Video

That’s rough

Four cables in a 25mm single box . 🫣

That’s good dewalt electricians stapler works on block does it work on brick also ?

I'm waitong for RGB consumer units like RGB fans in PCs. Totally useless but look good for YT

Boy.....you tube sparkies ...board chamge needed asap....we can do that..😊 ...neat got it ....

Was that a framing nailer you used to secure the chipboard 🙏

After fitting many consumer units throughout my career I have never been so in awe of the mains unit you installed here to actually find and fit blue tie wraps on your blue rcbo flying leads blew me away. 😂😂😂

You should check the manufacturer's instructions for the permanent supply to the heaters. Some of them specify a switched fused spur / fused connection unit, so a 1363 socket isn't really suitable (although wouldn't necessarily be immediately dangerous). No problem with them hanging off the radial/ring socket final circuit, just some manufacturers want them hard wired.

Looks like working at that house is going to be a Goodyear. You must have both been very tyred after. But hopefully the video will gain some rubber. Have you now finished Dun loping all your cables.

I started as a Spark in the 90's and trust me neat fuseboards tidiness like today were not a thing, it's a FB no one sees it. Social media has this thing about showing masterpiece tidy FB's and I think Why, as long as it's not a total bird nest and it's easy to test now and the future move on.

Birth of a legend. Respect Mike to you and the team

How did this get signed off by building control? Quite a few reg breaches?

The problem you have is that they are not submersible connectors! Water will collect in the holes and seep in. We never use mains in ground light really. Not worth it. For mains voltage you really need to fill connections under ground with gel. I use similar connectors to those but always keep them of the ground!

You’ll end up with 2 hairline cracks either side all the way up if it’s on a dry lined wall (needs a scrim tape on it to prevent cracks).

Stick some sticks like shi* on the back of the board for extra strength

I can only imagine the temperature in which you are working with.😮

Hi I recently put a garden lampost light in my garden. It has three lights on it and I'm using TCP ES A60 RGB & WHITE LED SMART LIGHT BULB 9W 806LM in each. And 5 meters of White 3-Core 2.5mm² Flexible Cable. Going into a block connector then three strands of Black 2-Core 0.75mm² Flexible Cable for the light fittings. Then I have it going into a three pin plug fitted with a 3amp fuse. Is this ok or do I need to do anything else. The block connector is inside the lamp pole off the ground. Thanks

Always great to hear tradies love using our job management software!

You are not meant to remove the silicone pouch, you leave it in, says so in the instructions. Eating it would be really nasty though yeah

What shims/packers did you use under the joists? Also, did you leave a gap between the joists and the wall or secure the joists to the walls? Thanks!

How do you waterproof it if it’s covered in water - Gel?

NIce install, Mate.

Fischer has special plugs for mounting to those polystyrene insulated walls: insulation fixing FID.

What on gods green earth is that first comment 😂

Delighted with my Zappi EV charger, Mike (and your expert install of course). Cheers David

How do most of you guys still make profit, even with the downturn of the economy and ever increasing life standards

Could've gone through the software settings!! I can't get mine to connect to the app

Very useful video. Thanks for content

Any tips of why ours is still uneven

Just purchased a 4 year old new build. It has an EV charger installed using 2.5mm T&A, with a 25A MCB on the consumer unit. Charger has been capped to 25A using dip switches inside the unit. When I plug my car in, as expected it’s capped at 25A which is fast enough for me. Is this OK or should I be expecting a house fire? 😅

What size breaker did you use for the swa?

plastic dpc around the joist will speed up the rotting process .it should be reomoved and pointed up with nhl 3,5 so it can breath ,breathability is key .air vents air flow .

Not to many obviously's lol I was starting to think I was watching a seamstress at first, there is more "so"ing in this than on a seamstress's video lol oj

Pretty sure regs state you dont have to earth the back box with a metal frontplate with a fixed lug. Just have to earth the frontplate. Obviously its good practice

Change your supplier he obviously doesn't give a toss about wasting your time dump them their are loads of suppliers in the community that will have your business. Go on name and shame them.

Metal fronted skt. behind something...you cant lose it...if you ever need to replace a faulty one , on show ...and range is no longer available ...//

So how would you do the earth lead if you were to install these same metal sockets into dry lining back box a plastic back box 😂😂😂😂😂😂😂

I thought for sure when the music started, I was going to hear you bust out with a rap. 🤣🤣🤣 Good video. The voice overs added to the texture of the production. Good job mate.

No such thing as an easy, a job is only hard when we have no or few solutions or some idiot makes it hard

Sorry but why do you conform to wiring your lighting feeds to your switches where you end up with multiple connectors in your light switches which is ridiculous, as a recently retired sparks who worked in the industry for 50 years I only beleive in change when that change is warranted and sorry that change is stupid, sparks excuse is o what if the homeowner wants these modern switchless lighting you need a neutral there well sorry to put you straight you don't need a neutral there because you can buy ones that don't require a neutral, I had it hammered into me from a young age that you make sure that you keep connections in circuits to a bare minimum because I know modern sparks don't use this phrase but it's called good electrical practice, you see I spent most of my career as an Industrial electrician working with electrical clerk of works checking every inch of my installation which meant that everything had to be correct whereas you lads only inspect yourself, not saying that you don't do a good job because having watched your blogs it's obvious that you do a good job , what irritates me the most is these electrician bloggers slagging off ringmains in my opinion because they are basically lazy and only want to wire radials , anyway keep up the good work , but feeds to the light fittings

Why use mains voltage lights? Why not extra low voltage? Far better for the situation and safer. Also the only join that will never fail within the ground is a resin join really.

Had similar issues with Saxby walkovers within 6m of installation. Swapped the fittings for Collingwood and they've been completely trouble free for almost 11yrs. Wouldn't fit any other brand outdoors ever now

I hope you've still charged them for a day even if it has been a year or so. 3 - 6 months guarantee is adequate

Plastic grass, tiled patio, water can’t naturally drain away! No wonder they are wet.

You have followed the manufacturer's instructions?

I still don't understand why manufacturers make these 240v, if the fitting had been MR16 and 12v most of these issues would be easily and CHEAPLY fixable. And would not trib your breaker.

How would that explain the water in the light fitting. Would you not consider that the water is running past the light fitting running down the cable and into the joint only a suggestion. Could you jot run a bead of silicone round the light fitting before fitting it into its hole. Fyi LAP at screwfix have a 3 year warranty. Lol.

I have those connectors on my pond pump. The conical grip is against the gland nut.

Was the patio jet washed? The pressure is usually enough to blow the seals and drive water into these kind of lights.