Budget D16 Turbo Honda Civic EJ8 | Boost Gauge | Wastegate Spring | Spark Plugs | + POV Drive

Sdílet
Vložit
  • čas přidán 22. 09. 2022
  • Finally we were able to take the car around the block and hit wide open throttle on the Boosted D16Y8. Swapped out the wastegate spring for a 4psi spring. I also forgot and had to regap the plugs…😄
    Website: cjbuiltperformance.square.site/
    Instagram: @CJ.Built
  • Auta a dopravní prostředky

Komentáře • 24

  • @peterbryant3584
    @peterbryant3584 Před 2 měsíci

    Ok pretty good video that thing is clean bro

  • @aaronfraser2347
    @aaronfraser2347 Před 5 měsíci

    That spark plug cleaner is mint

    • @CJBuilt
      @CJBuilt  Před 5 měsíci +1

      Comes in super clutch sometimes 👍🏻

  • @oompaloompaheadass4405
    @oompaloompaheadass4405 Před rokem +2

    5:11 typical honda moment😂

    • @CJBuilt
      @CJBuilt  Před rokem +2

      😂😂 always have the laptop on deck
      Except When my girl rides along, she becomes a tuner at that moment 😂

    • @oompaloompaheadass4405
      @oompaloompaheadass4405 Před rokem

      @@CJBuilt forreal dude😂 whenever my girl is in the car she gets to hold the laptop no matter what

    • @CJBuilt
      @CJBuilt  Před rokem

      Ahah I feel that. She loves holding the laptop🤣 although she does love when I’m tuning and she’s driving as well

  • @infinitex1732
    @infinitex1732 Před rokem

    If you don't mind how much did going turbo run you? Mainly for the turbo, intercooler, oil lines, BOV and wastegate

    • @CJBuilt
      @CJBuilt  Před rokem

      Yo what’s up!!!
      Message me on Instagram and I got you!
      @CJ.Built

  • @shawn6684
    @shawn6684 Před 2 měsíci

    I just started getting back into building another but turbo this , i have 96 y8 but i cant remember what ecu i need if im going turbo for tuning ? Any help would be appreciated sir .

    • @CJBuilt
      @CJBuilt  Před 2 měsíci +1

      Hey how’s it going!
      You will need to go OBD1, since it is a Y8 you’ll need a vtec ecu.
      P28 is a popular one that’s a go to for a VTEC ecu.
      You’ll just need a jumper harness to convert the obd2 plugs to the obd1.
      Any questions let me know!

    • @shawn6684
      @shawn6684 Před měsícem

      @CJBuilt thank you much sir !

  • @Trakyakizani
    @Trakyakizani Před 4 měsíci

    What should be the healthy pressure for the original engine?

    • @CJBuilt
      @CJBuilt  Před 4 měsíci +1

      You mean as in boost pressure?
      To be safe, on a turbo this size I would stay around 7psi.
      You can shoot for 10PSI but that does begin pushing the limits depending on how you drive it and how the tune is.
      7-8PSI is a fair middle ground of fun and safety.
      On a smaller turbo you can probably get to 10PSI without an issue.
      PSI is not the concern, it is the power the car outputs.
      Bigger turbo = more hp per PSI
      Smaller turbo = less hp per PSI
      Hope this helps!

  • @eduardoornelas6736
    @eduardoornelas6736 Před rokem

    from where do you get the boost spring

  • @CypronieNelson
    @CypronieNelson Před 8 dny

    Is that a Gt28 turbo or to4e turbo

  • @richardmontalvo3513
    @richardmontalvo3513 Před 4 měsíci

    Man I need a manifold a/c friendly 😢

    • @CJBuilt
      @CJBuilt  Před 4 měsíci

      They sell some that are A/C friendly, just may need to notch the block a little or route the turbo in the reverse way than I did. I tuned a car not too long ago with an A/C turbo manifold

    • @richardmontalvo3513
      @richardmontalvo3513 Před 4 měsíci

      @@CJBuilt been looking but No luck so far 😣😣 I message you on insta too

    • @CJBuilt
      @CJBuilt  Před 4 měsíci

      @@richardmontalvo3513 You messaged me recently?
      Message me again! We can see what we can find