True old school mechanics made a roadside gasket from the side of a cigarette (or cereal) packet. I've done it in the past, many times, and they lasted longer than brought ones. Good old days!, contact points, condensers, distributer caps, carburettors, fan belts, all repairable at the side of the road with a very basic tool kit. (and a great sense of achievement!) No laptop needed....Just knowledge! Who else misses those days?
@@c0nstantin86take it off. Eliminates the unbalance. Ans as long as you are moving, the air flow will cool the radiator. Just remember to install the belt.
Contact cement and a silk thread is still used on piston aircraft engines as an oil pan gasket, only you dont cut the thread and piecemeal it around the inside of the bolt hole, you run it full length along the outer perimeter and loop it back on the inner perimeter, which seals both sides of the bolt holes.
@ricos4700 No matter how precision ground 2 surfaces are, they still need some sort of sealing material. Using a silk thread simply shows how precision ground the surfaces are.
@michaelwooda9444 me too until dad brought home some surplus red RTV from McDonnell Douglas Aerospace where he used to work sealing everything from airliners to space capsules.
Right, but he did all the locktite and string thing and still just ended up using the fuckin gasket so my question is why do any of it if you’re just going to use the thing intended to do that job
The only pressure on that gasket is crankcase pressure from ring blow by, and it never even becomes 1 psi as the positive crankcase vent is connected to the intake system and engine vacuum sucks out any crankcase fumes.
@@robertragsdale6955it absolutely will not on the small block chevy he is working on. Even with 10 to 1 compression and a cam and headers there wouldn't be 1 psi crank case pressure unless there was engine damage. A later model vehicle with a factory turbocharger or supercharger could definitely have over 1 psi of crankcase pressure but not a naturally aspirated engine unless the emissions system is designed to work in a way that causes it.
Ive worked all over and the best bush mechanics come from Vietnam. Weld cranks back together, make crank bearing out of bamboo, walk miles down the road picking up pieces of engines, put back in place and keep going.
50 Million small block chevy engines were manufactured without one drop of any type of gasket adhesive or silicone and the oil pressure sending unit was more likely to begin leaking than any of the gaskets.
How were they sealed. I'll guess- with very accurate machined surfaces and accurate torque tightening. Otherwise those engines would have needed something between the surfaces as pressure builds up.
Yes Yes Yes Yes Yes Yes, people make so much shit out of nothing. He's working on it in his shop or where ever. I'll guarantee there a gasket in that overhaul kit.
This is pretty funny because as someone who has worked on scores of SBCs this could not be further from the truth. As a matter of fact, I've had several Camaros and Firebirds and the most rust free areas of the chassis is consistently the firewall behind the engine and transmission tunnels because they profusely leak oil as they age which is blown by the fans into these areas creating a protective layer of grease. First, they are absolutely required to use gasket maker on every single SBC. The oil pan gaskets and the intake manifold gaskets are a multipiece design which MUST have sealant applied. These gaskets are still so prone to leaking the aftermarket has made some one piece gaskets. Assembly instructions for new engines from GM also requires gasket maker around the water ports in all but the newest Vortec engines which were get this, prone to leaking water at the intake manifold water ports! Even GM realized their multipiece rear main seal was a bad idea prone to leaks and replaced it with a redesigned block to incorporate a 1 piece seal back in the 80's. Valve cover gaskets leaked basically all the time. There were grocery stores that literally stocked SBC valve cover gaskets in their convenience aisle back in the day because this was so common. The valve cover gasket sealing surface was not even machined, just a rough cast iron surface up till the mid 80s or so. Being that the valve covers were literally stamped sheet metal you also couldn't over torque them to try and make the gasket conform to the rough surface because then they would bend and leak 100%. On that note the timing chain cover and oil pan were also just sheet metal and would also leak if you did not take the utmost care when torqueing them down. Even then they were again prone to leaking over time. I had good luck keeping them sealed up but they were basically glued together with RTV literally used everywhere.
My buddy had a fuel pump on a international scout go bad that he has owned for 20 years. He took it apart to see what the failure was and compare it to the new one. When he opened it up there was a moon pie box cut out and used for the seal.
I’ve installed hundreds of those fuel pumps in the final build department at lycoming engines. Using the tread with the gasket doesn’t make sense. The case halves are assembled with a thread seal and that’s it. Wasting time to make it look cool for the videos is the only reason for this.
Im not sure this is showing anything worthy of a video. This is showing someone doing unnecessary things to probably and old 350 converted from mechanical to electric lift pump. Slap some grey silicone on clean surface, go take a dump, smoke cig, drink coffee or beer, allowing silicone to tack up and install fasteners with torque wrench. Loctite though?? What is the point of the red Loctite?? Not only is that shit expensive, they make silicone for this application, maybe he no get the memo.
Silicone sucks for oil bathed surfaces you went to seal. Try some form a gasket or case sealant… St least some right stuff from permatex…. Not silicone gasket maker 🤦🏼♂️
@GR40RCapri I 100% agree with you that if you do not have a properly cleaned oil free surface to start with then that silicone will not work and just make mess. If surface is completely cleaned and void of contaminants and you let it tack up properly before torquing bolts. It will certainly work,, but, whenever possible I would certainly rather use a gasket. That's a no Brainer. I was just commenting on him using Loctite which I know is just ignant!
Year I'd love to hear. Especially about the string and putting it on then taking it back off just so you can then put it together with the proper gasket. Makes no sense
The silk thread is great! So are the flexible sealants. I grease those stupid paper gaskets so they don't form the bond from hell when I disassemble. I am a little curious how calibrated your screwdriver torque method is. I doubt you got a proper stretch on the bolt to keep it secure.
That's a downgrade to me. I have a Gen V 366 tall deck with no place for a mechanical fuel pump that I don't like. I picked up a Gen VI that has a place for a mechanical fuel pump but it had a cracked cylinder so I set it to the curb. Now I know that it could have been sleeved. Live and learn I guess.
Permatex 2 is the fix. Just do not forget about that upper hole above the front oil pan rail that will leak oil if you do not plug it with a 3/8"-16NC x 1/2" long bolt . It intersects the passage bore where the mechanical fuel pump push rod goes through .
I was going to comment about that. Have fixed many mystery oil leaks because of that. They change pan gaskets, crank seals, and it still leaks. Well of course 50$ and 5 minutes later a reluctantly happy but pissed off mechanic drives off. Don't worry I won't tell your buddies haha
@user-ie4pv9vv5e Before silicone, we used shellac and laying the threads over each other causes a thickness difference at that point so we'd lay ends side by side thigh together for .25 inch !
The difference between a mechanic and a technician is the mechanic will get you home, no matter what and the technician will diagnose your issue and order a part and hopefully it’ll be there the next day. Pray his scanner was right.
I miss all I remember one time I got my transmission broke down. I park around the corner called to a friend. To go to the junkyard get a used one I 😊take down my and install the one from the junkyard all and the same day transmission 60 dollars 20 dollars to my friend for gas. One case of beer 10 dollars while working HOUSTON TEXAS 1978 What a great times then BY THE WAY I WAS A CONSTRUCTION WORKER THEN AND NOW NO RETIREMENT FOR ME I WILL CONTINUE TILL MY LAST DAY IN EARTH
Looks like a silicone spread with the dental floss crush ! On the mech fuel pump blockoff ! Must be running an electric hi or low pump depending on f.i. or carbed !
My model A developed a miss at the base of a large hill, so I pulled to the side of the road and flipped up the right side of the hood only to discover that one of my spark plug brass leads had cracked and fallen off. I looked around, and in the ditch, I found a Diet Coke can! I took a pair of scissors and cut out a new one from the side of the Diet-Coke can utilizing the emblem, snapped it in place, and drove home! I left the roadside repair in place to entertain the public at future car shows we attended.
I dont know about that string part. But im totally with you on the amount of sealer. I use the gray and try to get it almost clear. Just enough to hold the gasket.
Oh brother. Old school would have glued the gasket to the cover then glued or sealed that assembly to the block. Finger tighten the bolts and let it sit for 15 minutes (using silicones) and then finish tightening the fasteners. Also allow 24 hours for sealants to finish curing. Done...... & done right
@@AlexJonesWasRight1776 what mechanical pump? The video shows a pump port being sealed with a cover.....as for what you choose to seal it with is up to you , it all works. Using RTV sealants is simply an indicator of patience and experience.
I once seen a old man I worked with cut off a piece of his belt and put it in a cup of oil. The next day he dropped the oil pan on a slant 6 and put it in a main bearing. I asked how often he does that he said once a year.
Okay folks .. I think this engine block is being prepared for shipping.He is first sealing the block because there will be some oil in the block and then he adds the gasket under the second sheet metal cover.. The gasket is the one you will need for the fuel pump that gets installed in that location..
Usas dos opciones para sellar un área que no vas a utilizar, en la 1, usas un producto de muy buena calidad, Loctite 👍🏻, si las superficies son 100% planas no necesitas tanta cantidad ni el cordón. Personalmente es la mejor opcion. La segunda sin selladores solo con un empaque o juntade papal, es válida pero de una vida util menor que la anterior.
True old school mechanics made a roadside gasket from the side of a cigarette (or cereal) packet. I've done it in the past, many times, and they lasted longer than brought ones. Good old days!, contact points, condensers, distributer caps, carburettors, fan belts, all repairable at the side of the road with a very basic tool kit. (and a great sense of achievement!) No laptop needed....Just knowledge! Who else misses those days?
How do you repair a fan blade? The servo belt broke, it looked like spaghetti, car became a tractor for the next 80km
Leather bootlace gasket I learned from some old railroaders in the North (Canada)
I still have a 1972 Karmann and a 1965 Falcon Sprint both standard Transmission. ❤😂❤😂
@@c0nstantin86take it off. Eliminates the unbalance. Ans as long as you are moving, the air flow will cool the radiator. Just remember to install the belt.
Manila folders...
Contact cement and a silk thread is still used on piston aircraft engines as an oil pan gasket, only you dont cut the thread and piecemeal it around the inside of the bolt hole, you run it full length along the outer perimeter and loop it back on the inner perimeter, which seals both sides of the bolt holes.
What's the thread for?
@ricos4700 No matter how precision ground 2 surfaces are, they still need some sort of sealing material. Using a silk thread simply shows how precision ground the surfaces are.
@@ricos4700it’s part of the gasket it helps seal between the two surfaces think of a log cabin pack with mud and moss instead of straight cut
@@ZootedSosa Gotcha. Thanks.
Must be why airplanes always leak oil.
So you put a block off plate on a block off plate on a blocked off fuel pump passage? Someone doesn't get GM blocks.
Thats how we do aircraft engines with loctite 515 and 00silk thread But we are taught to overlap threads in certain areas.
but why? the silk works as a gasket?
This looks dumb
He’s putting it on then figures out that it’s shit then puts on a real gasket ?
True
Теж так подумав😁🤝
Muy cierto!
😂😂😂😂😂
Probably something behind the idea of it for later.
In the 60s, we used Permatex #2 with a cotton thread to seal VW engine cases Motorcycle engine cases. Anaerobic sealers are far superior.
I always used yellow weatherstripping glue on vw cases. Never had a leak
@michaelwooda9444 me too until dad brought home some surplus red RTV from McDonnell Douglas Aerospace where he used to work sealing everything from airliners to space capsules.
@@marlobreding7402 🚀🚀🚀😂
We use a silk string on old Lycoming and Continental airplane engines on the case halves. Never leak. That's what he's doing here.
00 Silk thread
Thanks I wasn't sure if that was silk string or not
Silk string is used when placing continental case halves together for aircraft engines. No gasket needed
This guy's delusional 🤣
Right, but he did all the locktite and string thing and still just ended up using the fuckin gasket so my question is why do any of it if you’re just going to use the thing intended to do that job
VW air-cooled case halves only get sealant. An old vw mech once told me his German training instructor said that Gaskets are for piss poor machining 😂
@@justaregularperson23 that’s the same reason I don’t use head gaskets
@@hunter0311able the string was for the plate to the block the gasket for the other side of the plate to the pump…. Or block off plate as I should say
The only pressure on that gasket is crankcase pressure from ring blow by, and it never even becomes 1 psi as the positive crankcase vent is connected to the intake system and engine vacuum sucks out any crankcase fumes.
Actually crankcase pressure can go above enough to blow a seal out. So 1 psi isn't correct.
@@robertragsdale6955it absolutely will not on the small block chevy he is working on. Even with 10 to 1 compression and a cam and headers there wouldn't be 1 psi crank case pressure unless there was engine damage.
A later model vehicle with a factory turbocharger or supercharger could definitely have over 1 psi of crankcase pressure but not a naturally aspirated engine unless the emissions system is designed to work in a way that causes it.
In Vietnam often times we used c- ration boxes for gasket material!!!!
Ive worked all over and the best bush mechanics come from Vietnam. Weld cranks back together, make crank bearing out of bamboo, walk miles down the road picking up pieces of engines, put back in place and keep going.
Bro went bipolar on the fuel block off plate😂😂😂😂😂😂😂
Thermostat hole
Never do twice what they pay you to do once
Unless you fucked up brah
@@SmokingYoMota like I would ever f up.
But wtf does he do it twice!
Twice better, more is better: Jeremy Clarkson.
50 Million small block chevy engines were manufactured without one drop of any type of gasket adhesive or silicone and the oil pressure sending unit was more likely to begin leaking than any of the gaskets.
Preach
How were they sealed. I'll guess- with very accurate machined surfaces and accurate torque tightening. Otherwise those engines would have needed something between the surfaces as pressure builds up.
@@emanuelmifsud6754 just gaskets.
Yes Yes Yes Yes Yes Yes, people make so much shit out of nothing. He's working on it in his shop or where ever. I'll guarantee there a gasket in that overhaul kit.
This is pretty funny because as someone who has worked on scores of SBCs this could not be further from the truth. As a matter of fact, I've had several Camaros and Firebirds and the most rust free areas of the chassis is consistently the firewall behind the engine and transmission tunnels because they profusely leak oil as they age which is blown by the fans into these areas creating a protective layer of grease. First, they are absolutely required to use gasket maker on every single SBC. The oil pan gaskets and the intake manifold gaskets are a multipiece design which MUST have sealant applied. These gaskets are still so prone to leaking the aftermarket has made some one piece gaskets. Assembly instructions for new engines from GM also requires gasket maker around the water ports in all but the newest Vortec engines which were get this, prone to leaking water at the intake manifold water ports! Even GM realized their multipiece rear main seal was a bad idea prone to leaks and replaced it with a redesigned block to incorporate a 1 piece seal back in the 80's. Valve cover gaskets leaked basically all the time. There were grocery stores that literally stocked SBC valve cover gaskets in their convenience aisle back in the day because this was so common. The valve cover gasket sealing surface was not even machined, just a rough cast iron surface up till the mid 80s or so. Being that the valve covers were literally stamped sheet metal you also couldn't over torque them to try and make the gasket conform to the rough surface because then they would bend and leak 100%. On that note the timing chain cover and oil pan were also just sheet metal and would also leak if you did not take the utmost care when torqueing them down. Even then they were again prone to leaking over time. I had good luck keeping them sealed up but they were basically glued together with RTV literally used everywhere.
Skill level of a moose knuckle
I know what that is.
Lol, your killing me smalls!!!
Love it
Can’t afford a gasket 🥴
My buddy had a fuel pump on a international scout go bad that he has owned for 20 years. He took it apart to see what the failure was and compare it to the new one. When he opened it up there was a moon pie box cut out and used for the seal.
It works. I’ve used the spiral notebook covers many times for gaskets.
I’ve installed hundreds of those fuel pumps in the final build department at lycoming engines. Using the tread with the gasket doesn’t make sense. The case halves are assembled with a thread seal and that’s it. Wasting time to make it look cool for the videos is the only reason for this.
Watch again, it's 2 different methods back to back. You;re right the silk thread works, but takes longer.
This is typical of CZcams. Someone decides to show a wrong method. No proof checking until tradesmen correct them . Thank you for your comment.
Loctite taste good, and really sticks to your stomach.
Adding his tiny acid layer from our oily hand.
This is the silent sound of....
Im not sure this is showing anything worthy of a video. This is showing someone doing unnecessary things to probably and old 350 converted from mechanical to electric lift pump. Slap some grey silicone on clean surface, go take a dump, smoke cig, drink coffee or beer, allowing silicone to tack up and install fasteners with torque wrench. Loctite though?? What is the point of the red Loctite?? Not only is that shit expensive, they make silicone for this application, maybe he no get the memo.
❤
Silicone sucks for oil bathed surfaces you went to seal. Try some form a gasket or case sealant…
St least some right stuff from permatex…. Not silicone gasket maker 🤦🏼♂️
@GR40RCapri I 100% agree with you that if you do not have a properly cleaned oil free surface to start with then that silicone will not work and just make mess. If surface is completely cleaned and void of contaminants and you let it tack up properly before torquing bolts. It will certainly work,, but, whenever possible I would certainly rather use a gasket. That's a no Brainer. I was just commenting on him using Loctite which I know is just ignant!
Dammit just got a little dumber again! Gotta stop with the CZcams shorts.
That song is more relevant today than it ever was. It's a secret message behind that song and it's coming true.
I guess you never watched The Challenger documentary using a thread as an O-ring
Challenger space shuttle?
@@klamup🤣🤣🤣
But those were made in a kitchen.
only old school mechanics know this very good technic.
Please explain why this is a good technique.
I also wish to know 😕
I'm very old school and have never in all my days have I seen such nonsense.
This is NOT old school.
Year I'd love to hear. Especially about the string and putting it on then taking it back off just so you can then put it together with the proper gasket. Makes no sense
This is a carburetor engine. He replaces the gas pump with a plug and then installs a modern electric pump.
The silk thread is great! So are the flexible sealants. I grease those stupid paper gaskets so they don't form the bond from hell when I disassemble. I am a little curious how calibrated your screwdriver torque method is. I doubt you got a proper stretch on the bolt to keep it secure.
I think he's sealing up the mechanical fuel pump in order to use an electric fuel pump. Good job.
Egr
No, Chevy V8 fuel pump and he did poorly
Clickbater in the End he used the gasket
Looks like hes blocking off the old Mechanical fuel pump to use an electric fuel pump, just an upgrade
That's a downgrade to me. I have a Gen V 366 tall deck with no place for a mechanical fuel pump that I don't like. I picked up a Gen VI that has a place for a mechanical fuel pump but it had a cracked cylinder so I set it to the curb. Now I know that it could have been sleeved. Live and learn I guess.
upgrade for sure. Electric pumps no need to refil carby if its sitting for too long, doesnt leak fuel into the engine oil when they break etc
Bingo.
2 cover plates? No necessary!
Дренаж турбокомпрессора
Locktight flange sealant is awsome. Should of used the activator with it aswell
Sure is. Laugh at all the know alls in the comments bagging it out.. Sealed heaps for truck diff centres and never leaked
That 515 anaerobic sealant is all that is used on modern farm tractors. Except engine.
Permatex 2 is the fix.
Just do not forget about that upper hole above the front oil pan rail that will leak oil if you do not plug it with a 3/8"-16NC x 1/2" long bolt .
It intersects the passage bore where the mechanical fuel pump push rod goes through .
I was going to comment about that. Have fixed many mystery oil leaks because of that. They change pan gaskets, crank seals, and it still leaks. Well of course 50$ and 5 minutes later a reluctantly happy but pissed off mechanic drives off. Don't worry I won't tell your buddies haha
что он сделал? без пальца конечно никуда, но нормальный герметик без этих танцев справился бы
И...
У него была прокладка...
Надо немного переосмыслить бытие 🤔
Never overlap gasket threads !
У прокладок есть резьба🤔⁉️
@user-ie4pv9vv5e Before silicone, we used shellac and laying the threads over each other causes a thickness difference at that point so we'd lay ends side by side thigh together for .25 inch !
I think this is useless
Once a wise guy told me......sealers are for plumbers....
Guess you ain't worked on many engines
Shiming a fuel pump in this case capped off and electric fuel pump is added else where
Просто глушит отверстие от старого бензонасоса. Такой толщины металла не достаточно
The difference between a mechanic and a technician is the mechanic will get you home, no matter what and the technician will diagnose your issue and order a part and hopefully it’ll be there the next day. Pray his scanner was right.
I miss all I remember one time I got my transmission broke down. I park around the corner called to a friend. To go to the junkyard get a used one I 😊take down my and install the one from the junkyard all and the same day transmission 60 dollars 20 dollars to my friend for gas. One case of beer 10 dollars while working HOUSTON TEXAS 1978 What a great times then BY THE WAY I WAS A CONSTRUCTION WORKER THEN AND NOW NO RETIREMENT FOR ME I WILL CONTINUE TILL MY LAST DAY IN EARTH
Ah yes, silk or cotton thread as a gasket, old way to get things done.
Probably dental floss. It has a waxy type texture
Only way to do case halves.
This guys knows what he’s doing it’s
Better than actual
Gasket
😅 that's a no pressure gasket you can literally do anything to seal it
Silk thread is an aircraft mechanic trick
An explanation of the process would be good
He’s using silk thread as a gasket. People have been doing that for many many years. Even in airplanes if that tells you anything.
Doing unnecessary shit. for clicks.
@@toejamr1So what is the blue gasket for? 😂
@@chinhphan4787obviously to double up for sturdiness and no leaks use your head kid
@@toejamr1
and anaerobic gasket sealant.
Bro thinks his bung
Hole is a lycoming engine case seal wtf
The handiest gasket material I use separates 15 beers from 15 beers in a 30 pack.......
Looks like a silicone spread with the dental floss crush ! On the mech fuel pump blockoff ! Must be running an electric hi or low pump depending on f.i. or carbed !
Ya think?
My dad once made a main bearing from oil soaked l piece of a leather belt..
My model A developed a miss at the base of a large hill, so I pulled to the side of the road and flipped up the right side of the hood only to discover that one of my spark plug brass leads had cracked and fallen off. I looked around, and in the ditch, I found a Diet Coke can! I took a pair of scissors and cut out a new one from the side of the Diet-Coke can utilizing the emblem, snapped it in place, and drove home! I left the roadside repair in place to entertain the public at future car shows we attended.
Is he blocking off the mechanical fuel pump port on a SBC?
Lmfao all that bullshit to put a block off plate on 😂😂😂😂😂😂😂. This is true fresh outta tech school knowledge.
I dont know about that string part. But im totally with you on the amount of sealer. I use the gray and try to get it almost clear. Just enough to hold the gasket.
Oh brother. Old school would have glued the gasket to the cover then glued or sealed that assembly to the block. Finger tighten the bolts and let it sit for 15 minutes (using silicones) and then finish tightening the fasteners. Also allow 24 hours for sealants to finish curing. Done...... & done right
Noold school we put that mechanical pump back with a quality gasket with no rtv bs on it.
@@AlexJonesWasRight1776 what mechanical pump? The video shows a pump port being sealed with a cover.....as for what you choose to seal it with is up to you , it all works. Using RTV sealants is simply an indicator of patience and experience.
Just use RTV.
I once seen a old man I worked with cut off a piece of his belt and put it in a cup of oil. The next day he dropped the oil pan on a slant 6 and put it in a main bearing. I asked how often he does that he said once a year.
It's a fuel pump block off plate buddie calm tf down. Even put a mark next to the bolts😂
A high level of stupidity in these comments!! Lordy people 2 methods and both work! Rtv isn't always the answer!
Don't touch silicone the oil from your fingers will cause it to leak. Basic mechanics and said it in the directions.
That and the air bubbles created from smearing it with a fingy cause the leakies.
I seen my dad make a muffler gasket for a lawnmower out a beer can!!
Never had a fuel pump block off plates leak on my ford engines.
I guess GM has major issues with theirs!
An old-timer would have left the mechanical fuel pump in it because it's better than anything that you're replacing it with
Whenever he needs a pump gasket,he knows where to find one... 👽👽👽
Those things always end up leaking, but this is ridiculous. Just use shellac sealant for this on both sides of the gasket and be done.
What the hell is he doing with the string?
Why? 🧐
Mechanical fuel pump delete, he is switching to electrical.
For the "get you home" repair
Okay folks .. I think this engine block is being prepared for shipping.He is first sealing the block because there will be some oil in the block and then he adds the gasket under the second sheet metal cover.. The gasket is the one you will need for the fuel pump that gets installed in that location..
Look again. It's 2 different methods. One is a precut gasket and the other is a thread and anaerobic sealer.
Pardon the fuck me bud
UltraBlue and a gasket would be fine..
You guys her the guy in America Got Talent .😊
Closing off the manual fuel pump to the camshaft 😊
Well at least he did it correct the second time.
Open mouth, insert foot. Instructions unclear. 2 ways of sealing.
Good bye EGR DONT LET THE DOOR HIT YOU IN THE CRITTER
Someone should tell him the gasket should go between the block and the delete plate 😂
The plate was installed then removed and a gasket placed, then the delete plate reinstalled
@@robertragsdale6955 Oh yeah, missed that.
Волосы с лобка надо было накрошить , тогда точно течь не будет
Why the hell are you worried about those bolts backing out?
The song is low key fire
a dollar bill works if you don't have dental floss and the permatex.
Why is he putting a gasket between the plates and not before them??? What is supposed to leak😭🤣
The pubic hair trick.
It looks like a mechanical fuel pump delete. Just get the correct gasket.
At least there is knowledgeable commentary
А на прямую через прокладку крышку бы не прикрутил! 😂
Usas dos opciones para sellar un área que no vas a utilizar, en la 1, usas un producto de muy buena calidad, Loctite 👍🏻, si las superficies son 100% planas no necesitas tanta cantidad ni el cordón. Personalmente es la mejor opcion. La segunda sin selladores solo con un empaque o juntade papal, es válida pero de una vida util menor que la anterior.
Simon & Garfunkel cover. 😂😂😂 Inscrito!
Dental floss as a back up to the rtv , what no sheet metal plate, when you don't have a steel cover, mmhh
Right Stuff seals great but is God awful to remove when cured
That's why you use it with a cardboard gasket. That's how I was taught, anyway.
The metal cap is too thin, so might as well put no gasket..
Please do not butcher that song lol. It was much better the way they actually covered it. Not when it's sped up and altered.
That's what I keep saying! Just butchered it
Simon and Garfunkle did not use autotune. Both the music and the cars were better back then. F#%$ am I turning in to my Grandfather?
Simon and Garfunkle did not use autotune. Both the music and the cars were better back then. F#%$ am I turning in to my Grandfather?
Am I the only one asking why all that string play when he just uses a gasket?! Two words people Fel Pro! Problem solved 👍🏻
what's the white string like stuff?..
I glue my butt hairs to my engine blocks. Does the trick!
Guessing some sort of delete kit.
That's very basic I used to do more than that when I was a teen always fixing cars take engine out fix and put back.
Good grief!
how absolutely unnecessary.
Little hi tack and a piece of cardboard from a beer case
Ооо я думал только я нитку улаживал,
The aerobic sealer sufficient. He could throw the gasket away
That's loctite not sealer 😅
@@BlackandWhitecustoms loctite is a anaerobic sealant 😅
@@Mad-productions.Jay. oops 😬😂
@@BlackandWhitecustoms It's anaerobic sealer made by Loctite. Google it
I do not think that thin plates apply enough compression to that thread at the farthest portion. Another casting, more likely.
should use gasket sealer with whatever type of gasket you are gonna be using