NK01 / NK02 Tufting Gun - The gear is not moving smoothly or at all - Tuftinglove.com
Vložit
- čas přidán 6. 04. 2021
- This tutorial talks you through all the steps you want to check when your gear on your NK01 or NK02 tufting gun is not moving smoothly or not moving at all.
Check out the written tutorial here:
www.tuftinglove.com/helpcente...
Check out our shop: www.tuftinglove.com
Learn more in our Tuftipedia Helpcenter: www.tuftinglove.com/helpcenter
Visit us on Instagram: / tuftinglove - Jak na to + styl
This is the most confusing trouble shooting video, I’m not sure what they’re doing or why
Hello, my gun starts beeping when trying to tuft through monks cloth. When I turn the gear the gear by hand it does not jam and seems to move smoothly. When I press the trigger while it is in the air, it also seems to be running fine but once I place it in the fabric , it makes a beeping sound and will not work.
Did you find a fix? Or buy another one
Hi there. Thank you for the video and amazingly simple instructions. My problem with the gear continues after I used the second option, the cut pile one. The thing is, the gear is moving smoothly when I made it perfectly aligned, but when I tighten the screws, it goes back to not moving smoothly. What can be the issue? Thank you very much 💗
The screws on the side of the housing? Hmm, that's weird. Maybe something get's pushed together accidentally that should not? You can also send me a video and pictures to help@tuftinglove.com. So I can '' have a look''
Thank you very much, you're so helpful
Hello. My heat does not move at all and when I press the button it beeps. I tried all of the tips in the video and nothing worked. Any other suggestions?
Hi. My gear is still reallllly tight when I try to turn its 360 degrees
What could be another issue?
My gun is making a high pitch noise and the week will only move when its disconnected from the scissors. I just got the gun a couple weeks ago
Hello! My cut pile gun gear is really difficult to spin when getting to the scissor/cut position. Other than than it turns smoothly until getting to that point? I highly believe this is causing a beeping noise and also causing the machine to get stuck. Do you have any ideas? Please let me know.
Hey,
Sounds like you pit the scissorsclosing block too much to the back. Try loosening it and move it a bit forward. the scissors should really just close when they‘re at their outmost point. If the block is too much back. they close too early but the gear still wants to push them forward what makes it moving very hard.
Hi thank you for the video!! I tried to adjust the stop. However, I still have the problem, that the top bar does not stop at the same position every time it stops. Sometimes a little left to the Center, sometime a little right to the Center. In your Video it looks like the top bar always stops at the vary same position. Due to this problem the cotton cloth is cut every now and then. :( Do you know what the problem could be? Thanks in advance! Christina
Same
Hi there, the pin on my tufting gun seems to be almost grinding together with the scissors and the gun won't move up the cloth, rather it keeps tufting on the same spot, any solutions to this I'd greatly appreciate? Thanks :)
did you ever find a solution? I'm stuck with the same problem.
Hey I’m having a problem with my gun not stopping at the correct possession like usually when I let go of the trigger the needle is always ahead of the scissors and not its like my gun won’t stop on that position sometimes the scissors will be ahead of where the yarn whole is sometimes the will stick completely out ahead of entire needle is the anyway you could help
It seems like a have a quite similar problem : I still have the problem, that the top bar does not stop at the same position every time it stops. Sometimes a little left to the Center, sometime a little right to the Center. In your Video it looks like the top bar always stops at the vary same position. Due to this problem the cotton cloth is cut every now and then. :( could you solve your problem?
Hi amazing video, My cut pile gun started making this high pitch noise when I turn it on and it wont work. I did oil it but it seems the big white gear is stuck and wont rotate or move at all? pls help me
My gun is having the same trouble and I never did any adjustments to it :(
Hey the two of you, high pitched noise usually means the motor can't move because there is something stuck. Are you able to turn the big white gear by hand when the machine is unplugged?
@@Tuftinglove No I wasn't able to. However I took some screws off and was able to push the big white gear at a 45 degree angle (away from the silver gear that turns it) and was able to move the white gear. Seems like the silver gear is stuck. I checked and there's no loose yarn anywhere :(
Hey David, hmmm can you maybe make a video of the situation and send it to help@tuftinglove.com. Kind a hard to tell from here.
hello! I just got a 2 in 1 tufting gun and when I wanted to test it it started beeping loudly. I oiled it because as a solution they told me that it could lack lubrication but after that, the wheel did not turn anymore, and it got stuck. I don't know what to do. It no longer moves. I need help 🙏
Hi, can You fix? I have same problem
Hi - I have a new cut pile gun - when i first turned it on, the black gear is spinning but the white one is not. When i turn it off and turn the white gear by hand, it seems to connect and then disconnect with the black gear - what can I do to make the gears run together properly?
Hey Bash, sorry for the late answer. Most likely the gears are not aligned properly. You can do so by losening the screw on top of the switch. Then you should be able to move the small black gear with the motor (these are connected directly. So you need to find the right angle, to make sure the white and the black gear always touch but there is no force between the two.
Don't hesitate to send me an email to help@tuftinglove.com If you have problems solving it. We will upload a video for this problem within the next days.
@@Tuftinglove could you maybe upload that video soon? My cut pile is doing the same thing, the black gear and white gear are not consistently touching causing the white gear not to move. I’ve never made any adjustments to it
My gun spits out the screws from the wheel. Its insane.
the troubleshooting scks
Hi I’m still having trouble getting my gear to turn, it keeps beeping at me and going really slow. In desperate need of help here!!
Did you check all the points of the tutorial?
Do You have an AK-I or an AK-II?
hey my yarn is stuck under the white wheel, what should I do
Oh this happened to me too. Be patient with tiny scissors and tweezers... until everything is out. Good luck!
I know you may not see this in time but Please Help! My gun keeps cutting off and I really need to get these rugs made by tomorrow, I don’t know what to do and I’m freaking out. What could be the issue? Every time I start to use it the light just dims out. It has never done it before and it now decides to do it when I need it the most. Please help
Hey,
sounds like your cable is having a loose connection and it's only connecting the wires properly in a certain angle. Unplug it, check all the cable from the powerplug to the machine, might be there are cut somewhere and open the handle to see if the cableing inside the machine is correct. there has to be something loose, irregular somewhere
@@Tuftinglove thanks for the quick reply! I haven’t found any info on this issue. I will check the wires hopefully a simple fix. thanks again
My gear will not fully turn and I've not made any adjustments. The few ideas in the video have also not worked! Any other ideas please?
Hey Jasmin, have you loosen the scissors closing block fully and then it will still not turn?
@@Tuftinglove I've managed to get the block to go round but still now can't work out why the yarn is not cutting. Tried it with the block at every level!
Hey Jasmine, Did you also check this tutorial? czcams.com/video/U8tX69KTkRA/video.html If that still does not work don't hesitate to send me an email with some videos explaining and showing it to help@tuftinglove.com and I check there.
my gun still beeps for some reason any advice on how to fix
Make sure you can rotate it easily by hand. If that's not the case make the adjustements to do so. Also make sure there are no yarn scraps within the moving parts, it's cleaned and well oiled
What to do when the yarn is stuck in the gear ?
get tweesers, a tiny scissors, turn on netflix and be very patient untangeling :)
Hi is it still possible to get help here??
what do you need help with?
not everybody has the measuring tools….
Hey Jo, you can use any basic ruler or measuring tape that you have. It doesn't need to be this one. I just like it because it is small and handy :)
@@Tuftinglove can u please help me ???
@@Tuftinglove the part that presses against the fabric came out and won’t stay in
@@joszana1999hudson The Pusher underneath the scissors you mean? It's fixed with the little front black screw on the lower white moving block. In case you cant tighten it, check out our Scissors changing tutorial. The counterpart of the screw is placed underneath the scissors. So in order to be able to fix it again you have to take out the scissors. You can find it here: czcams.com/video/4xTfyNnSJxU/video.html
@@Tuftinglove okay yes the pusher under the scissors ! and okay thank u
Don’t understand you
what do you not understand?