Thanks again......Great Video and info.....Hope everything is going well for you cause .I just noticed you haven't been around in several months.....You Can't leave us now .....We're loving your videos !!! Thanks for all that you have done.....and hope you continue to post videos.....
Thanks. It has been too hot and buggy at our range. Then had a list of "honey do" projects and other life events taking my time. Have a bunch of items in the shop to review. Thanks for the kind words. I will be back in production soon.
Thanks for the great reviews, tests, and videos. I purchased several of these after seeing your video for endomag. Got to say I haven't had and issues with them so far.
@@MichaelBellmbell556 If I were to run an 20inch barrel on a collapses butt stock, what buffer should I be using?? SPC Vong 101st 3rd, Bridgrade For Campbell, KY
@@bravocompany2196 I have used a standard 3 oz carbine buffer with a standard carbine length spring on 20" barreled uppers with no issues. It depends on the gas port size.
Our Endo mag has worked great will all types of ammo, even steel cased Tula, Biggest issue I see with endo mag is premature ejector wear, I suspect 1 magazine insert is only going to be good for a couple thousand rds before needing a new Endo unit installed in it. We have 500 rds+ on ours and it still works, we will see for how much longer.
This is awesome! Thank you very much..I had some concerns about the quality initially and general wear and tear..how have these held up for you thus far after a few months?
been thinking about getting these and a cmmg rdb bcg/barrel but every time i do, "just" an upper it always turns into a complete gun. I always seem to justify it some how (have extra buffer or whatever) well that's almost a complete lower, what the hell... still on the fence but leaning towards one that takes glock mags. Big Thanks for the vid Mike.
I'm a little late to the show but would you be willing to test the Fostech echo trigger with the endomags? Considering having a correct bcg to clear the trigger lock. If you don't have a correct bolt carrier group, foxtrot Mike makes one for about $100.
According to CMMG...... "Compatible with CMMG 9mm Radial Delayed Blowback uppers only". I have not seen or handled one so I am not sure of the differences.
I used the 9mm spacer in the buffer tube with a standard carbine spring and standard carbine 3 oz buffer. I covered this in my initial Endomag video but forgot to repeat that in this video. Thanks.
@@MichaelBellmbell556 The expensive roller pin, for the bolt carrier, like the roller pin you had that self destructed. I did not see any improvement when I was using it, and was curious if it was any better than the one you had.
Mike. Thanks for the video, really well put together and concise while staying informative. Keep it up!
Thanks!
Thanks for the review, I have had really good results with the endomag
They have worked very well for me.
Awesome review of the varieties of ammo
Thanks for watching!
Glad to see u do this video I'm very interested in this idea for magazines.
Thanks for watching!!
Thanks again......Great Video and info.....Hope everything is going well for you cause .I just noticed you haven't been around in several months.....You Can't leave us now .....We're loving your videos !!! Thanks for all that you have done.....and hope you continue to post videos.....
Thanks. It has been too hot and buggy at our range. Then had a list of "honey do" projects and other life events taking my time. Have a bunch of items in the shop to review. Thanks for the kind words. I will be back in production soon.
Thanks for the great reviews, tests, and videos. I purchased several of these after seeing your video for endomag. Got to say I haven't had and issues with them so far.
Thanks for watching!
Keep it up Bell, your videos are very informative
Thanks!
@@MichaelBellmbell556 If I were to run an 20inch barrel on a collapses butt stock, what buffer should I be using??
SPC Vong
101st 3rd, Bridgrade
For Campbell, KY
@@bravocompany2196 I have used a standard 3 oz carbine buffer with a standard carbine length spring on 20" barreled uppers with no issues. It depends on the gas port size.
@@MichaelBellmbell556 Roger that
Thanks Mike! You the man!
Thank you.
Great video Mike. Hey I went ahead and emailed you regarding helping out with the channel.
Thanks for the review!
Thanks for this!
Our Endo mag has worked great will all types of ammo, even steel cased Tula, Biggest issue I see with endo mag is premature ejector wear, I suspect 1 magazine insert is only going to be good for a couple thousand rds before needing a new Endo unit installed in it. We have 500 rds+ on ours and it still works, we will see for how much longer.
I agree. At this point durability is my only concern.
What material is the ejector made out of? Polymer?
@@TheSonsOfSimon Yes it is polymer and its not replaceable without replacing entire unit, i bet next version has it replaceable by itself.
@@TheSonsOfSimon Yes, polymer.
This is awesome! Thank you very much..I had some concerns about the quality initially and general wear and tear..how have these held up for you thus far after a few months?
They seem to be durable.
been thinking about getting these and a cmmg rdb bcg/barrel but every time i do, "just" an upper it always turns into a complete gun. I always seem to justify it some how (have extra buffer or whatever) well that's almost a complete lower, what the hell... still on the fence but leaning towards one that takes glock mags. Big Thanks for the vid Mike.
You have a diagnosis of BRD (black rifle disease). Thanks for watching!
@@MichaelBellmbell556 lol, didn't know they had a term for it, but yeah, sounds right. I tell my wife it's my 401k.
Spoiler alert: All the ammunition ran just fine.
That's the version LOL.
supposed to say "short version"
I'm a little late to the show but would you be willing to test the Fostech echo trigger with the endomags? Considering having a correct bcg to clear the trigger lock. If you don't have a correct bolt carrier group, foxtrot Mike makes one for about $100.
They fed a full auto fine so they should be fine with binary.
Thank you, sir! Keep up the good work over there!
Thanks for the very useful video Mike!
Would you or anyone else know if the Endomag insert the same as the CMMG 9 ARC insert?
According to CMMG...... "Compatible with CMMG 9mm Radial Delayed Blowback uppers only". I have not seen or handled one so I am not sure of the differences.
Yes. Endomag makes the insert for CMMGs proprietary radial bcg/barrel combo.
Did you use a heavy buffer or springs to help cycle with the suppressor better?
I used the 9mm spacer in the buffer tube with a standard carbine spring and standard carbine 3 oz buffer. I covered this in my initial Endomag video but forgot to repeat that in this video. Thanks.
Did you use the part I sent?
??
@@MichaelBellmbell556 The expensive roller pin, for the bolt carrier, like the roller pin you had that self destructed. I did not see any improvement when I was using it, and was curious if it was any better than the one you had.
Do you know of any mag loaders that work with these?
No. That would be nice. LULA does not.
Micheal. Do you have an email or forum you’re on?
Michael Bell thank you!