@@xpsgarage spent all morning taking apart and reassembling the carb. Needed a new battery as well, oops! Got her running but the idol and rev are not acting right. My Governor linkage is sloppy to say the least. I think a Governor rebuild is in my future
I have never seen a 8N with the breather on the left side. I bought a new proof meter and cable and the inner cable was too short and had to by a universal, we’ll see if that works.
I have an 8n. I had to replace the carburetor and now it tries to die when go up hill, I did replace the fuel filter and readjusted the carb many times from factory to extreme with no luck. Any ideas? Thanks!
Great video Working on my 8N -- Tractor surging Installed new after market carb -- half the weight of the marvel ( will rebuild ). Removed governor, cleaned ( wished I watched video before --could have taken it apart -arms are loose and play in spring . Where do you get brass shim ? Re-installed governor -- still surging. Ordering new governor -- will rebuild old one when I have time this summer. Really helped me understand all components. Thanks
I bought A2N 1946. And it ran good when I bought it. I left the guy use it for 2 weeks. Went back to pick it up and it backed fires. And it will not stay running. Do you have any ideas? What might be wrong?
I'd make sure you have good fuel flow to the carb and would probably also drain the carb to make sure there is no water in it. After that check the spark plugs and ignition to make sure you have good fire.
@@duanebolen543 Have you checked all the wiring to and from the coil? Do you still have a resistor block in the power line to the coil? They have been known to go bad.
I don't think there is much adjustment to it. Make sure there isn't any slack in the spring and that the arm is not all sloppy. The adjustment is in the throttle linkage. Once you have the throttle set then the governor just moves the throttle to maintain RPM.
If its brand new, likely its an overseas (India or China) model and you may be in for some heart ache with its performance. Another video I found said that they salvaged a brand new overseas model by tearing it open and properly shimming the shaft which they found wasn't shimmed for preload at all. Good luck.
Excellent video!!
Thanks!
This arms me with the knowledge to dig into my 1947 8N….great video, thank you
Nice job. I love these 8N tractors.
Thanks 👍
Never knew much about the govenor. Now i know a little
Thanks
Great video, very helpful thank you
Best damn video ever!49 8n
Excellent you should be a shop teacher that old girl is looking newer and newer 😀🇨🇦
I wish your videos and CZcams were around 20 years ago when I had to do this to my 42 2n
Youngsters today just don't realize how hard it used to be to get good how to information.
Appreciate the video learned ALOT for my 9n I just bought
No problem. I hope you enjoy the new tractor.
Parts are so dam high now, I finally quit buying and rebuilding them because of the price 😢😢😢
New sub! I have a 39’ 9n. It is running like a turd and I just put a new carb on and can’t get it to keep running
Did you check the ignition system? That was the first thing I had to fix on mine.
@@xpsgarage spent all morning taking apart and reassembling the carb. Needed a new battery as well, oops! Got her running but the idol and rev are not acting right. My Governor linkage is sloppy to say the least. I think a Governor rebuild is in my future
I have never seen a 8N with the breather on the left side. I bought a new proof meter and cable and the inner cable was too short and had to by a universal, we’ll see if that works.
My ‘47 8N is also a left side breather
I have an 8n. I had to replace the carburetor and now it tries to die when go up hill, I did replace the fuel filter and readjusted the carb many times from factory to extreme with no luck. Any ideas? Thanks!
Is the arm from the governor to the carb opening the throttle when you start to go up hill?
Great video
Working on my 8N -- Tractor surging Installed new after market carb -- half the weight of the marvel ( will rebuild ). Removed governor, cleaned ( wished I watched video before --could have taken it apart -arms are loose and play in spring . Where do you get brass shim ? Re-installed governor -- still surging. Ordering new governor -- will rebuild old one when I have time this summer. Really helped me understand all components. Thanks
The brass shims I used were old feeler gauges I have for motorcycle valve checking. I usually get them from McMaster-Carr.
Do you have a fitting size and thread for the oil line.
The one going into the governor? It's a 1/4 Tube-1/8 NPT Inverted Flare Elbow
I bought A2N 1946. And it ran good when I bought it. I left the guy use it for 2 weeks. Went back to pick it up and it backed fires. And it will not stay running. Do you have any ideas? What might be wrong?
I'd make sure you have good fuel flow to the carb and would probably also drain the carb to make sure there is no water in it. After that check the spark plugs and ignition to make sure you have good fire.
@xpsgarage I already did all that an cleaned carb I think it's the coil, on six volt
Has new plugs
@@duanebolen543 Have you checked all the wiring to and from the coil? Do you still have a resistor block in the power line to the coil? They have been known to go bad.
Ok, is there a governor adjustment????
I don't think there is much adjustment to it. Make sure there isn't any slack in the spring and that the arm is not all sloppy. The adjustment is in the throttle linkage. Once you have the throttle set then the governor just moves the throttle to maintain RPM.
I bought a complete new governor for $112.00. On eBay.
If its brand new, likely its an overseas (India or China) model and you may be in for some heart ache with its performance. Another video I found said that they salvaged a brand new overseas model by tearing it open and properly shimming the shaft which they found wasn't shimmed for preload at all. Good luck.
Have you tried it yet? Some of the aftermarket ones don't work very well.
If you are using 1/2 inch it's a 5/16 bolt 🔩 just so the people understand. 😊
What did I do? Say it was a 1/2" bolt instead of saying it uses a 1/2" wrench?