K24 Swapping My 8th Gen Civic Si In 8 Minutes
Vložit
- čas přidán 14. 03. 2022
- CUSTOM TUNING, CUSTOM INTAKES, SOCIAL MEDIA AND MORE ⬇️⬇️⬇️
linktr.ee/Staticspeed
After 193K miles the timing chain on my Civic Si skipped, destroying my motor. So I took the opportunity to swap in a JDM K24A RBB-3 motor with 40-60K miles on it. In this video I will show you guys everything you need to transfer over in the swap from K20Z3 to K24A in your 8th Gens.
NOTE: We also swapped over every sensor from the K20 to the K24 which is not shown in the video. We did this just as a precautionary measure to make sure everything hooked up to the Z3 wiring harness
If you guys enjoyed this video make sure to drop a like and share it with all your 8th Gen friends who need this swap in their life 🙏🏻
#k24swap #k24 #8thgencivic #8thgensi #civicsi #k20z3 #kswap - Auta a dopravní prostředky
When you pull 2nd gear that’s when you know it’s not a k20 no more 🔥
Damn, these guys work fast, they don’t mess around. My boys would never get their hands dirty.
I know I am forever grateful for their hard work. Really saved me in my time of need
Awesome bro, I just bout a k24a from there today.
🔥🔥🔥
Can’t wait to get that antilag tune man, #STATICTUNED
Yessir!! Working on getting you a revision tomorrow brother
@@staticspeedproductions8087 sweet, car feels so much better than the hondata basemap it’s crazy
Orlando that we’re I’m at not to far from that shop 💪🏾💪🏾💪🏾
Hell yea bro glad to see you back and running , hmu I’ve been making tons of progress only thing is doing it myself it’s not so bad I would I’m 70% done can’t wait
Doing this tomorrow!! Do you have to cut the rbc intake manifold to fit the rbb3 head?
What spacers did you use for the rear motor mounts ? Or where did you buy them ?
Damn bro I been thinking of doing a swap but I would have to find myself a good shop first cuz I really don’t want to do all that work myself in my front lot 🤣
Yeah man definitely need a shop for this one it’s just way too much
I did mine in the back yard. Built the block in the kitchen and used a set of hand trucks to bring it out lmao definitely sucked balls hopefully u found a shop. I feel ya dawg!
🙂👍👍🤘🔥🔥🔥
How i do i go ab getting a tune from you? i just got done with my k24a swap in my 8th gen have flash pro but cant find a base map or tune to run
LFG! im pretty new to florida, link up sometime make some content/cruise around.
I’m in St. Pete wya?
@@staticspeedproductions8087 up in palm harbor
Nice man hit me up on IG @staticspeed.tm
Should of done the Type S oil pump and 50-degree VTC while the motor is out. I also would of done the timing chain, tensioner and guides. It's not a Honda if you can't do at least 8k rips.
Not gonna potentially sacrifice reliability of such a low mileage motor for a few horsepower. The motor will be getting boosted eventually. The motor can be pulled in 2 hours so it’s not a big deal to do any of those things down the road if I feel like it
@@staticspeedproductions8087 You have a mystery motor and no matter what are taking the word that it's low milage and that they were kind well taken care of miles.
VTC is a known fail point, just Google it with 8th gens. Everything I mentioned literally improves reliability, performance benefits are a side effect. Unless your arguement is that you would improperly installed the stuff or something. These were literally the first thing I did for my k24a2 in my eg hatch, thing runs like brand new.
Nice
ktune makes a header for k24swaps on 8th gen, no more header knocking on the firewall
So does PLM. I already had this PLM V1 K20 Header so I made it work. Only vibrates for about a week randomly and it hasn’t vibrated in months
2 hours huhmm . Yup am gna need at least 2 months
you're going to crack the header if it hits the firewall hard im sure
Yeah we’ll see how long it lasts not too worried about it
did you use the stock bolts or had to put longer bolts when you put the washers on the rear mount bracket so the headers can clear??
Stock bolts. Longer bolts would be a good idea tho
Yeah my skunk2 is touching the firewall slightly. Putting the washers does the trick?
Yeah that’s why I did it
@@staticspeedproductions8087 ty
Hey I saw that you went to jdm express to buy the motor, I bought my k24 from them yesterday, I got the k24A RBB-4 is there a difference from the rbb-3 and the rbb-4 ?
Pretty sure it’s the same motor just a little newer by a few months to a year or so
@@staticspeedproductions8087 oh ok so the internals are all the same ?
Should be yes
@StaticSpeed Productions how do i got about purchasing a k24a from this shop?
Give them a call, ask for Edwin, tell them Staticspeed sent you and ask how many they have in stock and pricing (407) 657-0040 you can either pick it up yourself or I believe they can give you a shipping quote
I'm almost at the point of pulling out my k20 and getting k24. Are you able to keep your z3 head with this build ?
Yes that will do the best combo. I wasn’t sure if my head was trashed or not so that’s why I just went K24
What block do you get if you want to run the k20z3 head
How many washers did you use for the rear mount?
5 on each
Sick, what’s the highest u can rev with the k24 without the type s pump?
7600 to stay on the safe side. Some people go higher but it’s pointless without 50 VTC
Safely 8200
@@staticspeedproductions8087 hey man what vtc are u running?
Stock 25 VTC
@@staticspeedproductions8087 dang .. I know u know the 50 makes more but really I mean looked about the same. That's impressive. Quick plain and simple, effective... Other then the known issues with chain/tensioner I bet it don't get much more reliable than that
Bro who’s ur boys. I got a fg2 in Orlando sitting needing a clutch job. Or a swap. It’s a k20z3 with 260k miles lmao. Still ticking fbo
@aaron_gorman99 on Instagram, But we are in Clearwater area. Would have to get the car towed over here
@@staticspeedproductions8087 Facebook? And yeah I’d tow it there and drive it back home lol
I dnt have Instagram
Try finding him Aaron Gorman
Did you use a k24a2 valve cover and oil pan gasket ?
K24 valve cover and RTV silicone goop gasket
@@staticspeedproductions8087 thanks bro, doing the k24 swap on my coupe this weekend.
Good luck man!
Aye man do I have to change my k20 cam sensor over to the 24?
Every sensor needs to be transferred
@@staticspeedproductions8087 just finding out the mechanic that did the swap didn’t change the whole vtech solenoid assembly SMH
Damn yeah the K24 one is missing a wiring plug
How much did u pay for the engine there?
How much was everything? I’m also at 193k and I think the timing chain is about to go
Everything included you’re looking about $1400 if you do it yourself and damn what a coincidence
@@staticspeedproductions8087 how much did the shop charge you? Im probably gonna take it to a shop too
@@K20Val Can’t talk about that but let’s just say no one on the planet would do it for the price these guys did. Can’t thank them enough so you either have to know someone or pay about $2,200 for a random shop to do it
By all accessories do you mean everything like alternator and all?
Yes everything that is ran by the serpentine belt
@@staticspeedproductions8087 so you literally only need the bare engine
Exactly
now rerun it with the 350z Hr😈
Once I dyno tune it on E85 I’ll make it happen for you guys 🤞🏻
I do engine work at my place gota shop on my property
Very nice I’ll get there eventually
Def could pulled it from the top
Only if we removed the radiator, A/C Condenser, and core support. Fitting the K24 in through the top would’ve sucked though
@@staticspeedproductions8087 ahhh shit dude k24 your right
Bad ass build dude. I’m gonna watch the videos see what else I can do to improve performance w/o forced induction
Thank you man, don’t hesitate to reach out if you have any questuons
Do you miss the z3 yet?
Not at all
@@staticspeedproductions8087 how come?
Tons of more torque I will do a review soon once it’s broken in
200 miles since chain swap? Damn… maybe it wasn’t done right? Low oil?
200K miles