Build This Simple Table Saw Outfeed and Assembly Table - Part 1 | FREE PLANS
Vložit
- čas přidán 10. 03. 2021
- Everyone’s workshop need a large assembly space. Everyone’s workshop needs a sturdy outfeed table. Here’s how I saved space and smash these two things together.
Part 2 of the build where I add drawers:
• Add Matched Grain Dra...
*PLEASE SUBSCRIBE*
Disclosure: Links contain affiliates.
As an Amazon Associate I earn from qualifying purchases. When you buy through one of my links I will receive a commission. This is at no cost to you.
Thank you for supporting Bear Mountain Builds and allowing us to continue to bring you valuable content.
*Products Used*
T-Track Intersection Kit:
amzn.to/3FhBEtP
T-Track 36":
amzn.to/3DdWxp5
T-Track 24":
amzn.to/31XhV49
Four pack of 4" Caster Wheels:
amzn.to/3CbjI1X
100'' Straight Edge Saw guide:
amzn.to/3UhCOxz
Silicon tray and brush set:
amzn.to/31Lwnfl
POWERTEC T-Track Clamp Vice:
amzn.to/3wOZVo0
Hot Favorable T-Track Hold Down Clamps:
amzn.to/30oFsuk
Kreg Pocket Hole Jig
amzn.to/3OActbD
DEWALT circular saw:
amzn.to/3MCtwsz
DEWALT impact driver & drill:
amzn.to/49SAvbc
DEWALT bit set:
amzn.to/3g7ddHT
MY GO TO TOOLS
100'' Straight Edge Saw guide:
amzn.to/3UhCOxz
DEWALT circular saw:
amzn.to/3MCtwsz
DEWALT impact driver & hammer drill:
amzn.to/3CVhS8U
Bosche miter saw:
amzn.to/3i8gdVz
DEWALT bit set:
amzn.to/3g7ddHT
Gorilla glue:
amzn.to/34ULnJK
6'' Clamps:
amzn.to/3IARLqM
12" Clamps:
amzn.to/38oDWMZ
Delta Table Saw
amzn.to/3WL7d7s
*FREE PLANS*
PLEASE SUBSCRIBE if you're using my free plans
www.bearmountainbuilds.com/pr...
*Filming Equipment*
Canon EOS M50 camera
amzn.to/3t39P46
Tripod(best tripod ever)
amzn.to/3WwAnbz
Hand held Tripod
amzn.to/3NB06LX
Universal camera mount
amzn.to/3WxKTzc
Lavalier Microphone
amzn.to/3l82Eqx
RODE wireless GO microphone
amzn.to/3DF8yW3
Directional Microphone
amzn.to/3UugnEM
Adjustable Lights
amzn.to/3Dzszx4
Set lights(mainly all that I use)
amzn.to/3WBjDQo
FREE PLANS!! ** PLEASE SUBSCRIBE **
www.bearmountainbuilds.com/pr...
*Bear Mountain Build things*
Instagram: / bearmountainbuilds
Facebook: / bear-mountain-builds-1...
Bear Mountain Builds Homepage: www.bearmountainbuilds.com/
Patreon: patreon.com/BearMountainBuilds - Jak na to + styl
I am almost finished with this build. I have learned so much from you. It didn’t turn out perfect, but I think it’s great.
This is a pretty solid little workbench. While once you figure out how it comes together, it is physically Easy to assemble czcams.com/users/postUgkxyFZUPFEey-PuqsPMxqaykBhgA1LWxFHh by yourself. But the diagrams explaining the steps are really pretty bad. I could not get the handle pins in all the way despite multiple attempts, so I just used a screw I had on hand for the 2nd handle. I could not get the first pin in further or pull it back out. You are supposed to hammer it in, but I had no leverage and the handle is plastic and I did not want to risk breaking it. I will get a lot of use out of the bench because of the convenient size and height. It does fold up nicely for storage. They even explain how to fold it so you don't get pinched...that is important!
I am a Naval Architect and an engineer and so I appreciate instructions that are to the point with no unwanted embellishments, which some times confuse the issue. In this department you achieved top marks. Thanks for an excellent video. Keep up the good work.
I am at least a year late to the "I'm new to CZcams so please leave a comment" party, but before this video was halfway through you had my subscribe along with a thumbs-up. I started woodworking with my grandfather and an uncle before I started kindergarten, and I love your super-sturdy laminate legs and tabletop. This is just a great entry in the maker channels.
I love having everything on Castor since I’m only 5’3”, and my workspace is a little tight. It’s so nice to be able to move things around as projects change. I never imagined myself doing these things at 64, but I’m so grateful for CZcams channels like yours! ❤ it allows me to go at my own pace and watch things over again if I missed something. I love items that can be used for double duty with small spaces it counts!
I like your ideas and your concerns for " rock solid-ness ". Great looking table but I would have to tweak it to work with my DeWalt job site saw
I've built one of your projects before and find these really helpful. Your storage unit I built is so strong everyone that sees it wants me to build them one. Thank you for doing this for those of us who want to DIY our shops. I need this on my farm.
I love the concise instruction, the transparency, and "let's keep going"! All the best 😊
Thanks for the free plans, I’m currently in the middle of building this much needed out feed table.
Thanks for sharing your skills and for the free plans. This is the answer to tidying up my garage workshop/dumping ground. Just need to convert feet and inches to metric even though I'm so old, everything I was taught in school was in feet and inches, dozens, pints, miles and something else I don't remember. Just so long as they don't mess with our currency. Oops, they already did that. I can still buy a dozen eggs though. Keep up the good work thanks again.
Really like how you did this learned a couple new things just starting my wood trade lol. Been a machinist for 40 years but love working with wood always have. Router station will be my second build. Thanks for your insight.
Great build !
I love watching you make stuff ! It gives me the incentive to make my own stuff. Love your channel!
I watched it all and enjoyed it, great job! I saved it because its got some of the best background tunes Ive heard in one of these videos ever! Love it!
Thanks! The plans are great!
Great video. Thank you for sharing your mistakes as well as the finished product. Helps us newbies learn.
Probably the best videos and instructions I have seen thus far.
The project turned out really well. I enjoyed the build process and will be sure to use some of your ideas and techniques myself. Cheers 👍😎🇦🇺
One of the best table builds I've seen. Thanks for sharing. I've downloaded plans and seriously have this one in consideration. Good luck on building your CZcams channel.
Great build mate, I’m looking forward to the drawer/cupboard fit.
Please keep the videos coming. 👍🏻
Thank you for the plans!!! I have a BT3100 and really wanted to do something like this.
That is a high quality and impressive beast. I've been searching and viewing videos for a large outfeed table for a Dewalt contractor table saw, and your build is by far the best.
Just discovered your channel and def one of the best assembly/outfeed tables I've seen. Subscribed and downloaded the plans. Thanks for your generosity and your time!
Great project and a great job !!! Inspired to build my own !
I’ve been looking for a base set of plans for awhile, these are great. I would like to modify making in a bit narrower to fit and have adjustable power tool shelf to additionally accommodate a chop saw access from sides, small router table from the end and combo belt/rotary sander. Thank you!
Never thought about using a ratchet strap for clamping! Genius!
Great video. I’m about to start woodworking myself and your video is a great tutorial. I’ll be building a smaller bench but this is exactly what I was looking for to get a better understanding. Also, I like your personality, it’s very entertaining. Keep up the great work. Came for the video, liked it and subscribed to your channel 👍
Thank you for your videos and plans to help me build tables for a functional work space.
Great build!!! I plan on making this for my shop.
Amazing.I have been trying to find the right build for my workbench for the last 2 months And after a lot of searching yours was perfect. Especially the legs. I glued 2x4x8 together and then saw your process. Shoot me in the head. So eaaaasssssy!
Thank you for this!!
Very well done and generous of you to share your plans!
Exactly what I was looking for.
I would really like to see the detail of how you allowed for space in the table top for the sliding miter table on your Ryobi BT 3100
i like the simpleness of the project. I'm just starting out so I don't need to get fancy for now - i just need something that'll accomodate my table saw!
One thing I'd like to implement i saw on another build was a flip top area for a miter saw. i'm not going to have enough space for multiple work stations, so having a miter saw in the middle area may be the best way to go.
This table saw is just great, buddy. The size is spot on. This is my second build after your mitre station. Excellent. Keep it going.
I don’t have room for a table like this, but I was going to use the modular work benches for this purpose. I’m trying to figure out what I’m gonna do with the tablesaw how to mount it to work with them? Any suggestions?
Yep I have been an Eve Emerald (menthol) 120 girl for a very long time! I used to Be a Virginia Slim 120 girl but LOVE Eve 120s much more!
That’s a pretty sweet setup. Well done.
I like the way you work. Will look for more. Thanks!
The best outfeed table I've seen.
Fantastic job!!!!
I loved doubling the plywood.
With mine, I built it too big. Ran out of shop space.
Thank you
Glad you like it! I have a pretty decent sized shop and it still feels like a giant table so I get what you mean
Enjoyed the design, the build and the music! Looking forward to more projects.
Great video. I'm going to attempt to build this one. This would be my first wood working project so why not start with something I would need to build other projects! Thank you, look forward to watching more.
Great Vid! I like how you build the uprights first…well done!
Your video rocks. Your plans rock. That they are FREE is unbelievable. Thanks for everything you are doing. Sub'd
Wish more youtube build craftsman were good role models like you when it comes to safety. A flick of a chip and you lose an eye. Hearing protection, even for just a single cut, reduces long term hearing loss. I appreciate your explanation skills and inclusion of plans. Thanks!
And I really wish that you take care of you, and let me take care of me
Wow! What an awesome table. I wish I had the space for one.
You can always make a shorter version of it or check out my latching workbench which is perfect if you want a large work table for smaller spaces
I like that you used drywall screws for the T-Track. Drywall screws are perfect for plywood, and being black, they look nice against Birch.
Muy buen trabajo amigo. Me encanta tu proyecto.
Beautiful table! now as a retired professional woodworker ascetics were not worth a hill of beans, Instead of using expensive plywood I would have used blond MDF and covered with Formica before routing those rails. MDF provides an extremely level surface that does not change much with changes in temperature and humidity. Formica lends to a very smooth surface but is extremely durable surface for saw out tables. Of course the table I built incorporated an Italian sliding table saw with a 14' sliding table. I did not mount my table saw, I surrounded it. Also, with Formica laminate you don't have to worry about glue spills, wipes right up.
Awesome I look forward to building this.
Good job. Enjoyed watching
Hey Zach, yours are some of my favorite videos on YT. I downloaded your table plans as I am building out a shop in my 3-car garage. This will be my centerpiece work surface. Great plans, especially with the companion video. IT IS BEAUTIFUL! I must say I am very pleased. HOWEVER, either I suck at routing or my router/bit were not up to the task. First I used my ooold Ryobi corded router with a 3/4 flat bit. Using a track saw guide for straightness (cough, cough) a-routing we did go. Yep, over the river and through all my straight lines. Holy cow, what a freakin mess. And the choice words I used. Visions of ripping off my brand new 1.5" top danced through my nightmares. Now my only option is to use my cordless circular saw with TWO straight edges to clean a reference edge on one side of my channels and do a LOT of wood filler on the ugly side. Man, what a mess. But with my rant over, everything else about this table is spectacular. The carcass is done and I am building the drawers as I write this. I'm going with Minwax Classic Oak on the top and a darker tone, maybe Espresso, on the frame. I didn't care for their Classic Black stain. Too dark for me. But dude, this table is fabulous. Thanks so much for all you do. Let's make some sawdust!
Thanks man, good luck with the build!
great mobile saw table. simple build, a good all day project.
Hey, good to find you, installing new tracks and liked your layout. Plus we have the same design style and daily fireworks show. But I have never mismeasured before.
Great job, l personally do not like having my main tools on one table ie mitre saw and planner, and you have put the table saw the proper way for long cuts, again great job.
I like it. 👍 Should work well after I finish cleaning out my garage with New Built Cabinets and French Cleat System.
Great job. I’ve been researching these tables all day and after a dozen or so options, you’re is clearly the winner and I will be starting my build now. I like that you set it up to build in two stages so I don’t have to have a giant incomplete project waiting to get the drawers etc done. Thank you!
Thanks!! I really appreciate you letting me know you like the table!!
The build is in progress and going great! Are you in Bear Mtn, NY? If so, it’s great to see a local woodworking CZcamsr. I am in Bergen County, NJ. Keep up the good work!
Worth mentioning is that an essential prerequisite for a large rolling table is a dead flat shop floor. Wedges under casters is a kill joy.
Actually, this thing is so big and heavy that unless your floor is ridiculously uneven it doesn’t need any wedges
Great job
Nice job.
You made that look easy!
looks great. Thanks for sharing.
Well done.
Pro tip. Use impact rated sockets
Thank you for the info
Looks great , functional and not overly complicated. I'm new to CZcams too.
Thanks!!Welcome to the party!
@@BearMountainBuilds it's been a fun ride so far. Looking forward to connecting with more people and improving my skills.
I'm a "measure 4 or 5 times" or more person too. The minute I don't do a quad measure I miss it by an inch. Well done sir!
Glad to see the you show your mistakes and looking forward to see your dust collection solution. I'm have the Harbor Freight collector and haven't decided what direction I'm going with modifying it. I hope you pick the same one so I can follow along. Liked, subscribed and commented 👍
I’ll keep that in mind. I’ll need to do some research into dust collection
Nice build Zach, well done video also. I was searching for a workbench build and came across your channel, I watched your video and subscribed to your channel.
A new subscriber from Iowa.👍
Welcome to the channel!! Good to have a fellow midwesterner since I’m from Minnesota
Thanks for the free plans, subed
Fantastic. I really think this is a project th as t I could tackle
I’m glad you like the video!! I hope it encourages you to go for it
Really GREAT table, Zack!! Excellent!!
Happened to catch the 1 (ONE) anti- pocket hole comment. Some people display their ignorance for all the world to see.
You ARE using pocket holes for EXACTLY what they’re for, so remain secure in your skills, methods & knowledge!!
Lotta people have your back, including skilled veterans of wood crafting. Don’t even worry bout it! Pfff. 😁
Thanks for the video. The project came out great. I just started you modular workbenches and will move to this next. I really appreciate the plans. They make it really easy. 19:24
Thanks!
Another test you should do is the cross-angle test: Measure from one corner to the opposite "catty" corner. Now do the same for the other pair of catty corners. The measurement should be very very close to the same. If not, you are not properly square somehow (perhaps your boards are warped, or perhaps one is actually slightly shorter than the other).
You do this to check for square in a way that simple angle checks cannot do -- squareness over the whole length of a project, which, for a project this size, is quite important.
P.S., like the ratchet strap idea.
Great camera moves!
Subscribed. Every few minutes I found myself saying "damn that's smart". I have watched a LOT of CZcams woodworking videos, and you are FULL of awesome surprises!
How long have you been doing this? Any formal training? Would love a video on this by you and other CZcamsrs :)
One of my favorite channels now!
Thanks I really appreciate that you’re liking my channel!! I’ve been at this for a little over a year now. I’ve never had any formal training, I work as a mechanical engineer for my day job though. That’s not a bad idea, maybe I’ll put together a video about me someday
Great video with mice music background.liked your video , simple with clear explanations .
Looks great. No interested in t-track but looking to add my mitre saw (maybe on a hinge?)
awesome!
Good job kiddo
Great work congrats
Nice build. Have you given thought of using the Micro Jig system for making it a assembly table. I did that for mine and LOVE IT!
Solid well made table Wanting to mount my table saw in the table like yours.Why did you raise it one eight above the table .I was gonna mount my flush with the table . Agree FYI the music was very loud i would lower the volume for the music and when you would speak i had to raise the volume back up.8 wheels on the bottom nice nice!
I did it so that if I ran any boards through my saw that bow down they wouldn’t catch the edge of the table. I think if I were to do it again I would flush mount it and just round the edge of the table
One word,cool!!!
.
lets get going !!!
Thanks so much for this video. I've got some great ideas for what to do in my shop. Mine is much smaller than yours so I may have to be a little less ambitious on the dimensions :-)
You earned a subscribe from me once I saw your table saw.
I love the table and definitely subscribe to your station! I'm looking for the plans you said that we're free online to try it myself.
The link to my plans is in the video description
I feel sinful getting these plans for free. They are very good, well worth at least $5. Thank you for the service you provide your community. I gave you a sub as payment for the plans.
Thanks!! That’s all I ask
Thank you for the plans. Great video. I see you're using a Ryobi BT-3000 and it looks great, I have one too that is much dirtier. How do you keep yours so clean?
Great table, will be making it for my new workshop. Thanks a million. Can I turn down the loud music?
What kind of table saw do you have? I don't think I have ever seen a set up like that again. Your table build is awesome! Your attention to detail is very refreshing also. I am seriously considering adapting your plan for my workshop! Great work!
It’s an an old RYOBI 3000 that finally bit the dust about a week ago. It’s a job site table saw
Outstanding work! I also have an older Ryobi BT3000, question, is it possible / necessary to add a cross-cut sled that would work on the BT table saw?
I'm thinking of doing a similar table in my shop and this is a great looking build. Did you ever install shelves? Thanks for the video, keep posting 👍
I actually just finished putting the drawers in yesterday! Hopefully I can get the video out in the next week or so
Your help is a keeper. Most women won't help on projects. Bravo!
I like how the work bench has phases and you don’t have to do all of them at once.
Love the plans and video. Great job. I am planning to build the table but using a DeWalt 7485 table saw. I noted your Ryobi table saw is quite different. Any thoughts on needed adjustments to use the DeWalt 7485 that you can share? THANKS!
I’m glad you like the table!! All I can really give as a recommendation is you’ll want to move the tracks that the guide mounts to on your saw all the way over so you can get maximum board width for a cut. Then use that position to measure the width and depth of your table saw to determine the size of the cutout in the table for the saw. Then make sure your saw is positioned as far to one side of the table as possible similar to where my saw is positioned in the video. Additionally, the platform holding your saw will be at a different height, but just make sure to keep the table saw top plate 1/16”-1/8” above the table surface.
Wow…nice..
Wow!!!
I. agree music very annoying some of us are a bit and cannot handle heavy metal music. Some great tips great explanation.
Got to say I love your channel. Just in the process of building this table. How much clearance do I need to leave for the table saw?
Generally the tighter the fit the better. Just make sure to leave room to allow the rip fence to move
What I have missed is what the overall dimensions are. Thanks, nice build.
Pretty much 4’x8’
@@BearMountainBuilds Thanks!
just came across this video... loving the table! It's exactly what I'm looking for, and am going to use it as a template.
Just curious... did you find putting on 8 casters to be overkill after the fact, or were they necessary to carry the load? Just wondering if it would sag somewhat without the center ones. Thanks again, looking forward to future videos!!
I’m glad you like the table!! When I was designing this I was going back and forth between using 6 or 8 wheels, but decided to go with 8 because I’d rather have it be too strong than not strong enough. After I built it though I was really glad I used 8 because it lets it roll a lot easier especially with the table being so heavy. It also let me put a wheel under each vertical frame piece which means there is no bending of the frame
Zach, you are Minnesota's younger, hipper version of Bob Villa from the" This Old House" DIY show.
You know, I’ve heard that before