Video není dostupné.
Omlouváme se.
How To Turn Siren Chirps On & Off, Compustar Alarm CM7000
Vložit
- čas přidán 16. 08. 2024
- How to turn confirmation chirps on and off (Silent Arm/Disarm) on a Compustar car alarm with a 2-Way remote. I'm using the Compustar T9 Remote Control, but this will work on all 2-way remotes such as the 901-SS, T10, T11R-SS and T12-SS.
➡️ There is now a THIRD option beside Enable/Disabled for "1-16"! It is called "Silent Alarm." This will page the remote, but lights and siren will NOT sound and flash when the alarm is triggered. Hold Trunk Button for 3 seconds (instead of tapping unlock) following the 16 chirps to select this. It may not be available if your firmware is too old.
➡️ I show how to program the Siren Muting option to enabled using the remote control, for newer models this option is disabled by default so turning the siren chirps off will result in an error until this option is enabled. The programming will likely be required for all models flashed with the latest firmware.
⚠️ DISCLAIMER:
Use of the information in this video is solely at your own risk. The creator of this video assumes no liability for any property damage, injury or expenses incurred as a result of any of the information contained in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result.
The creator of this video makes no claims, promises or guarantees about the accuracy, completeness, or applicability of the procedures and instructions contained in this video.
Any injury, damage, or loss that might occur as a result of improper application, improper use of tools or equipment, or from the information contained in this video, is solely the responsibility of the user.
Music:
Happy Indie Pop by WinnieTheMoog
Link: filmmusic.io/s...
License: creativecommons...
If you enjoyed the video, please give it a *thumbs up* 👍 Your support is *greatly appreciated* .
Great video bit I have yet to see a video with alarm going off by vibration. How sensitive is alarm feature?
Thank you! My neighbors will be very grateful!
That's great!
Thank you so much …. I hated that chirping noise & now I feel like I have a new system. Great 5star video
Neighbors get annoyed with it too if you go in your car a lot. It's pointless to have it with a 2 way remote other than to let people know you have an alarm.
How do I lowere and raise the volume on the alarm?
Thanks for the video. The chirps were so damn annoying
I have a compustar 2305 trying get it out of silent mode ?video only helped to get out of valet mode, but Video not helping to get chirps or siren back on
Love these quick setup tips. Question though: Would you be able to tell me how to change or lower the sound that the remote makes when the alarm is triggered (is so loud)? Thank you in advance!
Sure I can make a video on it. Which remote do you have? The T9 that I have can only do vibration mode, but if yours supports volume, it's very similar to enabling vibration. I can have it up within a couple of days.
I'll also do a video on lowering the siren Chirp volume, besides turning it off, it can also be toned down, it has 3 settings.
@@CleverFix Thank you so much for your speedy reply. So once I got home I realized I got the remote 2WT9R-FM I have the compu 7900AS been having it already for 2 weeks. I tried to mute off the chirp off and it failed. I might have to reach out to the dealer where I installed it. I will be on the lookout for your video. I appreciate your time very much. 🙏🤟
@@felixcruz6829 Yep, it will fail on newer ones unless you do the programming. Dealer will do what I show in the video to enable it by changing option 16 in menu 1. On older ones, menu 1 option 16 didn't exist so it worked by default.. but they decided for some unknown reason to make it difficult. I got the T9 also, you won't be able to turn the volume down just make it vibrate.
I’d like to know this also. I have the 2WT10R-SS. Please advise
I've got to CompuStar q9 and I can't seem to get it to work.
This does not seem to work for me. Any ideas?
Me either
Really nice video 🤝🏻
Thanks for watching!
Please can anyone help. My compustar was installed professionally. The 2 way communication seems to be faulty. It actually starts however it doesn’t indicate that it has started. Nothing seems to work - for example when I press the lock 🔒 it doesn’t work even unlocking it as well. LCD is not lit. It used to work but now it doesn’t work.
Appreciate the tip man it really helped lol
Buenas ayúdame como desactivo el encendido a distancia del control model 2wq900as place
Thankyou!!! Compustar was no help!!!
I need your help please. How to select option 4 on crank start. Mine is over starting help
Where can i get that manual you have? I have searched all over for that so i can make changes without having to go to the dealer to adjust things.
How to turn my voume up?
Will it work with prestige?
Thank you!
If possible., can you please explain how to navigate to next feature groups # 2 through #4? using remote control?
If there more than 2 feature settings., how can we select and save that settings? For instance 3-7 ( Siren Duration Upon Alarm Trigger) - default 30sec, 60sec, 120sec where I'd want set to 120sec using remote control.
Thanks again.
Once the lights finish flashing:
Option 1 = Lock
Option 2 = Unlock
Option 3 = Hold Trunk for 3 seconds
Option 4 = Tap Key Button
So "Hold Trunk for 3 Seconds" is the 3rd one. which would be 120sec
For full details, see the manual, this is for a CM7000 (Make sure to use the one for your alarm, since the options are slightly different depending on the model):
images.idatalink.com/corporate/Content/Manuals/COMPUSTAR/CM7000_Full_Install_V3_15_2016.pdf
Instructions are on page 57, and they include how to enter all Menus from 1-4, under "How to Program Options on 2 Way Remotes with Separate Lock and Unlock Buttons"
I'll try to make a short video for the siren extension programming, that may be something many people are interested in it since the default is only 30 sec. Thanks for the comment.
I don’t know why the remote beeps when I’m not driving the car. Do you know why?
What does it show when it beeps? Is the battery low?
This is awesome
Thanks
Can I do this programming on a CM-DC3? It was installed way back 2 years ago and I do have the t9 prime remote.
No sorry, see your manual here: geeksquad.compustar.com/live/wp-content/uploads/2017/11/FT-RS-HCX-FT-DC3-HC-EN_201711062.pdf it is only programmable by interface. You need menu option 3-10 (page 26)
Thank you.. Im also trying to figure out how to activate the autolock or passive lock because sometimes i forgot to lock manually my car.
@@learnbasic2197 You need a Weblink USB, www.ebay.ca/itm/iDatalink-ADS-USB-Weblink-Updater-Computer-Cable-ADSUSB-BRAND-NEW/283441245456?epid=1424478343&hash=item41fe6a2d10:g:8M8AAOSw0Kdcpl7O
Your unit can't be programmed by remote. Passive, and siren chirp etc, all options should be available through the weblink. The seller should be able to guide you how to download the software and connect to your unit, you will need a laptop and connect the cable to the remote start module, then you will get options to set chirps, passive, etc.. it's quite expensive though considering all you get is to set some options. It's unfortunate Compustar didn't make these options remote programmable.
I had someone install it but shouldn't I be able to program remotes using the book guides it came with like u did?
Yes you can do your own programming if you feel comfortable. These procedures are outlines in the installer manuals which you can find online. They recommend the installer do it because they're experienced, but with the current situation, I think most people will be trying to do as much as they can on their own.
How do you enable the passive lock on the t9 remote, also is there any chance you can post a video or a photo of the full enable option instructions I as I didn't get the guide with mine. Thanks!
Here: www.compustar.com/live/wp-content/uploads/2015/09/2WLCD-SepLU_QuickCard_2013.pdf tap Unlock and Trunk together (not hold) , but it has to be programmed. Programming instructions here, www.staub.ca/pdf/sku/cm7000_full_install_2-12_en.pdf option 1-08 (page 30). Yes I'll consider doing a video but it will take a few days, someone asked me for a video on extending remote start time as well so I can film them together. You'll have to enter menu 1 and go to option 8, there are instructions in the same PDF how to enter each menu, page 50 or so.
These videos are awesome! Thank you! I have the Pro T13 LCD remote. I found the CM7 Master Installation Guide Version 4.0, that's the latest one I could find. It doesn't list my LCD, 3-button remote. How do I use the Pro T13 LCD remote to program options? It has only 3 buttons. Thanks!!!!!!!!!!!!!!!!!!
I've never seen a guide for 3-button, only 4 because an option can have 4 different settings, so with 3 buttons you wouldn't be able to select all the possible options.. perhaps you could order a cheap 4-button remote from ebay that matches your antenna receiver ?
@@CleverFix No. I have the T13 remote. The only available resource is provided by the installer, which I got from him. Thanks for your videos, though, they were quite helpful!
I also have a T13 and can't find any info on how to program things yourself.
@@CORZER0 hi, do you still have that document for the t13? mind sharing it?
@@scotchbonnetfk8 I'll look bro
Just added some G15 PRO remotes to my CM7000 to be able to set this (1-16) program but when pressing the key button it won't let me get past 3 presses before it plays the three back to me. I've tried slow and rapid. Always stops at three.
That's strange. The car is unlocked when you're trying this right? Normally the "play back" happens after a wait period.. are you getting a chirp on each press 3 times in a row? Have you tried 2 presses and then waiting? Almost sounds you're in a different menu, but no menu has only 3 options.
@@CleverFixYes unlocked first. I can't understand it. I tried waiting (a second) between key presses for chirp and flash and also tried just going faster - both end on three. Compustar told me they don't trust consumers to do programming and said to visit an installer... I will try two - but sometimes it results in the alarm going off for a short duration. I need to drive to a place where nobody cares - or pull the wire off the horn.
Great video.
Where do you find the program menu?
I have a Compustar 4905 installed in my 2014 Hyundai Tucson. Everything works great but I’m not getting any chirps when locking and unlocking my car doors. Thanks.
Do you have an alarm system Compustar, or just remote start? Some don't come with a siren. If you have alarm system, then turning chirps on/off depends on your remote, which remote do you have?
@@CleverFix Compustar FMX (G15) remote.
@@CleverFix
Tried the troubleshooting steps.
@@calinubro See your manual here, page 5 , technically it should work.. but maybe something's wrong on yours: www.compustar.com/live/wp-content/uploads/2017/09/Document_20170808_100835_RF-P2WG15R-SSFullUserManual.pdf
It's a very sensitive alarm system. Loud motorcycles, noisy cars and trucks and low flying jets always set it off. Is it possible to remote lock the doors without the alarm set and or lessen alarm sensitivity ?
You can turn the shock sensor off, see my video: czcams.com/video/1SAoZ365oFQ/video.html OR You can turn the sensitivity, instructions are here: help.compustar.com/s/article/Adjusting-Compustar-Arctic-Start-Alarm-Shock-Sensor You probably have a DAS or DAS II so I think those will be the instructions for you.
@@CleverFix that was the solution...thanks !
i have two channels, thanks again.
Question: If I disable to OEM horn from beeping when I lock my car, does the alarm still chirp or is it connect to the OEM horn?
If your alarm chips right now, it will keep chirping regardless of the horn settings on the lock/unlock from your car manufacturer.
@@CleverFix ok thank you for replying I appreciate your help
How do I stop my alarm when it goes off? Sometimes I accidentally hit the alarm button and it goes off and I can never figure out how to stop it. I just keep hitting buttons until it works lol. Help!!!
It should be the unlock button!
My shock sensor went off for the first time but my car alarm didn’t. The 2 way control made a chirping sound
( czcams.com/video/rx4GBc76Ym0/video.htmlsi=BXZPQjG4gnQEfqgw )
is it normal for the car alarm not to go off ?
There are 2 stages to the shock sensor. If the first one is triggered, then the car makes a few chirps and the remote sounds. On the second level the alarm is triggered fully and the car siren sounds for 20-30 seconds.
So yes it could be perfectly normal if the bump was not too hard.
It's also possible for the siren to be set on "Silent" in which the car siren will never sound, but the remote will.
How do I turn off the emergency lights while the car is running? When I use the remote start to start up my car, it works but the emergency lights start flashing for those 15 minutes.
How can I start the car without having the lights flashing?
It's likely the parking lights turning on and off, rather than emergency lights. I know it's hard to distinguish between the two. It's on page 29 and 57, in the manual images.idatalink.com/corporate/Content/Manuals/COMPUSTAR/CM7000_Full_Install_V3_15_2016.pdf Option 3-01 . The instructions are all there but you'll have to do some reading,...
You have program group #3 feature #1 (Parking lights While Remote Started)
To enter group 3 it's (Lock + Key for 3 seconds then Lock + Unlock for 3 seconds) that will get you in Group #3. Then tap Key just once, and WAIT until it chirps once and parking lights flash once.
Then tap Lock for Option 1 which is parking lights ON, OR Tap Unlock for flashing. OR Hold Trunk for 3 Seconds for Lights OFF.
I recommend going over the instructions to get familiar with the process and make sure you program it correctly.