Quick fix for the wipers to get them aligned properly once taken off is to remove them both, turn the car ignition on and press down on the wiper control and that will reset them back into the stock position. Big pain trying to get them lined up properly until I found out about this solution. Pretty easy install otherwise!
I literally just did my coilovers rn and my problem now is the driver side is aligned but the passenger wont come up... its like it trys to because i can see the wiper move a little but its almost like its stuck
I’m really enjoying you’re videos. As far as I can tell you are the only shop putting out professional mod videos for the ST. Thank you for putting theses videos out there. Can you recommend a reputable performance shop in California to work on my ST?
Thank you for making this video as I couldn't work out how the hell to get the shock back in the hub with out heating it up and I really didn't want to heat it up so thank you
To bad you have to use the stock top mounts for the kit. The BC racing coils have their own camber adjustable top mounts. The kit looks pretty good value for money otherwise.
@@joer5085 It was an 05 XT. I only ran them for a few thousand miles before selling the car but they were great. Easy to adjust and was able to use the stock top hats for my needs.
I have the exact same suspension for my 2016 VW GTI. Had it professionally installed with a conservative drop. I don't track the car and baby it. This kit has been absolutely nothing but problems for me. Kit needed to be rebuilt after a few months under warranty and still problems. Never again.
Yeah, great video. I'm guessing, given your experience here, your suspension improvement recommendation would be coilovers first and then maybe the rear sway bar isn't really necessary, right? And this car sounds great! In comparison to how I got my 2013 ST from the showroom, that's a function of what? Thanks!
In order to adjust the rear height, do you have to take off the wheel or any other part? Can you adjust the rear height while the car is on ground or you ya e to lift it?
What rims are those again and are you using spacers? If not was is the offset? Pretty great looking suspension kit for the price when compared to a separate spring and strut combo. Nice video and thanks!
I heard a blip about the sway bar upgrade not being necessary with this kit. I was looking at the ST Suspensions rear sway bar to along with this kit - would you say that's just not needed? Thank you.
Bill, I just installed this kit today and I cannot seem to adjust my ride height in the rear. I turn my Allen key a quarter turn out, and when I release pressure it will turn a quarter turn back to where I started. Lots of tension. Obviously I’ve done something wrong but I followed your video step by step so I can’t think of anything that I’ve missed. . Any thoughts? Thanks!
Bill Tumas, I just had a similar kit installed (Bilstein B-14 PSS) with new bump stops and adjustable rear toe links. I am hearing clunking noise when I roll over small bumps and when I turn the wheel back and forth. Though the suspension seems to make my car handle better the suspension feels almost loose when I roll over any bump in the road. Would you have any opinion on what might be causing these issues?
+bon vivant The first time you remove them, right, no shimmying will help you. Just push on the curved part and the assembly will pop off a bit, then shimmy. After that, they are really easy to remove. Don't forget to mark the position of the wipers (I used a sharpie for it) so that when you put them back on, they're at the same position as they were.
Anyone who hasn't installed them yet.... go buy a wiper arm puller. I had the same issue doing this install on a Fiesta ST. It should be listed on the tools. And you can you masking tape to mark where the blades sit on the window.
Hey, I like the video... I got eibach prokit on my scirocco (2012) but Im bored of it. So i want to buy coilovers, but in my country the taxes are so high, I wanted to buy JOM blueline coilover. is this a bad idea ? could you please help? Thank you. and btw, im not a guy driving sooo fast and unaware, Im %90 calm. Nevertheless should I buy kw?
Hey bill. I have a 2017 Ford C-Max and was looking at the bc coilovers but don’t think they make anything for My car. Does the cmax share suspension components with the focus or anything else? Tks
Please tell me how you got the strut end link off? There is no place to put a 17mm wrench, it's literally round and using an Allen and an open ended doesn't work do to there being two metal walls up on either side
@@kooletron174c3 you'll get it eventually. I think I ended up using that method. Hardest fucking job I ever did on my car. I would definitely bring it to a shop next time. Fuck that. Good luck man! Save that money on this one though. The back ones are cake!
MedicBobs yup and then I split the knuckle too much and ended up stripping it , had to go back with a cut and die set and re thread it ... pain in the ass
out of all the times i have done suspension on cars, the one thing i can never get perfect is aligning the front suspension top hats the first time around. i always put it all together.. install the bottom to find out the top mount isnt aligned right. is there an easier way to get it right the first time? i just got a 2014 ST and want to do the suspension very soon.
Quick fix for the wipers to get them aligned properly once taken off is to remove them both, turn the car ignition on and press down on the wiper control and that will reset them back into the stock position. Big pain trying to get them lined up properly until I found out about this solution. Pretty easy install otherwise!
I literally just did my coilovers rn and my problem now is the driver side is aligned but the passenger wont come up... its like it trys to because i can see the wiper move a little but its almost like its stuck
I just installed these coilovers and did not disconnect the wipers at all.
@@IhateSIGNINGup4this just coming back to this to see if you could tell me how you did it without taking the wipers off?
I’m really enjoying you’re videos. As far as I can tell you are the only shop putting out professional mod videos for the ST. Thank you for putting theses videos out there.
Can you recommend a reputable performance shop in California to work on my ST?
Thank you for making this video as I couldn't work out how the hell to get the shock back in the hub with out heating it up and I really didn't want to heat it up so thank you
To bad you have to use the stock top mounts for the kit. The BC racing coils have their own camber adjustable top mounts.
The kit looks pretty good value for money otherwise.
Great video. I'm putting these on my Subaru Forester this weekend and aside from the differences on the rear, is exactly what I needed to see. Thanks!
What year was your forester and how did you like them?
@@joer5085 It was an 05 XT. I only ran them for a few thousand miles before selling the car but they were great. Easy to adjust and was able to use the stock top hats for my needs.
I have the exact same suspension for my 2016 VW GTI. Had it professionally installed with a conservative drop. I don't track the car and baby it. This kit has been absolutely nothing but problems for me. Kit needed to be rebuilt after a few months under warranty and still problems. Never again.
Curious what's the problem you have? I have the same car and i just bought the kit
Ride height is fine on this car, not too high from the factory
ST STX or BIlstein B14? Which's better?? I' m not sure which to buy.
Great video, thanks. I have ST suspension fitted to my VW Caddy, I rate it very highly.
I didnt get the X line, but I have the STs in my kitchen ready to go on my MK6 GTI *BIG GRIN* I CANNOT WAIT!!
Yeah, great video. I'm guessing, given your experience here, your suspension improvement recommendation would be coilovers first and then maybe the rear sway bar isn't really necessary, right? And this car sounds great! In comparison to how I got my 2013 ST from the showroom, that's a function of what? Thanks!
brake caliper covers.... really??
Newbie question: Could one follow the same installation instructions for the 13' Focus SE?
I would love to do this to my car. But i need the ability to drive in winters in Michigan. Ride height issues
This helped me a ton on my Mazda 3. They have basically the same suspension setup.
In order to adjust the rear height, do you have to take off the wheel or any other part? Can you adjust the rear height while the car is on ground or you ya e to lift it?
Dis you guys have to replace the rear camber arms prior to this install?
love these videos and they also make we want that red!
What rims are those again and are you using spacers? If not was is the offset? Pretty great looking suspension kit for the price when compared to a separate spring and strut combo. Nice video and thanks!
I heard a blip about the sway bar upgrade not being necessary with this kit. I was looking at the ST Suspensions rear sway bar to along with this kit - would you say that's just not needed? Thank you.
+TheChicken2001 I have not tried that sway bar so I cannot say. This car feels very tight and the handling is impressive with the stock bars.
Maybe i missed it or its not really needed but the rear LCA, doesn't it need to have the suspension loaded on the ground to tighten?
Bill, I just installed this kit today and I cannot seem to adjust my ride height in the rear. I turn my Allen key a quarter turn out, and when I release pressure it will turn a quarter turn back to where I started. Lots of tension. Obviously I’ve done something wrong but I followed your video step by step so I can’t think of anything that I’ve missed. . Any thoughts? Thanks!
many people told me that the st-x suspension is more comfortable than stock, is that true?
I can fit my shoe in the wheel gap... WAY TOO MUCH GAP
***** shoe test FAILED
spit fire lol I know it’s a late reply your are 100% correct I have the gap and I just fitted a set of eibachs ..pro kit
Seems a waste of coilovers
Laugh Now Cry Later rebel devil custom drop springs or bust!
@@MrGreen_ is the pro kit a 1" drop ? What does it look like
Bill Tumas, I just had a similar kit installed (Bilstein B-14 PSS) with new bump stops and adjustable rear toe links. I am hearing clunking noise when I roll over small bumps and when I turn the wheel back and forth. Though the suspension seems to make my car handle better the suspension feels almost loose when I roll over any bump in the road. Would you have any opinion on what might be causing these issues?
Shimmy the wiper my ass! Lol
+bon vivant The first time you remove them, right, no shimmying will help you. Just push on the curved part and the assembly will pop off a bit, then shimmy. After that, they are really easy to remove. Don't forget to mark the position of the wipers (I used a sharpie for it) so that when you put them back on, they're at the same position as they were.
Emmanuel Thioux I wish I would have known about marking them prior to getting them off lol.
Anyone who hasn't installed them yet.... go buy a wiper arm puller. I had the same issue doing this install on a Fiesta ST. It should be listed on the tools.
And you can you masking tape to mark where the blades sit on the window.
Ive been running mine for a month now and im getting knocking noises when turning my wheel and going over bumps at low speeds
Hi Dalton, did you find the problem on your suspension? I have the same issue.
It might not have the preload set correctly thats why you might be hearing that noise, you are probably riding on shocks only, see of that helps.
great suspension!
I noticed the stock rear bum stop, is that where the eibach sportline bump stop should be installed?
We installed it there and it works without issue but Eibach recommends installing it on the rear shock itself.
Bravissimo! Complimenti!
Hey, I like the video... I got eibach prokit on my scirocco (2012) but
Im bored of it. So i want to buy coilovers, but in my country the taxes
are so high, I wanted to buy JOM blueline coilover. is this a bad idea ? could you please help? Thank you. and btw, im not a guy driving
sooo fast and unaware, Im %90 calm. Nevertheless should I buy kw?
Really good video...
Bill did you put on wheel spacers after lowering ?
Good job men you explain good 👌👌👍👍👍
@skates4vans No we did not
Will this be basially the same concept on a 2014 ford focus se
Yes the geometry is the same
i have focus sedan .my wife doesn't agree i low it.
Why is the whole axle flopping around at 8:05? That doesn't look right.
+Jordan Bierbaum because there is no strut tower to keep it straight and level, so it is very moveable, but it is meant to be like that
Also my rear shocks started leaking a month after install
How is this working with 19inch wheels 19x8,5 ET 35 ?
Hey bill. I have a 2017 Ford C-Max and was looking at the bc coilovers but don’t think they make anything for My car. Does the cmax share suspension components with the focus or anything else? Tks
Not that I am aware of, I have never seen any performance parts for the CMax
The parts list though 😂😂
Great video as always. Do you leave the stock rear bump stop? And I'm guessing you have to take the wheels off the car to adjust the front height?
You can leave it or take it off, doesn't matter either way. The more functional stop was in the factory shock. Yes you need to remove the wheels.
Bill Tumas cool thanks man
Please tell me how you got the strut end link off? There is no place to put a 17mm wrench, it's literally round and using an Allen and an open ended doesn't work do to there being two metal walls up on either side
Dude seriously I’m stuck as I’m typing this .....
@@kooletron174c3 you'll get it eventually. I think I ended up using that method. Hardest fucking job I ever did on my car. I would definitely bring it to a shop next time. Fuck that. Good luck man! Save that money on this one though. The back ones are cake!
Hahahaha same here ... definitely took a lot of bullshit . Ended up just vice gripping the back of it and using the 15mm
@@kooletron174c3 hahaha same! Did u finish it?
MedicBobs yup and then I split the knuckle too much and ended up stripping it , had to go back with a cut and die set and re thread it ... pain in the ass
did you have lsd diff ???
There isn't any issues with taking speed bumps or dips in the road with this ride hight is there?
So far not at all. We did not go extreme with the drop though.
What's the name of the wheels??
out of all the times i have done suspension on cars, the one thing i can never get perfect is aligning the front suspension top hats the first time around. i always put it all together.. install the bottom to find out the top mount isnt aligned right. is there an easier way to get it right the first time? i just got a 2014 ST and want to do the suspension very soon.
I'm not sure what you're talking about, but I did mine today and it was a piece of cake. Time consuming, but easy.
Use a strong piece of scrap metal so when you thread the bolt through you don't thread the bolt into the metal......:(
No how to on the rear spring adjustments....
Does lowering your car actually have any benefits?
Lowering with good quality components makes a noticeable difference. Lower center of gravity improves handling. Less roll in corners, less brake dive.
I tried this now my new shocks are squeaky
Compare the oem suspension, ride is smoother with this suspension or the additional with rebound adjustable?
Its a little firmer than stock but the ride was very livable.
@@cjponyparts can it be adjusted a bit higher than In the video? I'm running spacers and my car needs struts anyway so I'm considering these
Can these also be adjusted to be just a little bit higher than in the video?
How’s you get the abs bracket off so easy?
Right?
Can this work if you have wheel spacers?
unlimited haro78 yes
What rims and tires are those?
www.cjponyparts.com/niche-targa-wheel-18-x8-matte-black-with-tinted-face-accents-focus-st-2013-2018/p/W635-V/
Like a high fructose corn syrup fed Turbo Yoda
Odell it is the same basic concept
wats the rock song in the background?
+sarpiresthedatsuns I have no idea, we get everything we use from royalty free music sites.
Sarude-Danstrom
Needs a brake upgrade while you've got the wheels off