Engine Stuff You Should Know - How To Identify Mystery Cams The Quick And Easy Way Measuring Lift
Vložit
- čas přidán 10. 11. 2022
- It's not always easy identifying camshafts. Very often their ID numbers are stamped sloppily, or too lightly, or in the case of this vintage Chrysler Direct Connection cam, sometimes there are no numbers at all.
Here's a way that you can ascertain one simple measurement from your camshaft, and with a little detective work, find all of the other specifications for it from published catalogue listings online.
#camshaft #lifters #engines #diy #classiccar #musclecar #racecar
MERCHANDISE:
Get Your UTG T-Shirts Here: uncletonysgarage.com/product/...
Get Your UTG Stickers Here: uncletonysgarage.com/product/...
OUR STORE: uncletonysgarage.com
*SOCIAL MEDIA:
Facebook: / uncletonysgarage1 - Auta a dopravní prostředky
Anyone who belittles a beginner, is an ass. You, "uncle tony's garage" and I, share the desire to pay forward our accumulated knowledge to the lesser learned. It astounds me how many want to say crap to the starter's. We, ALL OF US knew nothing at one point. Thank you "Uncle tony's garage"!!! Edit (I don't have NEAR the experience that you do with serious 1/4 mile drag cars, nitromethane, ect. But rather a very long list of budget builds on small and big block Chevys. That continues to this day. So many are hell bent on "everything perfect, factory specifications" type of building. Not everyone can afford this. One can have a lot of fun, gain a great amount of knowledge, by just doing the best you can, with a very measly Budget. Patience is the main key. Thanks again UTG, you are one of the few!!!)
The first time.... everyone who started on their own with a manual and no mentor forgets how long that first time took. The first time I popped out a valve must have taken me half a day because I was nervous about breaking something. Same with installing break springs. Do it a half dozen times, learn a couple little tricks, get it done in no time at all, and you feel like a god.
First time I built engine I didn’t knw how a torque wrench worked.
Didn’t realize I had broken it removing flywheel bolts.
I thought torque wrench was for high torque fasteners 😂
Took that engine out 3 times
Heads kept coming loose. ..
My fuck did it turn me into hell of a mechanic 20 years later 😂😂😂
We started off with lawn mowers, then riding tractors, then minibikes and go-carts, the family car and then our own when we began driving. As kids, the only money we had was from our McDonalds and Ramada Inn jobs, the local steak house, etc., so we drove beaters, such as the olds Delta 88 455 big block from down the street or across town when someone decided they wanted a new car. Our $500 big block one tire fire cars were fast out on the highway, lol. We had fun, you can be sure, dang lucky none of us were ever hurt.
@@thisisyourcaptainspeaking2259 I can truly relate to that. Cheers😊
It's great you are helping to preserve our hobby showing people how to work on there hot rod .
'their'
Send Josh my congratulations, at least for getting this far. Thinking about doing it is a lot easier than turning wrenches and actually doing it.
I still can’t believe that I got to shake hands with the legend that shares all this amazing information with us :)
😊😊😊
Love u brother man
❤❤❤
UTG in my opinion.
Is my favorite car CZcamsr.
Period.
Well done video! Thank you so much. I recently inherited a late 60's SBC and was hunting how to identify the camshaft. This makes it easy to know what I have. PERFECT level of technical speak; not over our heads but also assuming that we know the basics. You know your audience!
You answered my question at the end about the hydraulic lifter not being as "stiff" as the solid, used to have to adjust my solid lifter cam, a GM phase 2 that was a 512 lift at .28 intake and .30 exhaust, if I remember correctly. Again good content and infro uncle Tony.
For a novice who hasn't been wrenching all their life , getting that transmission out is an achievement .
I been turning wrenches for decades and I can tell you that job would have seen more than a couple tools test flighted .
Great info on demystifying random cams for those that have not had that special treat .
Yeah , the good ole days were not all that great , but , everything is NOT online .
We traded local gurus for internet forums , social media , and , a parts counter person who needs your year make and model just to sell you 10' of 5/8" heater hose .
007
I started working in a shop that did major engine work at 14. My boss took the time to be a meantor. I never took that for granted, and have tried to pass on the favor when I could. You remind me so much of him. I am now 57, and had the chance to thank him and spend time w him after he got dimentia. Keep it up!
I had a guy give me a purple shaft cam years ago and he didn't know anything about it so with this info now I'll be able to. Thank you for putting out the info
Very impressed with the kid! Remember this word, perseverance. There is no greater power. Use it & you will succeed.
Bloody good uncle tony…!!!!
The other handy thing to know for the viewers is tools like digital vernier calipers and Dial gauges with magnetic base
they’ve come right down in price and there’s plenty of $30 and $50 jobs on eBay that’s good enough for the home gamer….
At my Dad's I have a pile of 60+ SBC/BBC camshafts. Most are in the right boxes and identifiable but some of them I have no idea without degreeing them in a block so I'm glad you put this video together. It will be handy.
Love seeing a young-un wrenching on vintage steel.
Its guys like him that want to learn it without excuses that make you want to pass it on.
Hat's off to Josh for this.......... and on a side note.... I was wondering if he would toss those headers after all that, because I sure would've.... lol
Oh they're freakin' gone, hah.
@@joshwilson8354 thanks for the lesson. I have manifolds on my 440 and I have been going back and forth about swapping out with headers. I think I’ll
Stick with my manifolds 😂
A big block plus headers requires a certain type of determined mind in some cars. I knew a guy who stuffed so much motor in his car, he had to undo the motor mounts every time he wanted to change plugs. The hood stayed off that car most the time, and local police always found that... interesting.
That was awesome. I really like the grass roots simple but effective technique to get the solid numbers. Great work.
AMAN of the header delete. worst mistake i made on my ford 390. Regular manifolds are plenty. I never noticed the difference in power with headers.
Funny enough, just bought a cam for my MEL engine to replace the original (early 1958). The one I bought is a later “improved” cam, and I was wondering how I’d measure it up to the original. What luck this was posted today! Thank you, Uncle Tony!
Back when dinosaurs roamed the earth, before the internet, things I was able to dig up on the LA engines, specifically the 318, I found the recommendations for the Mopar "purple shaft". But I was led to believe that was only one cam. But nooooo. There were several. There was also the .474" lift and .484" lift cams, which were also "purple shafts", and the one I wanted, I found out, was the .450" lift, 268* purple shaft. The internet sure makes things so much easier these days. Something else I discovered, cam lift vs. displacement. The same cam in a 318 gave far different performance from using it in a 340. The 273 "Commando"/"Charger" engines had a hot cam, you'd have thought it was huge, but only .425" lift or so. Comparable cam in a 340 would probably be the .474" lift cam to that little 273's cam. I'd be interested in a good discussion of lift vs. displacement.
The greater the displacement for a given head the more duration and lift it needs to perform over the same rev range.
My first transmission R&R was when I was about 18. Ford Elite up on blocks and I took it out by hand. Going back in, same thing. Except this time, it slid off the dowel pins and torque converter studs while I was holding the tail shaft up with my foot and reaching for bell housing bolts. The Ford bell housing has a complete bowl shape, no cutout for an inspection cover. That's an important part of the story because the bottom of the bell housing landed on my chin. The torque converter slid forward and started draining itself on my face. Now I'm trapped! I have no idea how I did it, but I got the torque converter back into place, lifted the transmission back up, somehow got the torque converter studs lined back up with the holes in the flexplate, (thanks Ford for that genius idea) and back on the dowel pins of the motor, and got some bolts started. I wear the scar on my chin to this day and I'm 61. I went on to become an owner operator of an automatic transmission repair shop. Never worked on my back again. You couldn't have picked a better transmission to start with for your young friend than those old torqueflite 727s and 904s. Easiest trans of all.
I can relate to that story in so many ways!
@@UncleTonysGarage LOL.The worst part of it is that after all that grief and bloodshed, I had failed to fix it. You can bet that after that experience I was much more diligent about answering the question, how exactly do you rebuild an automatic transmission? 🤣
That was an excellent tutorial, Uncle Tony. I used the in-engine method to find out what cam I had. It is too bad that a lot of cam companies don't make their cam cards available. It would make life easier. I should have paid more attention in math class.
I put a dark green DC purple shaft in a 318 recently, it sounds fantastic and goes really hard.
We found others with colours only DC cams
Red is .557
Orange is .590 and that's all we found
318 is a junk engine. How much beer did it take to start it ?
@@jesse75 I love 318s been running 13s with low compression run of the mill 318s for decades. 14s with standard 318 heads and 2.92 gears. I have a lot fun that's the only thing that matters.
@@benmopar 318 is an interesting engine. In it's own league.
Thanks for not getting offended when I flipped you some sh!t.
Shows you have some class and are mature. Peace brother.
@@jesse75 totally cool I love them, it's just a passion, I keep playing with 318s where I can, always thinking about improvements.
@@benmopar what single thing I believe the 318 has going for it is rod length.
Just the opposite, and I'm more strictly a Ford engine person, is the 302/5 liter has too short of a rod.
If I put a 5.4 inch rod in a 302, there's a big improvement.
It was popular back in the day, before all the stroker kits, to offset grind a Windsor Crank and use 318 rods.
It really woke up that engine.
After market Chevy rods can have nearly the same length as a 318.
Because a longer rod in a Chevy works better too.
I've only rebuilt one 318. It was years ago. Was in a 1974 4 door dodge dart. Yipe. Old lady car.
Another engine with a long rod was the 216 Chevy six. That engine was a stomp puller and got over 25 miles per gallon.
318 is an acquired taste. I think redheads are just, well ugly and weird. But some guys like them.
318 is like that to me.
If you lived near me and I came across a 318 or 360, I call you up and say come and get this thing. Peace brother.
I dislike the motor mounts on a dodge. One reason I don't do more of them.
Ford's are really easy.
Great knowledge sharing uncle Tony and Always Love that you share more n more Mopar tricks and Experience. Thank you .
We used to call it a Hemi grind. I got them wholesale for $36
My swap meet mystery cam was a new Manley Mauler BB mopar cam from the '60s that has .447 intake lift.
Ha! I was just measuring mystery Alfa Romeo v6 cams yesterday. made a bench jig to do it with a dial indicator and a degree wheel to figure out LSA. I found a couple sets that are not in the books.
I love your videos man, I wish I could come apprentice you and learn your old-school hotrod tricks. I've been tinkering with stuff since I was a kid as a therapy and haven't stopped since in the past 13yrs. Great videos and information. Keep it up!
That's a decent cam I ran it a few times back in the day. Once in a 318 and once in a 340 a good all around cam that was easy to drive on the street without a lot of other mods.
How did it go with the 340? I got the same cam new old stock part im planing for my 340 which is a 68 block 10.5.1 comp and will be using J heads with larger 2 02 valves and adjustable lifters. Should be a neat combo
@@67wogval It's a good mid range cam. It'll move your torque peak up a few hundred rpm and still pull well down low. My old '70 340 auto liked it
I pulled a sbm 727 and replaced it with a 904 in the dead of winter while having the flue. It took me the better part of 2 days.
Everyone always thinks a job will take 10 minutes. There's always unforseen things that happen or come up that makes it take much much longer.
If u think it’ll take an hour
It takes a day
Think it takes a day
It takes a week
Uncle Tony taught me that 😂
So, here’s another possibility… get a good pair of heavy, accurate vee-blocks, set the cam journals in the vees, and use a dial indicator on a mag base to trace the cam profile as you rotate the cam. Might save a bit of time over sneaking the cam in and out of the block. Just a thought.
shoot, i thought that WAS his recommendation before i watched the vid. that's how we used to do things.
I have the engine block but I don't have vee-blocks.
Good tip! Grizzly sells a pair of 4" [cast iron] for twenty bucks. Easier than keeping an old block around - and handy for many other things too. Hit em with sp350 or some such when not in use, wrap them up and should get a lifetime of use.
@@flinch622 now that you say it, there's a company P-something that makes fake plastic engine blocks for shops who fabricate frames and need a dummy engine to figure out where to locate a firewall etc. otherwise, the only benefit of a spare block is if you know a great welder and break a similar block--you can have a replacement cut off and welded on.
My diesel teacher had a big sign in shop "slow down to speed up" He did an awesome job!
Amen Tony I wish the kid the best of luck!
This is great stuff. You're a good teacher. From Ohio
Well hell! The next time I Need this job done I'll call ol' 18 minute hot dog boy and then I'll stand there with a stopwatch!
Have torch, will travel.
(but you might need either a new car or new transmission once I hot wrench it out of there)
Thank you, sir, very helpful.
Youre a good dude uncle Tony!
Awesome video thank you
He did really well. Well done
Degree wheel and the dial indicator will really give you the most accurate information, duration, lift,& overlap, then all that on a graph, find the power!!!!!
Digging the Satellite a lot. Just a small thing- get a drop down indicator that either fits into the valley nicely or has a longer probe so that the probe's axis is in line with the 'Z' axis (up and down) of the lifter. Don't have it on an angle different than that of the lifter, for an accurate measurement. I know why Tony's indicator is set up that way, and I know he'd usally do it a little differently. Just saying, for the casual observer, that yes the error introduced is minor in the application here but you don't need it at all.
Hang in there, Josh. Don’t pay attention to those critics.
Glad you were there to teach the art of American V-8s.
Good info uncle T
HOWdy U-T-G,
the BUMP & GRIND of CAMSHAFTS
Thanks
COOP
...
Helpful video
Can you do a video on how to split atoms with an expensive dial indicator?
Wow, what a wimp, I could've had that trans out in three months with nothing more than 100,000 dollars worth of Snap On tools, a lift and three helpers!
( street hemi ) purple shaft 474 small block .
I believe that grind , was revised in 1984 , with change to duration ramp
Thank you for the good information! I have a 1969 351W someone built several years ago. I’m now trying to determine how it was built and what’s the cam size. So your video is perfect!
Question: my hydraulic lifters are not oil primed, I assume that’s ok to get a measurement because the lifter spring most likely won’t compress while measuring the height like you did. Correct?
Hope my question isn’t confusing
Fantastic
King content. :)
In what universe does a brand new dad have three minutes to himself?
So awesome you are mentoring these young guys. Very cool to see several simultaneous projects in the shop. Bravo Uncle Tony! One thing though, at 10:12 your dial indicator is not dead nuts parallel to the lifter bore axis, that causes inaccuracies, and here a few thousands could make a difference. If you're off-axis by 8 degrees (which you appear to be, at minimum), that will shorten your measurement 1%. 11 degrees off and you come up 2% short. 15 degrees is 3.4% short, 20 degrees is 6% short. Non-linear, it adds up quickly. Percent error is (1-cosine (angle)). Trigonometry rules, as does UTG!
Uncle Tony I get so angry when guys out there talk shit about a guy trying to learn his way around a car. Instead of putting him down and making his plight worse, help the guy out. We all love cars here because we are watching this video. Help grow our love of cars with encouragement to these young men. Rant over
Thanks Tony this was great. How can you tell what engine manufacturer a cam goes with? I mean a mopar versus ford versus GM etc etc etc. appreciate it.
The simplist way to check overall lobe height is put the cam in a lathe between centers. This of course is provided you have access to a lathe 🙄 this will also allow you to check the cam bearing run out. Cam are found between centers. In the old days many moons ago the cam lobes were ground using a master cam. Today it's all CNC
And if you are going to use dial indicators. They give the most accurate reading if the axis of the indicator is 90°s to the diameter or surface being checked. And instead of using a mag base make up a set of posts that screw into the various tapped holes.
I like putting the exhaust and rocker covers back. I’m just that way.
Very Important. I have one Lunati Bracket Master solid that has the grind stamped, but they dropped it from the catalog, measuring is the only way.
This is awesome knowledge brother. And Josh is doing a incredible 👏 it's alot of work.
Those Purple Stripe cams were very good IMHO. Ran one in my 383 many moons ago.
Melling 1334 is a great cam for the magnum. With my rockers I'm measuring.453
that was some good teaching right there but without the internet it would be a lot of waiting for catalouges to arrive lol
What if you held the cam against a pane of glass and measured up to the "heel" or base circle, then measure to the "toe" or cam top, subtract the difference and you have your lift ??
I used to think nothing of yanking transmissions, vehicle on jackstands, transmission on my chest, in many cases. Got pretty good at it actually, if I don't say so.
Today, it's one of my least favorite jobs, lol.
Camshafts should be clearly marked in a way it doesn't need to be removed (just remove the chain sprocket) to know the number.
I haven't ever found a part number on one.
If you don’t know the manufacturer,measure an exhaust lobe too, helps narrow down the search because a lot of manufacturers have different exhaust and intake lifts.
Hey Uncle Tony I got a pile of messed up old Dodge trucks from like 65 69 73 all short wheel base and the odd long box but you know having a mentor helping in fellows like what you're doing for this young fell after you'll oh I can't remember what it's called down sorry much love and respect
Cam IDs and specs are still the most closely guarded secrets of performance builders, just like in the prehistoric days before the internet turned everyone into a professional. They don't want anyone copying their cams that they worked and tested for so long, to find the one that works best. When I get a cam for a build, I always get the build specs from the grinder, and give it to the purchaser. I grind any numbers off of them, an just put my code on it, where I know where it is. They will have to mic it out if anyone gets it that isn't the original purchaser.
really great stuff, tony. thanks!
Good tip. Thanks Tony.
I’m a car Detailer retired but there were some cars through them they took too long but also I’m a little bit more about mechanics do some jobs or that way so I understand your friend and you just got a power through it so you may not like them doing the job
❤❤❤❤work is in the air and in the blood ❤❤❤❤
Even with iron exh that should be a fun cruiser. Quieter too. If that's what he wants fine. His car. His choices
. . . . And then there is the Degrees to consider FUN STUFF Uncle Tony, we did it with paper, pencils, & sometimes a Cam degree tool, but the notch or keyway work as good base line zeros :) 😎🏁🇺🇸🎸
In the 80s I had a flat cam on a 318 aspen went to the machine shop they gave me a cam worked perfect no break in no special oil and minimal skill and knowledge on my part car ran great after that . Now I’m more confused the more I have learned 30 years later
Valuable wisdom UT. Thanks man.
Old guys rule. 😎👍
Comment, no hate.
It may be the 0.484 lift cam. You had a bit of excessive angle on the dial plunger to the lifter bore centerline. Ive been bit by this verifying a cam card.
Enjoy your tubes.
I beleive that you were measuring the lift of an intake lobe (at least that is what you said at 9.25), but you looked up exhaust values in the data sheet. However, I still understand how to do it.
That has got to be some of the most useful info you have ever passed along.
How do you know what cam company to reference with?
Question....
I've installed and successfully broken in several flat tappet cams, both solid and hydraulic without using light springs for the break in.
Today it seems like many are doing this and I'm wondering if it's due to all the flat tappet problems in the last few years.
I have a Howards solid flat tappet circle track cam and Howards lifters I'm ready to install and would of course like to not do all the extra work of break in springs...
Not a huge cam, only .530 lift/240° duration and springs are 330 pounds per inch
What say you?
Hey Uncle Tony, can you use a used cam with new lifters? Or do you have to have the old lifters that were broken into that cam?
Yeah that's fine
What’s the largest cam duration you can put in a stock Chrysler 383?
Good question. With stock springs I'm assuming.
How do you know if hyd or Sld?
Uncle Tony did you ever drink beer with Roy Demeo?
"I could of done that job in 18 minutes with a mouth full of hot dogs."Good fer you!🤣🤣🤣🤣
I had to do this on a pontiac 400. Had some oddball solid lifter cam in it. It was a GM grind for sure but the closest I could find was the ram air IV cam and that wasn't exactly close either. Nothing in some old crane and comp books either. It was suggested it was either a prototype cam from GM or a regrind. Thing sounded like it was ready to party, very rowdy bump stick. The one I replaced it with even though it was a roller, sounds tamer despite more duration and lift... go figure.
“Ready to party and very rowdy”
And u TOOK IT OUT 😢
Why?
@@fastinradfordable 3 flat lobes that ended up causing the engine to need a refresh... one cold start it sounded great then about 2 minutes later I said: "well that don't sound right." Definitely makes more power now though.
not surprised the roller is tamer, as its probably accelerating the valves to full lift faster so it won't need as much overlap. but be careful on a non super duty pontiac block, the lifter bores can be snapped off with too radical a cam lobe.
@@albertgaspar627 it's an XX block, we're good there. But yeah... the at .050 duration is quite a bit more, seat to seat is the same. The LSA is a bit wider which probably accounts for the difference.
@@fastinradfordable no wonder it sounded rowdy . it had 3 flat lobes.
I'm having a hard time putting on this timing belt on this V6 Honda 3.0. I got the belt on correctly spun the crank one time and then had somebody stop by. So I took a break and then went back to work on it after they left. I saw that the marks on both cam sprockets were pointing down because I only rotated the crank once but didn't realize it at the time because my mother had just died and I'm still not thinking clearly. So I took the bill of the rear cam sprocket and rotated the cam clockwise I think and it's spun on me because I used a ratchet instead of a wrench. I wasn't thinking clearly. So then I reversed the ratchet flipped it back and called it a day. So then thinking about it overnight I went out and lined up the sprockets put the belt on and rotated it one more time on the crank which put all the pointers lined up. Question is if the rear cam is out say one revolution in either direction would I still be able to rotate the engine with the belt on? Thanks in advance
2 seconds into the video and I hope this will help me. Bought a 65 Mustang that runs like a bat out of hell and has some suspicious parts. The 9 quart oil pan, and $500 harmonic balancer scream to me stroker. The block is a 302 out of a 71 Torino but it has the 65 heads from a 289 which are high compression with that combination. The cams in mystery and and hopefully this video will help me figure out what I've got. You can check out my channel to hear the car idling and see it testing the traction LOL
How do you know the block is out of a Torino ?
I have a 383 that I’m collecting parts for and if Josh wants to move the valve covers he’s taking off his satellite, I’ll buy them
Great tip as usual Tony 😎
Headers are a pain the A*s on B Bodys. I owned a 1969 Superbee and fortunately for me had a A 833 4 speed not a torqueflight. A torqueflight being fatter would be even harder to fit.
A little better camera focus on the INTAKE LIFT part of the chart would have helped because the EXHAUST LIFT was the same number. (Confusing but I got it!).... 😕
Great info👍 what about duration? Or does a certain amount of lift correspond with a certain amount of duration?
Congratulations Josh! That's not an easy job, but removing and reinstalling 727's gets easier every time you do it. You first reinstall is gonna be a bitch.
👍
OK so what is it in the video "Plus The Myth Of The Purple Cam" form Nov 15th 2021 you stated there is no such thing as a purple cam and now your saying you have a purple cam for this engine now I'm confused???
I feel his pain, I only get a couple hours a few nights a week.
So to pull an engine it might take a week or 2.
7-28hr to pull engine?!?
Just yankin yet chain😂
thank you
Wow, people really talked smack like that? I think they are missing the point of this show. We are all merely students, Tony is the master.
And we are lucky to be here.