Video

Well explained waiting for more videos on adjusting valve.thank you.

any hep with the part on the frame at the bottom of the steering shaft that 90's to the front?

Dude... Thank you very much for this video! It was exactly the solution I was looking for!

That was the best how to video I've ever seen.

Just got a predator vertical engine for a yard trimmer. It’s a lawn mower version of a string trimmer. I will implement a ground extension to switch to console identical to how you demonstrated. Thank you for sharing your videos. Best.

Thank you.

Many thanks roll one of little diggers over and it lock had pull injectors out watch this went back out got the job done back up and running 👍👍👍

Looking for a gearbox place to full up whith oil

Thx! Gotta break mine down tomorrow

I'd like to see a video about disabling or removing the flywheel brake.

I had no idea there was ground connected to the engine brake.

Did you have to adapt to the longer shaft of the predator engine vs what you had initially? I replaced the Kohler XT775 engine on my pressure washer and the shaft was about 1.25" longer, so I had to use spacers between the pump and engine.

Is this a mirror image? The alternator is on the driver's side on a Chevy pu truck.

Yep, after 10 years, people still find your video helpful. It freakin' worked!! Thanks!!!

Why can’t u just tap a thread??

i have a problem in my lcd cable for this computer, do you have an video about accessing it?

I wish you would have recorded the engine running before diagnostics and replacing it. I have an 05 passat 1.8l it has a really rough idle, when i start it up it blows blueish white smoke (assming its the engine adding too much gas)

Nice tidy job

Do you know the make of that 60” deck?

What is the back pressure line exactly?

So i have a 04 passat 1.8t i have changed the maf, new coils and spark plugs, both o2 sensers i drop from 13 codes to 3 codes and has rough idol when starts like at 700 800 bounces flashing cel and then if i drive no power really i need help do u think if i change this it will fix my problem? Srry if i misspelled anything not grate speller oh and its just missfire on 1 thats it

this video was great for helping me rebuild my pcv system the previous owner damaged

Beneath that mock pulley is a boss to put a grooved pulley to bypass the AC, or for those that do not have AC.. trying to find a video on that setup as I just bought that bracket to swap my older truck to serpentine and it did not come with the bolt or pulley there.. I found the grooved pulley just need to see if there is some special bolt or something behind pulley, etc.. I see images of using that boss, but no details or parts list.

I just bought a Kioti LB1914. Your videos are very informative, Do you plan to do any more on the Kioti?

Great video Sir. Thank you. I have a similar setup. I also have the Mock Pulley instead of an AC compressor. By any chance have you played with the possibilities of a smaller belt going directly to the Power steering ??

Anyone know what shade of blue the frame is? Im looking for a rattle can to paint mines.

This has been me to, as of current date...I dont think they have made changes to these jugs yet. Still crap and costly losing coolant, putting people at risk over heating, not to mention breaking down. Basically a road hazard if you can not get pulled over because car is blocked in 6 lanes of traffic.

No motor 4 cilindros é a mesma forma de manutenção? Eu tenho um V1505-TE

Just went through this with my Suburban when trying to rewire a trailer plug. There is a separate pigtail taped off inside the rear left side lighting harness that you can use for either purpose. The one 10ga wire within that pigtail is the 3rd brake light wire. C/K and Suburban Tahoe had generic wiring harnesses, if you have the tow package it will be there on any OBS truck. The ideal setup would be to use the pigtail for your camper top, and use a Curt or Hopkins T connector for the actual trailer harness if you are running both at the same time. That's about the cleanest way to go, and the location of that pigtail is set so that you can run it up inside the left rear corner of your bed.

Great video

I have a Mini 325 that the primer bulb keeps sucking itself dry. Same issue you think?

Question. Did I ever set the valves on this baby ? I just bought one and I have been looking for the timing window all day. Can’t find it. I seen somewhere that the valves set is 0.15mm

Very encouraging. I've got three cylinders to weld fittings to, the originals having rusted away. I was worried about the quality of my welds but not so much now. 😂 Thanks again!

Will the Pvc valve cause my diesel engine to blow white smoke and burn alot of oil?

Promo*SM

На який тиск вприскування форсунок ви налаштовували?

I can’t tell you how much this was helpful, thank you!

thanks this just happened to my bobcat cylinder. New to this. how easy is it to take off the cylinder so I can take to a local welding shop to fix\?? Anything I should be aware of when I remove and put back on the fixed cylinder? thanks!

Its really hard to find videos about Kioti LB1914 Thank you so much for your videos. Could you please make one videos showing how to check the fluids and please tell me where the Hydraulic, and transmission fluids go? This Information will be much appreciated. Thank you!

I wonder what a 'nozzle holder' is and why it has different torque as a 'holder' versus an 'assembly.'

Great Video! How did you clean that old grease?

Muy bien excelente video 👌

That’s the great thing about old mechanical diesels. They can sit for years and all they need is a good battery to start . No check engine light and no computer to put it in derated limp mode.

my 05 vw passat with the v6 engine started misfireing and had a coil code so i replaced the coil, plugs and wires and now when i turn it on it has a rough idle and if i dont keep it above 2k rpms it will go to like 400rpms then die. while working on the coils i snapped the crankcase breather hose and i noticed it was plugged of old oil so im wondering if my pcv and this hose is the cause of the rough/inability to idle

Great video, well explained! Thanks! I own an old compact Antonio Carraro Tigre model. I had a runaway with it but luckily the engine haven’t seized. I was able to start it again after servicing it but the engine runs rough and clunks much more. It also make a bit of smoke. Not much and white, but it does. what I've read is that injectors might be the cause of it. So, I was wondering what was the cause on your Kubota that made you clean your injectors? Thanks!

So did it run after? I have 3 of the little junkers 2 run 1 won't run for nothing I swapped out everything but the injectors but it ran all night one time and never fired again. I don't get it. I don't see injectors going bad just like that. It did sit 5 years before the 1 time it ran so idk maybe. Thanks

My fitting need replaced, you wouldn't be close to Ohio are you?

Working on a Vermeer 450 TX mini skid with this motor injectors are leaking on top, what could possible issue be?

When labeling injectors, isn't #1 cylinder on the waterpump end?

Had to laugh when you found the clutch safety switch. Reminded me of my 87 Isuzu Trooper II with manual trans, had to push in the clutch to start. Those Koreans!