Honda NC750X Annual Service Oil Change

Sdílet
Vložit
  • čas přidán 8. 10. 2021
  • Oil Filter Wrench: www.amazon.co.uk/CNWOOAIVE-Ad...
    Oil: www.halfords.com/motoring/mot...
    Oil Filter: www.halfords.com/motorcycling...
    Step by Step:
    First thing you want to do is put your bike on the main stand and make sure its on a flat surface, if you don't have a main stand you will need an assistant to check the oil level at the end.
    The oil im using is castrol power 1 ten thirty, I use this because of the climate in the UK, if you live in a hotter country I recommend using ten forty, the API quality for this oil is SL which exceeds the SG recommendation by Honda, the MA classification and code is JASO T 903 which is also recommended by Honda.
    Here's the items that I used, oil filter wrench, 17mm socket, 12mm socket, 3 8 wrench, 5mm allen socket, magnetic drain bolt, and the correct oil filter, all link to these are items are listed in the description.
    Now run your engine for 5 minutes an get the oil nice and warm, this will make the oil thinner and easier to drain.
    Remove the lower engine cover with a 5mm allen key as shown
    After 5 minutes switch the engine off,
    use a suitable drain bowl and place underneath the engine
    unscrew the oil filler cap as shown
    here is the sump drain bolt use a 12mm socket and loosen the bolt counter-clock wise you can tap the wrench with your hand to shock the bolt loose. Move the drain bowl slightly over because the oil will shout out fast sideways, be very careful not touch the hot exhaust, wearing gloves is recommended
    while that is draining go to the other side and using the oil filter wrench careful remove the filter, it will be very tight, this type of filter wrench grips the filter as you pull down on the wretch with its built in gear mechanism as shown.
    Now finish unscrewing the oil filter
    make sure the rubber ring comes off with the filter and not stuck to the engine
    wipe the surface clean making sure there is no dirt on the ring or thread
    make sure the filter boss inst sticking out no more than 17mm, if it is you will need to remove the boss and apply thread lock and screw it back in, having said that its quite uncommon for this boss to move.
    Grab the new oil filter, this filter has grease already smeared on the seal, if your filter doesn't then apply a thing layer of oil on the rubber seal before installing
    carefully screw the filter in with your hand
    do not use any tools to install the filter, it should only be hand tight, if you have a weaker hand use a piece of emery cloth to grip the filter as shown
    grab the new sump bolt and install the washer, you can see this bolt has a magnet on the tip to catch possible filings if any end up in the sump, its not inessential but I like having one
    if you are suing the old sump bolt and washer you can flip the washer round and it will be fine.
    Now install the sump bolt with your fingers, once you cant screw it any more put the socket on the bolt and tighten to 30nm.
    Now wipe off all the excess oil from around the sump and oil filter, use bake cleaner if you have some.
    Grab a suitable funnel and pour 3 litres of oil into the engine, use the container for a guide of how much you have put in. this is a 4 litre can and I have 1 left so ive poured 3 litres in.
    remove the funnel, clean the dip stick, put the cap in the filler hole but don't screw it in, just butt it up to the engine and remove, if you dont have a side stand get and assistant to hold the bike up right on flat ground
    check that the oil isnt below the minimum or above the maximum lines
    install the cap and start the engine
    leave running for one minute and check underneath for any leaks
    now switch off and leave for 2 minutes
    re check the dip stick and add the required amount so its touching the top line, I was required to add another 400ml of oil and that was enough. So I have poured a total of 3,4 litres of oil in the manual nc750x, dct models may hold a little more so please check first
    once you are happy install the oil cap fully and wipe clean
    now reinstall the engine cover as shown
    find an old oil can and pour the old oil into it, make sure you take this to your local waste centre along with the oil filter.
  • Auta a dopravní prostředky

Komentáře • 131

  • @thebuyerboy
    @thebuyerboy Před 2 lety +14

    One of the clearest videos I have ever seen on how to do this operation. Well done!

  • @SeakalalaMojapelo-yg8jm
    @SeakalalaMojapelo-yg8jm Před 10 měsíci +2

    Thank you very much for the demonstration. Honestly, Honda should not require strictly authorized dealers to do this task. Any average person like me can do this, safely so.😊

  • @jarekhaus2808
    @jarekhaus2808 Před rokem +1

    Wszystko bardzo profesjonalnie!👍, dziękuje i przyda mi sie do mojej nowej Hondy.Pozdrawiam serdecznie

  • @vincentlicence5498
    @vincentlicence5498 Před 2 lety +7

    Very calm and stress free demonstration. Watching your videos have given me confidence in my decision to buy one of these motorbikes.

    • @nicksepisode
      @nicksepisode  Před 2 lety +1

      Thank you, good luck with the new motorcycle

  • @DSPeti
    @DSPeti Před 2 lety +1

    Perfect video. Now i"am 100% sure how to change oil on my 750xd 2017. Thank you so much.

  • @djpunisha29
    @djpunisha29 Před 2 lety +1

    love your maintenance videos, thank you for sharing, safe ride, and clear roads!

  • @EmpZombie
    @EmpZombie Před 2 lety

    Excellent video on how to do this. It gives me the confidence to give it a go myself. Thank you.

  • @simoncrehan7779
    @simoncrehan7779 Před 9 měsíci

    Awesome video. Oil change so clearly explained. I know exactly what to do now…Thanks!

  • @wokeupandsmellthecoffee214

    Brilliant tutorial thanks for taking
    The time
    To do it and put it
    On CZcams for us .

  • @jorgensen8
    @jorgensen8 Před 2 lety

    Wonderful clear oil change video. Thanks!

  • @kanochromia
    @kanochromia Před rokem

    Thank you for this tutorial! I managed to change the EO on my own. :)

  • @michaelevans1658
    @michaelevans1658 Před 2 lety

    Clear and concise ,what more do we want ?

  • @keith4usa1
    @keith4usa1 Před 2 lety

    Cheers Nick Absolutely brilliant, so its a Dip stick Oil checker...Much better than Dry sump models

  • @martinder1963
    @martinder1963 Před 2 měsíci

    The video’s are useful to me. Thx and greetings from The Netherlands.

  • @johnofypres
    @johnofypres Před měsícem

    Nice clear, easy to follow video. Thank you.

  • @jeffgravitt3732
    @jeffgravitt3732 Před 2 lety

    Really good job! Thanks, Nick.

  • @miguelangelmartilgarcia7801
    @miguelangelmartilgarcia7801 Před 4 měsíci

    Just a perfect and didactic video. Thanks

  • @Rob-The-Gob
    @Rob-The-Gob Před rokem

    Nice vid! Thanks! saved me a small fortune :)

  • @geecee4746
    @geecee4746 Před 2 lety

    I would love to be able to work at my bike, but i wouldn't trust myself 😂😂good video nick👌👌👍👍

    • @nicksepisode
      @nicksepisode  Před 2 lety +1

      You can do it! Thanks for your comment 👍

  • @markmiller5577
    @markmiller5577 Před rokem

    Superb video ,clear and well explained.

  • @northeastcrow586
    @northeastcrow586 Před 2 lety

    Great videos, thank you for doing them

  • @Markdmarque
    @Markdmarque Před 10 měsíci

    Excellent, very clear video
    Thanks

    • @nicksepisode
      @nicksepisode  Před 10 měsíci

      Thanks, glad you found it helpful 😀

  • @michelod.i.y.5202
    @michelod.i.y.5202 Před 2 lety

    Nice clear instructions

  • @gazbev1423
    @gazbev1423 Před 4 měsíci

    Very good vid, thank you

  • @stevethorndale231
    @stevethorndale231 Před 2 lety +1

    Just subscribed, nice clear video and good info. I prefer to use a torque wrench where values are given. I have a Honda oil filter removal tool which is used for removing and replacing the filter without causing any damage. It also allows a torque wrench to be used to tighten the filter up to it 26 lb ft figure. Ex mechanic so I have a lot of the tools to hand.

  • @pg41226
    @pg41226 Před rokem

    Just a little suggestion when using the sump plug washer again, hit the washer with some sandpaper. This way you remove the old “sealing” marks on the washer and you get a clean smooth washer again. Don’t forget to clean the washer afterwards.

  • @davestewart2215
    @davestewart2215 Před 2 lety

    This is what youtube was invented for. Just done mine and many thanks indeed .
    Can I just point out,on my 2018 NC 750 dct, the right hand fixing screw is longer than the left one. Baffled me for a few mins if I am honest.

    • @nicksepisode
      @nicksepisode  Před 2 lety +1

      Thanks for watching and I'm glad my video was helpful, well spotted on the screw, thanks for letting others know.

  • @RadiustechnologyCoUk
    @RadiustechnologyCoUk Před rokem

    Thanks Nick!

  • @neilwiddison6529
    @neilwiddison6529 Před 2 lety

    Hi nick I have put motul in my bikes . Might try the castrol.

    • @nicksepisode
      @nicksepisode  Před 2 lety +1

      HI Neil, I've never tried motul I've heard nothing but good things about it, but I choose Castrol as its recommended by Honda

  • @_skud
    @_skud Před 7 měsíci

    thank you!

  • @__Razer
    @__Razer Před rokem

    This is the best, most clear, and in-depth video I've seen for changing oil on this bike. I have a couple questions though:
    I know you said you can re-use the crush washer if you flip it around, but what do I buy to replace it if I think a previous owner might've flipped it or reused it in the past and I want to be safe with a new one? Is it a part I can find in my local automotive parts shops, or do I need to order through Honda?
    Also, I thought the draining procedure is best done on the side stand, rather than the center stand? Is that true? The center stand is used when checking the oil level.

    • @nicksepisode
      @nicksepisode  Před rokem

      You can use a car drain washer too. Centre stand is best for drainage. Thanks for watching

  • @PPcko
    @PPcko Před rokem

    Thank you for the video. It is really easy to understand.
    I have just one thing I need help with. What's the sice of sump bolt please? Is it like M12X1.25? Thank you.

    • @nicksepisode
      @nicksepisode  Před rokem

      so sorry i dont know as ive now sold the bike

  • @ianskeldon6032
    @ianskeldon6032 Před 2 lety

    Another nice video Nick. Do you know where I can get a service manual for my nc750 as I want to maintain it myself.

    • @nicksepisode
      @nicksepisode  Před 2 lety

      Join the worldwide Facebook owners group and there is one on there you can download as a PDF

  • @brockett
    @brockett Před 2 lety

    Good clear video well done. I am all for DIY and saving some cash but does your home servicing and use of non Honda filter invalidate your bike's warranty? And ... where did you get the magnetic drain bolt?

    • @nicksepisode
      @nicksepisode  Před 2 lety +1

      Link for the bolt is in the description, I only have a few months left of warranty, besides its a Honda whats warranty 🤣 thanks for watching

  • @1over137
    @1over137 Před 2 lety

    First try and undo the oil filter by hand. Then increase your tools until it comes loose. You don't need the fancy wrench if you can't afford one. The cheaper ones, like chain straps, don't work. When doing it up, a bare hand grip only. If you get stuck a local bike shop may lend you a pro-tool for an afternoon FoC if you are polite. As long as you have a second mode of transport, have at it.

    • @1over137
      @1over137 Před 2 lety

      In an emergency you can "hack it off" with a screwdriver rammed through it and used for leverage. When that fails you have pretty much opened it like a can anyway, so strip it back and grab the actual core with vice grips to crack it open. If someone else serviced your bike last time... don't go back.
      Oh... and expect a LOT of mess to clean up.

    • @nicksepisode
      @nicksepisode  Před 2 lety

      The tool linked is 6.99, does the same job as my snap on one, I'm yet to find an nc750x filter hand loose after a year of use, but you never know 😅

  • @happygilmorides7353
    @happygilmorides7353 Před 2 lety +1

    Nice vid pal. May I ask, does the oil level have to be done on the stand or off? My biffer has to be on the ground held up. Didnt know if it made a difference for the NC. I ask as I'm looking at buying a 21k 2016 model soon. Ride safe

    • @nicksepisode
      @nicksepisode  Před 2 lety

      On the centre stand so the bike is upright

  • @nikos-giorgos
    @nikos-giorgos Před 10 měsíci

    1:30, I believe the correct oil filter is the one bought directly from Honda.
    This will fit but it's not the correct one.

    • @nicksepisode
      @nicksepisode  Před 10 měsíci +1

      Honda don't make oil filters, they buy them from oil filter companies and stamp Honda on them and charge you more money. Its only wise in todays economic crisis to think smart and save money

  • @ralphbeardmore9738
    @ralphbeardmore9738 Před rokem

    I am glad I saw if I could loosen the oil filter first as my chain wrench would not budge it so ordered a better one like yours. By the way what was the 17mm socket for?

    • @nicksepisode
      @nicksepisode  Před rokem +1

      The New sump bolt that I replaced, it was upgraded with a magnet

  • @rickyrichreacts9667
    @rickyrichreacts9667 Před 2 lety +1

    *HEY GUYS, I NEED SOME HELP!*
    I changed my oil and oil filter yesterday on my 2011 kawasaki ninja 250 and when I went to tight the filter cover and oil filter mounting bolt, I broke the filter cover.. It's in pieces and I've been searching all over to get a replacement but where's a good place to order one? Or could I use another oil filter cover at maybe a local hardware or bike shop??

  • @aceshimizu1941
    @aceshimizu1941 Před 7 měsíci

    Would like to know if there is a chance to use hf303 hiflo oil filter instead of hf204 for the bike

    • @nicksepisode
      @nicksepisode  Před 7 měsíci

      Always use what's recommended. They may look the same but internals could differ

  • @dimosthenismagos7982
    @dimosthenismagos7982 Před 3 měsíci

    Hi, nice job ! Do you shake the 4 litter bottle prior to use or not ? Thank you.

  • @volt8684
    @volt8684 Před 2 lety

    Exhaust looks v rusty from underside shots? Does your acf treatment not prevent this. My bike 16yrs old chrome exhausts and almost as new

    • @nicksepisode
      @nicksepisode  Před 2 lety +1

      the stock header is prone to rust, but its only surface rust, i use it all year round, with cleaning weekly this can be prevented, but im ok with a rusty header as most of it is hidden

  • @dumitrunistor5516
    @dumitrunistor5516 Před 14 dny

    Hi !
    What is the blue bar transverse on the handle bar ?
    Did you mount yourself ?
    Can be bought from internet ?
    Thanks !

    • @nicksepisode
      @nicksepisode  Před 14 dny

      you can buy it here accessories.hitchcocksmotorcycles.com/accessory-shop/handlebars/42987

  • @birchwoodbiker
    @birchwoodbiker Před 2 měsíci

    Nick can I just ask how did you get the coms recorded in both helmets when you rode together, I have Cardo and DJI action 3 and just doesn't play, You see us youtuber's keep the idea for future content, your camera is always going to call you now 🤣whould be great to know your setup

    • @nicksepisode
      @nicksepisode  Před 2 měsíci +1

      I purchased the dji usb c microphone and shoved them in both our helemts. We only use intercom to speak to each other

    • @birchwoodbiker
      @birchwoodbiker Před 2 měsíci

      @@nicksepisode OK cheers, I have the wireless dji it's just pulling all the data off and sinking, I may have found a way with Y lead, hope you through the odd bit content, it pays for your petrol, meant to say You should of bought the NC DCT🤣🤣👍

  • @Antimortem
    @Antimortem Před 2 lety

    ❤️👍

  • @Richard-dh8ny
    @Richard-dh8ny Před rokem

    Nick, thanks for this helpful video. Question if you have time to reply... Is that an aftermarket oil drain plug? My 2013 doesn't have magnetic plug, so I'm curious if I can order one through my local dealer.

    • @nicksepisode
      @nicksepisode  Před rokem

      Hi Richard, that's an aftermarket drain plug, link to buy it is in the description below. Thanks for watching

    • @Richard-dh8ny
      @Richard-dh8ny Před rokem

      @@nicksepisode Thanks Nick, but I don't see any description or link to the product.

    • @nicksepisode
      @nicksepisode  Před rokem

      @@Richard-dh8ny www.ebay.co.uk/itm/363954015010?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=OUd2zYVDSHq&sssrc=2349624&ssuid=_QCxPrBSSWS&var=&widget_ver=artemis&media=COPY

  • @kevinjackson5071
    @kevinjackson5071 Před 2 lety

    Hi nick, am getting all items together to do oil and filter change. Where do I buy the sump plug and washer you have used ? Many thanks

    • @nicksepisode
      @nicksepisode  Před 2 lety

      Link is in the description, it's from ebay, thanks for watching

    • @kevinjackson5071
      @kevinjackson5071 Před 2 lety

      Hi. Sorry I don't see it. Theres a link for oil, oil filter & filter tool but not sump plug.

    • @nicksepisode
      @nicksepisode  Před 2 lety

      www.ebay.co.uk/itm/Warrior-Sump-Plug-Washer-Suitable-for-Honda-NC750X-2016-/363300234175?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=710-127635-2958-0

  • @jdw1407
    @jdw1407 Před rokem

    what blue bar is across your handle bars?

  • @justforco
    @justforco Před 23 dny

    Спасибо за информацию. Она пригодилась владельцу NC 700X в россии😅

  • @jonasvanheeke4280
    @jonasvanheeke4280 Před 2 lety

    Where did you get the crossbar?

    • @nicksepisode
      @nicksepisode  Před 2 lety

      Ebay it's a renthal one, link is in the description on my ownership review video

  • @leekimran6369
    @leekimran6369 Před rokem

    What’s the 17mm socket used for?

  • @japadaj
    @japadaj Před 2 lety

    You should pour oil into the filter before screwing it on.

  • @sparkyspark1582
    @sparkyspark1582 Před 2 lety

    Love your video .any idea how much oil in the dct version please is it 4.1 l ? Or 3.4 l ?

    • @nicksepisode
      @nicksepisode  Před 2 lety

      DCT type:
      3.2 liters (3.4 US qt, 2.8 Imp qt) at draining
      3.4 liters (3.6 US qt, 3.0 Imp qt) at oil filter change
      4.1 liters (4.3 US qt, 3.6 Imp qt) at disassembly

    • @tekoslabse
      @tekoslabse Před rokem

      @@nicksepisode Why did you use only 3L of oil for oil + filter change?

    • @tekoslabse
      @tekoslabse Před rokem

      Just read the description, you poured 3,4l total.

    • @nicksepisode
      @nicksepisode  Před rokem

      @@tekoslabse best thing to do is top up gradually and check yourself

    • @dazouk
      @dazouk Před 10 měsíci

      @@tekoslabse he top up afterwards

  • @dazouk
    @dazouk Před 10 měsíci

    What’s the washer size ?

    • @nicksepisode
      @nicksepisode  Před 10 měsíci +1

      Sorry bud I have no idea. Link to sump bolt is in the description

  • @Rgd250
    @Rgd250 Před 2 lety

    do yo have the service manual of this model ? not the DCT 2020 NC750X ?

    • @nicksepisode
      @nicksepisode  Před 2 lety

      I do

    • @Rgd250
      @Rgd250 Před 2 lety

      @@nicksepisode can you please give me the URL ? BTW great video and I really enjoyed watching it :)

    • @nicksepisode
      @nicksepisode  Před 2 lety

      Thanks Roy, join the nc750x Facebook page it's on there 👍

    • @Rgd250
      @Rgd250 Před 2 lety

      @@nicksepisode I'm allready there didn't saw it

  • @LandRoverDS2020
    @LandRoverDS2020 Před 2 lety

    I haven't watched the video yet but I was wondering for your wife to move up to a bigger bike wouldn't this be a great option and in an auto ?
    Can she touch her feet on the ground or toes on your bike ?
    Andrew

    • @nicksepisode
      @nicksepisode  Před 2 lety

      Hi Andrew, yes she can touch the floor on this, however she loves the new 2021 cb500x

    • @LandRoverDS2020
      @LandRoverDS2020 Před 2 lety

      @@nicksepisode ah yes another good choice

  • @pandalung2616
    @pandalung2616 Před 2 lety

    可以分享DCT系統的油更換嗎?

  • @thespian1961
    @thespian1961 Před rokem

    Thuh oil? Are you American?

  • @Brian0059
    @Brian0059 Před 2 lety

    Made me laugh I got busted today by wife for using her pink microcloth / flannel , wiping down bike 😁

  • @hussienabukhalil2012
    @hussienabukhalil2012 Před rokem

    Nice vedio bad music

  • @user-tl6ri9tn6w
    @user-tl6ri9tn6w Před 2 měsíci