This video is applicable to the 01, 02, 03, 04, 05, BMW 325Xi, or similar E46 models.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/o4X/1AXAA00013
• 10mm Socket 1aau.to/oLP/1AXAA00017
• Adjustable Wrench
• Needle nose pliers 1aau.to/oiU/1AXAA00051
• Needle nose pliers 1aau.to/oiU/1AXAA00052
• Side Cutters
• T30 Socket
• Ratchet 1aau.to/o6j/1AXAA00016
• Socket Extensions 1aau.to/oSB/1AXAA00015
• 5mm Hex Socket
• 5mm Hex Wrench
For More Info visit us at 1aau.to/h/bPw/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravní prostředky
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Y’all are lifesavers nobody really posts videos of them working on this car specifically or I’m just unlucky at finding what I need but anyway thank you !
This is by far the best instructional on replacing this sensor, have looked through many and this is on the spot what I needed! Thanks! I have a code 065 for this sensor and the car runs really rough when cold, and also low on power when accelerating hard when warm. Previous owner had the opposite problem and replaced the valve with a cheap $25 "Ridex" one. I have read that you really need to get the original one from BMW. I'm installing a $40 Hella-brand, should be OEM original, hoping it will at least get this code cleared. After that on to the rest (All 4 O2 sensors throwing "value too low"...
+Magnus von Rosen Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
would a bad cam position sensor cause any other codes like and control pressure solenoid (trans. code)?
What would one recommend if the VANOS Solenoid doesn't wanna play ball and break loose ? Because that's the issue i'm having. I don't wanna risk rounding the solenoid entirely but constantly trying to break it with an Adj. Wrench. I even took the liberty to order the specialty socket to remove the solenoid but now face the issue of space to even get the socket on... Any advice would help because, the only two choices i see is to remove the VANOS unit entirely because the solenoid is attached to it - or remove the Intake Mani. and use the specialty tool . 🤔🤔
This was very helpful. Thank you so much!
+Jova Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Is removing the negative side of the battery cable necessary? I dont see that function on any other of the CZcams videos.
+Stan Cahn Thanks for watching! Yes you will want to disconnect the negative battery cable when performing this repair.
I have p1343, p1345, p1351 codes and they all say Misfire with furl cut off, cylinder 1,2 and 5. I replaced the fuel injectors, coils and sparks and maf sensor and exhaust cam shaft sensor... it's so bad I keep stalling. It's a 2001 bmw 330ci 5spd manual... I'm getting tired of this can u help me... and also my vanos valve is stripped bad I can't even get it off what do I do.. help... I can't even drive it anymore it's that bad... I also have ignition coil wiring coming thru... tomorrow.
+Lil Honda97 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Will it make car stall and misfre?
+Xduwhopfilmz Filmz We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
yes mine stall alot when it get to operating temps and also doesn't have any power at all at full throttle the car accelerate really slow,rev really slow and missfire. i have P0344 / P0340 hard error. i ordered new cam shaft intake sensor ill replace it and will tell you what happens after all *(i thought it's the ICV i cleaned it but the car keeps stalling i used inpa/ista/BMW scanner and still have the Camshaft intake sensor.
@@3ManFunny So ? What happen ? Did you bought an OE or Genuine BMW sensor ?
Obd2 shows a p1347 feul cutOff code. Other possibles for that series of code are faulty injectors, coils, harness. Additionally have a look at the tensioner pulley if its bouncing its bad.
@@jeremypowers4647 e46 starts up and immediately dies. Fuel pump primes fuses okay. Could it be intake cam sensor that is causing this?