Video

This exact compensator is causing my AR problems . I think it causes to much pressure redirected back .

I bought a 290 Winchester and it is a short long and long rifle 22 rifle it's going to have to go to the gunsmith if after a good cleaning doesn't get it working again

Been looking for the older ones alarm for 7 years video do you think they still make them sounds like yours was brand new

i love it when channels use the scientific method to test things.

Great video how does that gun make out on hollow point 22 bullets?

I would contact the company and forward them your findings. Needless to say, those are nice looking grips and probably need some tweaking to make those just right. If High Stamdard could make those in the 1950s. Then I am sure a company could easily rival or even beat the quality in 2024.

Wow, I could tell the rate of fire was higher in restrictive mode vs bleed-off.

Will this work on a AR 15 rifle 16 inch 556 ?

I use these gb on my 556 guns and soon to be my 308 build. Excellent illustration of the bleed off mode, I have to explain this to customers at the range fairly often.

I own both and the a22 is bad as the 512 is good. The a22 is an engineering failure in every way. It is almost guaranteed to jam on every mag.I even sent it back to savage twice and they sent another new rifle that was worse than the first.I refuse to waste my money on another savage product. It’s so bad I won’t even sell it to someone else.

A lot of the Chinese ones off ebay are steel and nitride finished too 🤷🏼‍♂️ I have a few and they're build well

Suppressor friendly!👍 Wondering if upping the grain high brass to maybe 124 gr. would make any change?

5 star video

Why do people insist on making comments that are not true Remington 550-1 also shoots all three

Thank you for sharing.

i used th e 45 grip type in the navy,pisttol team, when i was a midshioman 1968

Omg!!! Please complete one full thought before jumping around! Your too hard to listen to

Looks like fully loaded is gone?

Mine came with the head of the cam pin slightly canted. I barely noticed it once I finally got all the parts for my build together and never even shot it and I had bought it so long ago that I don’t wanna hit them up and they think “Oh sure you got it like this” but I bought and it’s never been fired. Yes I cycled it sure enough trying to figure out which side the cant would lock up best but then seeing this video makes me think it is supposed to be perfectly perpendicular. So then I checked the specs sheets and said ah fu me.

Ruger is better,

I have a brand new one i purchased several years ago but didn't shoot until now. It will not cycl 22 short or CCI Standard velocity. Im guessing it may need a break-in period. At least i hope so.

Hammer forging is not how a barrel is rifled hammer forging increases hardness. They're both button rifled.

My question is did the accuracy improve? Cavedweller went from the factory synthetic stock to the Boyd's on an A17 hmr and got dramatically better accuracy

Colt 9mm isn’t exactly standard

Too bad this has been discontinued in the US. Nobody wants to sale their used models either. I always wanted to add this rifle to my collection and was finally ready to purchase but never imagined CZ would nolonger offer this model to US consumers. The CZ 512 is available in Australia and New Zealand and will cost a little more than $3,000 to import. As a huge CZ enthusiast I am very disappointed and feel like CZ has let down the US consumer. I'm rethinking my opinion of CZ. The only other 22 WMR semi-auto rifles are less than desirable with CZ and Ruger both exiting the US market. The only comparable manufacturer in the US is Volquartsen and their models are way overpriced. If CZ would bring back this model to the US as a limited edition I would pay very handsomely for it. Until then my CZ collection is incomplete and I am very disappointed with CZ.

This is such an awesome video. Thanks for all the work that went into this

Very fair comparison but I would disagree with the "takedown ". I'm sure some people will disagree but I'm more concerned about cleaning the rifle, not just taking the stock off. All you need to do with the savage is remove the dust cover, twist the return spring and the bolt slides out the back. This will allow you to clean the rifle from the chamber end forward, instead of the muzzle end. The CZ is more similar to a 10/22 or marlin 60. It can be cleaned from the chamber end, like the savage but the bolt spring is a bit of a challenge to get in without bending it (same as marlin 60s). It is true that you'll have to remove the scope on the savage to clean it but that's only if you select the right/wrong scope. I have a Burris 4.5-14x42 , Burris 3-9x40 aa well as most of my other scopes that do not interfere with cleaning/removing the dust cover on my savage A17. I wish I had bought the CZ, I will admit, but it should also be mentioned that CZs are not nearly as easy to find, at least not for 100 miles from my area. One more drawback of the CZ is it comes with a 11mm dovetail for mounting a scope. The weaver bases are far more sturdy..

Fantastic breakdown

Where you ordered the buffer spacer

Try filling them with flour or colored chalk dust and some air for exploding targets

I don't understand the reset trigger pull. Reset is let-off, no? He measures 4 lbs, primary trigger pull, then it looks like he should be getting 4 lbs again, but it's much higher. Whaaa? How can let-off be measured as pull??

For a 552 owner this video provided valuable information thank you!

Where did you go??

Thanks for this video!

VERY DANGEROUS GUN!!! MANY LIKE ME HAVE HAD THEM BREAK UNDER THE LEVER MAKING THE TRIGGER GO OFF AS SOON AS THE GUN IS CLOSED!!! I HAD MINE POINTED IN A SAFE DIRECTION AND THE 12g and 22 WENT OFF AS SOON AS THE BARREL CLOSED! IT'S HAPPENING OFTEN, as ive seen others reporting the same PROBLEMS with the M6

I just got one in the pawnshop I pay $400 I don’t know if that’s good or bad but it’s a good looking Remington speedmaster 552 no scratch, or dent on the gun my serial number starts with serial number A1861080 What year is your rifle it says made in Illinois New York on the barrel one part it’s got REP something and on the other side, it’s got some other letters and it says 78 I was wondering if it was made in 86 or 80 minds looks like yours

thats slick, wish someone would bring this back, thats the best looking and simplest in design bullpup ive seen so far. thats neat, nice gun!

Its not the only short long lr 22 dont forget rem 550-1 it was 1st

Thanks for the incredibly informative review. Awesome

That high ping from the piston is something else, like polishing steel with sandpaper

Do you know if it will run well with Fostech's 9mm conversion upper??

I have one with the brass deflector on the side- great shooting little rifle!!

Fantastic!

Incredibly helpful and informative! Really, great job! Subscribed

I bought it and it was trash ! Don’t waste your money ! Stick to the UpLuLa

Hi, great videos, would you say it’s worth installing this on 11.5 inch sbr which will always be used with a suppressor. Brand is Daniel Defence ddm4- 7s.

If you have a binary regardless how its made just be safe with it. Know what you have. Dont be an idiot. Always keep gun pointed down range. If your going to disassemble the firearm mid magazine and your dumb enough to keep your finger held back the entire time you should just give up your guns. Nothing wrong with a single disconnector. Just be mindful of what you have and dont be an idiot

I see genuine Troy’s going for 80-150 used

Problem is doors and center bump area which consume 70 percent space. Still no one figured out problem

you did a great video very thorough