Video

4:09- I was about to be shocked if you just cranked the gland nut off, Lol.

Waste of my fucking time. Thanks! 🖕

One step not covered is to place a new gasket on the pump before installation. It was clearly installed in the video, just not mentioned. Most new pumps come with them anyways, so it should be fairly obvious. The rubber OEM style gaskets are generally a little better than the metal ones if you can find a pump with one included. I used to be a ford tech and did these all the time. Much easier than the insane internal timing chain driven ones on some newer vehicles. You can get away with only disconnecting the lower hose, but it's easier with both off for sure. Great video.

Yeah I have used one like it

Both are good tractors but the JOHN DEERE 4430 is way better than the international 1066.

4430 becuase of the soundguard. Love those cabs

John Deere all the way

I have a 2012 to do.T his video should help a lot. Thanks

Hi! How many miles per gallon does it get on gas?

Did you have to set it on top Dead center if so where are the timing marks

4430

excellent very hepful info for beginers thank you

1066 black stripe all day

I can't name a better tractor the 1066 black stripe is badass

My new shaft seal is as hard as a rock. I have that seal tool, but there's no way it's going to bend. My bobcat seals were pliable like that though.

Exactly what I needed to see except the new rod seal I have is as hard as a rock with zero flex. Hmmm... dang.

1066 my all time number one favorite tractor of all 🇺🇸🇺🇸

Jd 4020 or 4430 but that 66 is still a beast

4440

If you take the accessories it should give some room

I'm definitely going out the top with out pulling the transmition.

You need to show folks how, where and how much oil to put in the injection pump. Looks like that part got skipped....

1066 definitely

Soooo satisfying

The zip tie on the belt, took less than 10 min to change the water pump belt. :-) Thank you.

That was really helpful. I have a friend with the same problem. Thank you very much for that

1066 IH forever

Great Video for the guys who have never had any experience with them, I've done a few too many.

Thank You!

any john deere

Nice piece of equipment there

Keep up the good work

Im still picking up by hand 1 at a time it's not hard just do it

4430

1466

Bro didn't have to flex on us that hard.

Yo the soybean game is fucked up, feel bad for those farmers

Willing to part away with your old engine

Watching this video saved us. Thank you

What a good job producing this video!!! I appreciate you.

I have a cylinder style that I can't find a video on. Basically I take the top off but the gland stays. There's just a thin cap on it. I can't get any further. Anyone know anything about these?

Thanks! Super easy!!! Did have to use 1/4” drive on that rear bottom bolt. Throttle linkage in the way! But the Ziptie on the belt!!!!!!!!!!!!!!! Heck yes!!!! I’ve been turning wrenches for years (hobby only)!!!

Awesome video!!!!!! Thanks!!!! Timed it…. Took me 42 minutes but…. Top hose clap wouldn’t open properly…. Then dropped extension between radiator and bumper!!!! PS, didn’t drain radiator… just lost maybe a quart when pulling off hoses! & the zip tie on the belt….. saves so much time!

I'm doing a rebuild in my 684 and tore the cylinders apart. Where did the little check ball come from?

ih 464 D179 here and finding the rocker specs had oddly been a challenge so thank you

Well I can name bigger and better but that's one of then

Great video

Good to see IH tractors still working

Definitely the 1066 IH

Were you homeschooled? I’ve never heard such poor English.