Video

Trying to find bearing cups on aliexpress, anyone know the search terms?

This video helped today. I had to feel the clearance. Adjusting shoes away from drum helped this.

dude you can make 4 holes in plastics and screw lcd to stand ...

Painful intense process ! Better off purchasing a new Keyboard... Used keyboards are high risk as seen in your case..... Thank You for the time you took to make this video...

If I build a battery with ten Samsung 30Q cells, how many amp hours will it have?

Hellow. Here we refill the cans. But it dont work in the new campstove, here in belgium we have only propane ore butane. If we we fill with butane are the problems solved? Thx

The Bike Sauce built a pretty simple little bearing press which seems easy enough to use to do this. The video was called "Replace Sealed Cartridge Hub Bearings" or something similar.

My Yamaha receiver power button won’t even toggle - it’s frozen/stuck. It doesn’t turn on via remote control either. Could it be the same problem?

Think of buying this model because of the simplicity. What do you think?

You are the master there is no way I could do this. lenovo are the stup1dest laptops ever. my lenovo ideapad 310 turns on after pressing the power button a million times, and the screen goes and comes at will. it shows the screen when I direct flash light to it

Amazing! Thanks for sharing. This brought my Bosch Classixx 6 1200 Express back to life. All just for a few GBP. 🎉

Use wide washer to evenly torque in the bearing

Thank you l I’ve been interested in learning how to fix it

This a fake video 1 my A do you know how much a 3d printer would coast just to to do this?

This was perfectly watchable! 😄 Nice fix. These seem to fail here around on super hot days or during storms. I always try to keep a spare these days. Worth its weight! Heck of a deal getting that for 8$ with an easy fix. 👍

Hi i did this and now my laptop is turning on but the problem is its not charging i tried to remove the battery and plug in the charger but its not turning on , but when i put the battery back it turns on normaly its says charging but its not charging there is an orange indicator light that say charging but its not any solution ? I reckon it has problem in charging circuit somewhere

Bro 💀 not the motor alone

thanks for sharing

Sweet upgrade! I bet the wheel rolls super smooth!

How did you transfer your operating systems?

Dang man that is way beyond my pay grade so if I break something I will have to send it out

Hi, I subscribed because I appreciate the video and the playlists. I am in the same sector of Energy Home DIY but in Europe and under 1000 subscribers yet. I would have expected more comments on this useful video. I will try to contact you.

I just bought a unit on AE Just like this one. Its totally useless. Wont weld anything. Chinese junk. Total failure. Its a 230V by the way.

Not mentioned in the video, prices are in AUD$. This was back in March, prices have since come down significantly and I see some used Macbook's about the same price (or cheaper depending on condition) as I spent fixing this one. Check the link in the description. Also the method where I installed the OS via USB could have been avoided by connecting it to another Mac in DFU mode just like and iPad or iPhone.

I know its an old video but there are many vids of these sunkomachines. It appears that the 110v are the most problematic. A simple rewire of the transformer secondary winding will cure the problem . Rewind it with same gauge wire but get as many turns as possible , two three . I havea 240 v model worked on very thin nick3l strip but not so good on the thicker stuff. I rewired it by adding more wire to the supplied winding .vids show how its done . Works verh well now on 60% . Only way to undo welds is tear the metal or grind it off. Have a go it took me a couple of hours and was well worth tge effort.

It is amazing to me to see these things repaired , full watch and always here to support you

wich filament did you use??? not a 100% sure on the plastic stuff better turning some wood or some rubber!!!

Ozito short for Ozi Tools (Aussie Tools)

Bro Yamaha AVC 30 Treble pot has snapped. I cannot use Treble. It looks full of silver metal? like alluminium. The other knobs are long Black plastic stems and work fine. If i can get into the hole and undo the nut can i then replace the pin?

We have a front loader and haveto leave the door open and put vinegar in it to keep it from mildew smell, Subscribed thank you

Can these things work for dynamic microphones?

One of the big problems in UK winters is that the propane evaporates first leaving, at half weight, mainly butane which doesn't evaporate quickly enough to give a significant flame. I figure if I refill at that point back to just below the original weight it should allow more of the contents to be used without exceeding the original pressure significantly. Probably the next refill should be back to 3/4 weight, then 1/2 weight. That canister can then be saved for summer use.

A THOUSAND thanks for showing how to replace the blasted silicone buttons! It looks much easier than I thought it would be. Otherwise the keyboard is worthless. Cleaned the well where the key sits with alcohol and a brush and the top of button just flew off. Undoubtedly fatigued from being pressed a zillion times in its 13 years of life and use. UGH. Now to find a replacement button from a donor keyboard somewhere... Are the buttons the same on A1315 and A1255 keyboards (different buttons for larger keys of course but for the main keys)?? THANKS!!!!!

how is the delay on the screen ? I have the HAYEAR 5030 and it is very noticeable :(

Saan ka bumili ng spacer ng axle ng hub?

How about night??

This is very useful for repair, thanks

kindly tell me the solution i have yamaha Rx v861 Master audio with HDMI when i play dvd player with HDMI suddenly avr off avr not on till now

You need to earth your houses roof.

Nice work! I keep putting off getting one of those desoldering stations but they seem really handy.

Everyone starts with flanges already in place. I have the same situation as you and need to add flanges. Thanks for this.

Life saver, just googled thermostat location cox I was about to do water pump and thermostat, and your vid popped up, I was gonna fo the other 2 things but it never explained the AC issue... this does... awesome cheers bud

Currently trying to research these keyboards a bit more as I’m looking to repair more difficult issues and I did not expect to see part of my listing at 3:10 haha - Very interesting video thank you

Thx just reached the same conclusion with my VQ, your video good confirmation

wow that's way off.. surely the soldering iron is at least 200C :( I'm disappointed I hoped it would be more competent

Great video! No bs, directly to the point, with every information you need to solve this and similar faults.

Oh, yes. Over here, in North America, we have the Whirlpool family of washers with a certain undervalue capacitor on various boards. Replace it and your gold. A few dollars for parts as opposed to hundreds for the board. Now, one can not say with certainty that it was designed to fail...just, I've never repaired a board from direct drive machines which had any other fault....

If it were me, I would also tested the capacitors to make sure they were still in spec, since they might have experienced unusual load.

Who is Noah Vale and why would anyone try adjusting to him?