Cheyenne that was a great video. I've had my kit for almost 2 years and decided to jump on installing it this morning. Your video was a big help. The ol 300 can stop without running into a pond now ! Lol
I just installed this kit on a 1991. The instructions said to mount the calipers behind the axle but I found that I couldn't route the brake lines (they weren't long enough). So I ended up mounting them on the front and found that the stock brake line route didn't have to be altered at all
Didn’t know that someone full of information and mechanical Experience also looks very pretty LOL you got it all good luck with everything like watching your videos very informative and entertaining
I've been riding mine without brakes but where we are is very hilly. It's a pain to have to roll off a path to stop on the down hill sections. I think I'm going to give this conversion a try.
U sure that’s not mine. Lol. The no brakes or sticking brake. Love video’s Getting kit for mine since I got 12” wheels mine we’ll have brakes on front. Sweet 300. Keep those video’s rolling and the gas ⛽️ flowing. From ur WV hillbilly buddy stay safe
I have a quick question.....I bought the same kit from super ATV n they didn't have directions n I put them on the back side n I see urs are on the front...dose it matter what side they are on I just wanna make sure I got em facing the right way.....ya know what I mean???
Hey! Instructions are online. It will work either way. I have mine in the front do debris isn’t forced into the caliper as bad as if it was on the back side
Is it working well with the calipers installed in the front of the rotors? I'm about to receive this kit, and it says they're supposed to be in the rear of the rotors 😟 Every video I see, it is either or! Nice video & good install!
Typically in vehicle applications the calipers are installed in the rear, so if they could go that way I would, but if it's working I'd leave it until I might have to rebuild the front end, then with everything dissembled I'd go the other way
Love your videos and has helped me out, so thank you! Question, I just got a 95 Honda 300 fourtrx and I’ve noticed “gravel sounds” mostly when I turn either way. But, I can hear it as well just going forward just not as pronounced. What’s the 1st thing you think I should look at or do? Any help would be appreciated, thank you! Shanon Thompson
Thank you! I love to hear the videos are helping people. If the noise only occurs while turning I would suspect the axles, front wheel bearings, possibly tie rods as well.
I just pulled my father-in-laws 97 fourtrax out of the weeds this past weekend. I need another project like I need a hole in my head< but I got it to fire up using ether and the kick starter and now I want to restore it. It has good compression, but it needs a ton of work and parts. I've watched your other videos adding the floorboards and rancher shocks. Do you have any other mods planned? I would like to get it running again for him to ride around the farm. I'm located in central NC too.
Nice! And yes I do I’m debating on the snorkel or not. I’ve been trying to swap the plastics for blue or red but I have not had any luck finding a good set. Are there any mods in particular you are looking at?
@@CheyenneBullard Just bought mine & I'm trying to find the FRAME number ( not the decal ) per the manual but can't, I DID find the engine number, if you have time on your next video can you show folks where the engine & frame number is??? BTW, are they supposed to be the same?? Thanks
Can you please confirm the link to purchase the kit. I have a 1998 Fourtrax 300 FW 4x4. Link in Amazon says for 450 Foreman and it says it won’t fit. Thanks.
Cheyenne that was a great video. I've had my kit for almost 2 years and decided to jump on installing it this morning. Your video was a big help. The ol 300 can stop without running into a pond now ! Lol
Lol 😂 thank you! Glad the video was helpful!
I just installed this kit on a 1991. The instructions said to mount the calipers behind the axle but I found that I couldn't route the brake lines (they weren't long enough). So I ended up mounting them on the front and found that the stock brake line route didn't have to be altered at all
Excellent presentation and explanation of the kit and steps from the beginning to the end.
Thank you!
Thanks Cheyenne you have a great instructional style, very easy to follow keep it up.
Thank you!
Didn’t know that someone full of information and mechanical Experience also looks very pretty LOL you got it all good luck with everything like watching your videos very informative and entertaining
Haha thank you!
@@CheyenneBullard ur so welcome !!!
Keep up the great attitude and confidence in ur videos 👍👍👍👍
@@nabielsuleiman7039 thank you! 🤙🏽
I've gotten so used to not having breaks on my 300. I ride it through town and just shift down
That’s what I used to do but these are so convenient to have.
Damn straight figured I was the only one lol
I've been riding mine without brakes but where we are is very hilly. It's a pain to have to roll off a path to stop on the down hill sections. I think I'm going to give this conversion a try.
Perfect video. Understandable. But one question. What size wheels should go after this job ? Because original small wheels will not fit
The kit says a minimum of 12” wheels or larger and that the oems will not work
Also thank you!
@@CheyenneBullard thanks. How cost this conversion kit? eBay 700eu. But that's touch
Support
All the way from India
Yessir!! Thank you 🙏🏽 hope you are doing well
When reinstalling your brake line, you didn't have a crush washer on both sides of the brake line fitting. Watch out for a leak.
Thanks for the tip
It nice to so woman fixing there Atv good job
Great job its nice to have them!! My old 350 rancher brakes were gear down fast and turn wheels 😅😂
Thats how this was was! but not now!!
U sure that’s not mine. Lol. The no brakes or sticking brake. Love video’s
Getting kit for mine since I got 12” wheels mine we’ll have brakes on front.
Sweet 300. Keep those video’s rolling and the gas ⛽️ flowing. From ur WV hillbilly buddy stay safe
Class presentation...mike Scotland
You go girl! You be doing the damn thing!!👍🤙
Thank you! 😄
Your freakin awesome!!
Thank you 🙏🏽
Both my front and back are screwed should I do this on the front or worry more about the bavk?
You can do this on the front and be pretty happy. Most Honda 300 brakes don’t even work tbh. These worked great
Do you have a pic of how the lines run on the control arm ? Thanks
Did you have any issues with the lug bolts backing out when you tightened up the lugs?
No sir
Just ordered this yesterday. I just wanna make sure I saw the video right, you used the brake drum to beat the studs out of the hub right?
Yes
Thanks so much!! I need to do this
You’re welcome! Well worth it
Can I use my 12 inch rims or do I have to go 14 inch rims?
Most 12” wheels you can. Depends on the offset of them
I have a quick question.....I bought the same kit from super ATV n they didn't have directions n I put them on the back side n I see urs are on the front...dose it matter what side they are on I just wanna make sure I got em facing the right way.....ya know what I mean???
Hey! Instructions are online. It will work either way. I have mine in the front do debris isn’t forced into the caliper as bad as if it was on the back side
@@CheyenneBullard ok thanks n so u think it's better to put them on the front then cuz if so I'll switch em tomar real fast...n thanks again!!
@@shanewilliams6772 you’re welcome!
Dream girl. Awesome job!!
When are you going to open your shop. You’re doing a great job !!!
😂 I just tinker on things and try to show others but thank you!
@@CheyenneBullard well you do a great job and you have so much confidence, something to thing about in the future . Keep up the good work !!
@@dangson1183 thank you so much!🙏🏽
Is it working well with the calipers installed in the front of the rotors? I'm about to receive this kit, and it says they're supposed to be in the rear of the rotors 😟 Every video I see, it is either or! Nice video & good install!
Yes it is working well!!
Typically in vehicle applications the calipers are installed in the rear, so if they could go that way I would, but if it's working I'd leave it until I might have to rebuild the front end, then with everything dissembled I'd go the other way
Love your videos and has helped me out, so thank you! Question, I just got a 95 Honda 300 fourtrx and I’ve noticed “gravel sounds” mostly when I turn either way. But, I can hear it as well just going forward just not as pronounced. What’s the 1st thing you think I should look at or do? Any help would be appreciated, thank you!
Shanon Thompson
Thank you! I love to hear the videos are helping people. If the noise only occurs while turning I would suspect the axles, front wheel bearings, possibly tie rods as well.
Thank you so much for replying to me!! Also, do you have a part preference for those that you mentioned? Do you use Amazon? I can’t thank you enough!!
@@jake06062000 yeah I actually have an axle video of the 300 on my channel. The link is in the description on that video
Will it work for a 1995? I looked it up and it said 1996 up?
Awesome job!
Thank you!
Hey could you do a snorkel video on the 300 please?
Ask and you shall receive!! 💪🏽
@@CheyenneBullard thank you so much
So overall is it a pretty good quality kit? And how’s the stopping power?
Definitely a well built kit and easy to install. Works great!!! Every Honda owner needs to get this kit!
Job well done.
Thank you!
I just pulled my father-in-laws 97 fourtrax out of the weeds this past weekend. I need another project like I need a hole in my head< but I got it to fire up using ether and the kick starter and now I want to restore it. It has good compression, but it needs a ton of work and parts. I've watched your other videos adding the floorboards and rancher shocks. Do you have any other mods planned? I would like to get it running again for him to ride around the farm. I'm located in central NC too.
Nice! And yes I do I’m debating on the snorkel or not. I’ve been trying to swap the plastics for blue or red but I have not had any luck finding a good set. Are there any mods in particular you are looking at?
Are you planning on doing the rear like this also ?? I found the SuperATV Utility ATV Rear Disc Brake Conversion Kit for Honda 2x4 & 4x4 online also
I wish but those kits don’t fit the Honda 300 they fit the ones with the brake drums that are right beside the hub
@@CheyenneBullard Thanks for your info, JUST bought one and trying to familiar myself to them, that's how I found you !
@@REVNUMANEWBERN you’re welcome!! The Honda 300s are an awesome classic!
@@CheyenneBullard Just bought mine & I'm trying to find the FRAME number ( not the decal ) per the manual but can't, I DID find the engine number, if you have time on your next video can you show folks where the engine & frame number is??? BTW, are they supposed to be the same?? Thanks
@@REVNUMANEWBERN the frame number on these are at the front on the horizontal metal bar you’ll see it stamped in there
What kind of tires do you have?
28” Maxxis zillas skinny wife setup on 14” wheels
What rims are those on that 300
Some 14” sti wheels
How long did this brake job take you to do?
Less than an hour! definitely worth it
Can you please confirm the link to purchase the kit. I have a 1998 Fourtrax 300 FW 4x4. Link in Amazon says for 450 Foreman and it says it won’t fit. Thanks.
amzn.to/2SskG9j
Should be the same kit And you’re welcome
I just subscribed to hear you say um. Jk, I have a 300 also
They are super fun little tanks
All I seen is foreman, rancher, rubicon is it one of those
Does anyone know if these will work on 2wd
Unfortunately no. SuperATV quit selling the ones that fit the 2wd models
@@CheyenneBullard awesome thank you
@@EricCarter99 you’re welcome !
Can I use this kit for my 2x4?
Unfortunately no. SuperATV quit making the brackets for the 2wd machines
Is it possible to find the brackets?
@@liftedresearchhhh7865 probably can find used ones