Video

Good stuff Bubba. Thanks ❤

Should have stopped at the base color amd. Ot added clear. Looked better

Will this unlock the radio?

The 11 & 12s always looked cheap to me. I hate all the plastic on the outside

How the hell did you get the new PCM to plug back in? We have three guys and have spent 4 hours trying to get it back in.

I went to dodge to have this done. To replace park & signal light an they said it would cost $1400!!!!!

Great video big guy couldn't figure why my seats wouldn't set,your video did job 👍🏽

Showing the cover and the bolt underneath was a life saver that wasn't in my Soler instructions...THANK YOU!

Am I the only person that has problems with the seat back latching?

Just installed the 4dTech start-stop eliminator in my 2020 Chrysler Voyager. The 4Dtech installation video does not allow comments, and now I know why. It takes a while to figure out which connector to remove. And be very careful you don't drop the screws because you will never find them again. Better to use a screwdriver than the 7mm socket recommended. Otherwise it is a simple operation.

If you have a platinum there is no rewiring to add the center high mount camera. You just have to disconnect the plug and plug the new one in and some forscan changes. The plug is a little pain to reach but it's not that bad. Altogether the worst part of it was figuring out what to change in forscan.

Hello, do you know where I can purchase the bonnet shock absorber?

Anyone know how to get the service air bag message off ?? It keeps appearing after I installed the tazer

"Yay us" had me ROLLIN!

If I were to use the silicon would I put it around it before installing the plug or from the outside after installed?

I got mine flying pretty good. Of course, now is 2 years after this video, but anyway, I digress... I have a fusion 180 that is almost, well, pretty much, unflyable. Sent it back to HH and they said it flew perfectly for them for 2 batteries worth. Sent it back to me untouched, only to have the same, wanting to bury the rotors in the ground on spool up, then have to hold lots of right stick, and as the flight progresses, have to start holding left to the point I can't even go any more left, and then have to land. Something DEFINATELY not right! Now, the good news..sort of.. I got an Infusion 180 as my first heli, like you, after many years. Used to have (well, I still do) a Thunder Tiger Raptor 30, and a zoom Shogun, anyway, That Infusion 180 flew like CRAP!! Same thing with trying to bury the rotors, was an ugly mess! I got in touch with tech support back when they still had phone help, and the guy set me up with a new program for my radio that fixed EVERYTHING! Gave me all the proper telmetry I wasn't getting before, no more dumb spool up tip diggin' tendencies, the things a kitten now! lol So, I guess what I'm saying is, it's either something in the bind, or something in the program. I just wish those guys could have loaded whatever flight data they were using, on to my card which I had sent along with the heli for 'repairs'. Now it sits on my shelf, waiting for me to learn enough about all this stuff to take a viable, educated stab at fixing it.

Nice how-to. But I don’t see what the benefit of the quick release is. Does it make it easier to remove the can to empty it?

Did you get any gas smells inside the car?

Here 4 years later watching this video. Well done. Thanks for the info.

stick control had no responds,crashed hit a pine tree,check heli the rear blade were gone ,not because of lose screw, but blew off the motor shaft .

Thank you very much! Got a new one and have been trying to figure this out!

I know you showed adding anti-seize to the lug bolts... just be really careful NOT to torque to the same factory spec, as anti-seize completely changes the required torque. Thanks for the very helpful video!!!

This shit gave me cancer to watch, but it was informative

Life saver

BIG QUESTION i’ve had mine for 2 days and codes came up 420 and 430 shop said they couldn’t find any leaks …. NEW SHOP??? or what

Is this a 2022 model? If it is where is the factory BOV

It's not you. I had the same issue with streaks. Wasn't the process.

Fantastic video. Thanks! I have an XLT without the B&O sound system, so there's lots of room for my junk.

You cut it wrong.

Does anyone know the thickness of the small bracket part of the release kit, the thickness of the keyhole inside the bracket, and the width of the keyhole's limiting section? What are the dimensions of the square-headed pin cap and its shaft diameter for the latch on the new F-150? Will they fit accurately together?

2018 and newer 5.0 have dual port injetion and the catch can is no longer needed.

We did ours on 17’ Infiniti Q60 coupe n we let it cured for 3 days n it came out really nice 👍

Hey do you upgrade the top bearing ? on the driver side. Mine is making noise have u had any problems with them making noise

Great video. I always disconnect the battery when working around those airbags. They go off and hit you, they will break bones or worse.

Thanks for your video! It helped me install mines today on my 2023 Rocky Ridge F150 5.0L V8 Coyote! Unfortunately I was losing mpg after this setup until I researched why. And that’s because lack of crankcase pressure releasing from my engine. Simple fix. I just purchased UPR’s Crankcase Breather Kit One-Way Valve Billet that replaces your engine oil valve cover and I definitely noticed a difference with my mpg and how my truck was running better! You almost can’t install a catch can without one! They run hand in hand to help relieve that crankcase pressure.

Yo appreciate da bruh been tryn figure da out for months

Does the link you provided include both driver and passenger side kits??

This was great thank you. I had the check valve installed backwards and couldn't figure out why the can wasn't pulling any liquid! Thanks for this!!!

Thanks bro I just purchased my 2019 today and my seats was aaaaaallllll the way low from previous buyer lol

Where did you order the hood scoop from?

Didn’t have to scuff or prepare the surface at all?

Solid presets on the SiriusXM and nice video showing the OCDplug screen protector. I'll probably scoop one up for my 21 Lariat!

What size pipe he used to replace it with ? Was it 2.75” ? Im trying to do this myself and save 300$

Any difference between the CV Fab vs Whipple Intercooler?

just bought my truck yesterday, one question, on my other truck (silverado 2021) it had a high and low pressure pcv and i originally hooked up to the low side that hits the intake, i learned later that the other high pressure side is where most of the oil blows by and i had to completely rework it to the other side. Did you install on the side that actually gets the majority of the oil blowby?

Dude this was one of the best install videos I have seen. Straight to the point and do a great job explaining everything.

sure it wasn't cause the was open?

How did the paint and the stickers hold up?

Bless your heart 😂😂💯

Looks great how did the G2 hold up over time? I wash my wheels about once a week I am afraid of fading..