Video

it's work! thank you so much for this tutorial. it's saved my life and my money <3

My gun spits out the screws from the wheel. Its insane.

Hey I need some help with my gun can you respond pls😭 my Gun fell and now it’s not gliding like it used to like at all it just stays in one place. What’s wrong With it and how do I fix it!? Thank you!

Hello! My ysrns is not feeding well between the two wheels- what can be causing this?

I am so greatful for your video, it helped me a lot🥰 Thank you 😍

Thank you so much! 🙏🏼🙏🏼🙏🏼🙏🏼🙏🏼

Thank you very much. Super helpful!!!!

What happens if the scissors closing box came apart. How do i put that back together?? Mine has. And i can't get the piece inside back.

Hi I am trying to change from the longest pile height 60mm to a smaller one and the feeding wheel won’t come off the same way it did with the shorter pile heights. how do you recommend removing it

I am over the moon happy about this. Been tufting for a bit and have been contemplating getting the pile loop - but now I don’t have to! Thanks so very much for this unbelievable hack!

Thank you 🙏🏾

Hi! Thank you so much for this tutorial. I’m wondering if my scissors might be rusty… Should I be able to open them and close them without any effort when they are out of the gun? I asked because my gears are not rotating freely, and I think it’s because the machine is having a hard time opening and closing the scissors

Thanks a lot , this is the best tutorial in the entire of CZcams videos ❤

🥔

THANK YOU!

Thanks very much for this! Super helpful to stop fearing the sheering machine :)

Good day, your tutorial videos are so helpful. What if the sensor wire is not showing as yours so how do adjust the sensor?

Thank you so so so much i was fighting with this problem ❤

I don't know what kind of compressor to buy for this device, can you help me?

I don't know what kind of compressor to buy for this device, can you help me?

Can you make a video where you doing it with the ak duo

Do the nails that grip the primary fabric have to be in a angle? Or can it be 90° ?

what is that

Merci😊 très instructif

Im having issues with curves, its like trying to draw a circle on concrete, the gun goes everywhere, what could be the issue

Just some advice, you should never adjust the threaded rods on any tufting machine. This really puts people that do this in a tight spot as you can not easily revert back as it is now set at a random length.

Hello Jenny! You explain it very clearly. I just didn't see which part of the scissors should be at a height of 18mm from the pusher. Do you mean the very tip of the scissors or the corner? I am grateful in advance for the answer!

Здравствуйте Дженни! Вы очень понятно объясняете. Не увидела только, какая часть ножниц должна быть на высоте 18мм от толкателя. Имеется в виду самый кончик ножниц или угол?

You are amazing teacher 😊

Thank u for your video. U help me understand problems with t-gun

اعلم انك لا تتحدثين العربيه ولكن اردت ان اشكرك بلغتي شكرا من القلب شكرا شكرا اسأل الله ان ينور قلبك بالاسلام لكي تدخلي الجنه معانا شكرا لقد ساعدتني كثيراً 😭❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

Thank you 😭🩵🩵🩵🩵🩵🩵🩵🩵

Thanks a lot for every single video on your channel. You are literally helping A LOT more than the producers of the machines. Thanks to your videos, I am able to solve the problems I encounter while working, and my enthusiasm for engaging in this super fun method of production has increased. 🙏

MAN-IP-YOU-LATE 😅😊

noted. Inhave been and will continue to use my favorite firearm lube.

hiya my guns arrived with the top of gun distance between bolts at 5cm/50mm, dyu think this is why it's so uneven when loop tufting? and if so how would you recommend adjusting this? thanks! ☺️

Thank you very helpful ❤

би ийм ноосон утастай болмоор байна

I agree, you are a great teacher!! 😊 Thank you!

What compressor do you use for the AK-III

What compressor is needed there is so much confusion as it get stuck with a 90psi -130psi

What if the thing poped out 🥲 In what order is it arranged?

What is the metal hook piece under the scissors? Mine came off idk how to fix it😢

Hello, I have a loop pile machine, can I turn it into a cute pile myself?

Very helpful. I was able to get my gun back to working properly after some yarn got caught up in it, thank you!

You are the best teacher. None better. This video was so thorough for a beginner who is going to start her first rug tomorrow 🙏 Finally! 😊 Thank you!

Can you do the same with an Ak-II?

Kindly assist me with the details on arrangement of the scissors' components on a turftingt machine