Can I get it to run? (Working on Yamaha 25 outboard)
Vložit
- čas přidán 13. 06. 2023
- Hey guys in todays video I got a sweet 25 rebuild for you. These are some of the most reliable motors and personally one of my favorites. Hope the vid helps you out and hope you enjoy it
Parts used:
Music credits:
Get Below Freezing by Daniel Gautreau and over 1M + mainstream tracks here go.lickd.co/Music
License ID: NrderaJ1A0v
Get Diamonds by George Georgia and over 1M + mainstream tracks here go.lickd.co/Music
License ID: pdWpGPr2jMO
Get Blunted by George Georgia and over 1M + mainstream tracks here go.lickd.co/Music
License ID: wWnV4Z1lmP5 - Auta a dopravní prostředky
Thanks
Great job as always you are very good teacher btw did you recheck the compression? Chris from OHIO gooooooo Buckeyes
Great in depth look at rebuilding the carbs. Thank you!! Makes me wanna check out marketplace for some “dead” outboards.
Nice work, rebuilding the carbs on one of these seems daunting. I’m just venturing into boats and doing my research this is good stuff keep up the great work👍🏻
Okay another great 1
Great job man.. sometimes you gotta have faith and it pays off.. i got a mercury im doing on my channel now and a yamaha w low compression next.. keep up the vids
Next time try removing and replacing carbs attached to the air box backing plate. You will have to loosen the pull rope assembly but easy all in one piece my friend. Great job
Hey thanks for this comment. I figured there was something like that that you could do but this was my first w these models so just went out on a whim lol. But now I know. Appreciate the feedback!
Good video
Hey you're tutorial are along the very Best I have the same engine but a 20 hp. Up north outboard Last 50 years if maintained well those yamaha are gem
Thank you I really appreciate that I hope it helped out
If you take the recoil starter off the carbs are way easier to get off you can just take it all off in one piece
Yea I think someone else mentioned something similar about doing that. Ima be doing that from now on as this was the first Yamaha 25 I’ve done a video for so greatly appreciate the advice and feedback!!!
hey man love the videos where can I contact you have a couple question on my engine
I can answer qs on here for ya
I have a 90hp mercury 4 stroke sometime when I go from forward to neutral my engine shuts off or from reverse to neutral but not always thanks@@outboardfinatic
This is completely off topic, please forgive me, I have a 9.9 merc 4 stroke non bigfoot and I was wondering if the tell tale port can be removed and cleaned( area under thermostat)
I mean it can but what’s the issue? If something’s clogged try dropping the lower unit and putting air pressure in the water pick up tube and feel of you can feel air out the tell tale
@@outboardfinatic Thank you once again for the response and help
Salve irmão aqui Brasil 🇧🇷🇧🇷🇧🇷🇧🇷🛥️
I was like.... why are you rebuilding everything on that engine if you don't know if the crank is good.... cuz the crank seems rotten
Not sure why you think the crank is rotten but did everything to make a video for you guys. It was a risk but it payed off. Runs perfectly fine. Never suspected a rotten crank or anything like as normally you’ll hear that pretty quickly. The rattling when it was on the water was the engine cowling. As it didn’t seal the best so it was vibrate unless I put my hand onto it
@@outboardfinatic oh oke i'm not hating my guy... it just sounded like a bad crank with all the ratteling
Yea I understand. But yea it was the cowling it didn’t latch the best. So it would vibrate like crazy with it on. But I didn’t show it in the vid but I could just put my hand on the hood and the vibrating would stop.
No one cares