Dolby Atmos Setup | Denon AVR Setup | Amp Assignments
Vložit
- čas přidán 23. 05. 2017
- Another Dolby Atmos Setup video! How to properly setup your AVR to show that you have Atmos or Height channels connected. Watch this video and find out! Check out my recommended Atmos speakers at my Amazon Store: www.amazon.com/shop/technodad
Discounted Denon AVRs: amzn.to/2NfNtXs
Discounted Marantz AVRs: amzn.to/2BFYNYb
7-Channel AVRs: amzn.to/2DmnMBt
9-Channel AVRs: amzn.to/2PVf2Jl
4K HDMI Cables: amzn.to/2QCi3LW
Budget Range 4K TVs: amzn.to/2JLaf7X
Mid-Range 4K TVs: amzn.to/2zEqdfA
Premium 4K TVs: amzn.to/2qxoRPx
OLED 4K TVs: amzn.to/2R9DRC5
Sony 4K TVs: amzn.to/2QM5YqR
B&O Headphones: amzn.to/2RulKDG
Recommended Soundbars: amzn.to/2SVutDV
DISCLAIMER: This video and description contains affiliate links. As an Amazon Associate I earn from qualifying purchases.
Check out my recommended Home Theater setups: Kit.com/TechnoDad
Equipment used to film and edit:
iPhone 7+
iPad Pro
Osmo Mobile: www.amazon.com/gp/product/B01...
Final Cut Pro X
iMac 5K Late 2015
MacBook Pro 9,1 Mid 2012
Thank you for watching!
Don't forget to like and subscribe!
Follow me on Twitter: bit.ly/TD5TWTR
Follow me on Facebook: bit.ly/TD5FBP - Věda a technologie
Exactly the video I needed, thank you so much! Helps me make decisions on how what to buy for my new home theater room.
I just found this video. Dude, You did a BAD ASS wiring job! Those ends look amazing! I don't know if you'll see this, but I wanted to say thanks for the video!
Hi! I love those braided cables!! I'm glad you found the video helpful!
EXCELLENT video presentation. This man covers it All. I have the 7.2 Denon
and yes, there is a lot to work with and I'm not too familiar with receivers today. This is just what I needed,
Thanks for sharing your time and knowledge.
Thank you. I finally figured it out. My surround back speakers I could never make them work until I watched your video. Thank you very much. 👍
I need to check my set up today after watching this.Great informative video.
Another great video! Please keep them coming.
Thanks man.. really help for a newbie like myself. 🤙
Thank you so much for this video, You are so clear and Informative in all the steps to take to set up the speakers correctly. I have just purchased a Denon AVR-X3600H. I am driving Jamo 809 floorstanding with a center and 2 surround speakers and 2 dolby atmos upward firing front speakers. I really think your video will help. :)
Hi! Glad you found the video! I just got the X3600H and will be making a video about it as well.
This is the setup I’m looking at, how is it working?
Excellent video! Thanks! I'll try to get my setup working and I'll probably be back with a question or two. Again this video is very clear and I didn't have to pause once. :) It's not a rush job,
Sounds like a plan!
Hello Great Channel. My Denon also shows a Screen for measuring the Distance from Front Atmos speaker to the ceiling.
Video very helpful, thanks again TechnoDad!
When I move into a house or even a better apartment, I'll do the 5.1.2 Dolby Atmos/DTS:X setup, but until then I only got enough space for a 5.1 setup for now.
Hi, thanks!! Yeah, it's tough sometimes! I can only fit 5.1.2 in my living room. I would love to add 2 more Atmos speakers. Not sure if I can though. Oh well!
Great video, and after watching this video, I decided to return my Sony str-dn1080, and go with denon avr-x4300h, denon receiver are easier to use and the sound quality is better, since this is is a 9.2 receiver, now i'm getting 4 ceiling speakers for atmos, thank you for this video it was really helpful .
+neker rivera Hey! Nice man! I can't wait to get 5.1.4 up and running!! I'm looking into getting those SVS Prime elevation speakers. They have a cool wall mounting system and a 70 degree angled front baffle.
Techno Dad, I have 4 Bose 161 for atmos, they don't sound as good as svs, but they do their job, svs elevation speakers were out of my price range, $199 per speakers ouch, but definitely the denon is top notch what a difference in sound quality.
look forward to that many thanks
Thanks man it was very helpfull, it's hard to find infos like this on dolby atmos
You’re welcome!! Thank you for watching!!
@@TechnoDad
Hi i want to know is it possible to connect 4 ceiling speakers in 7.1.2 avr.
Like parallel or series connection.
Please help
Great channel. Love from India
Thank you!
Good job..i enjoy your videos. Thanks!
+SPD Music Productions Thanks for watching!!
Hi, just a question, I want to buy Denon x1200W, I have 6ohm speaker overall but 2 old 8ohm speaker as front LR, can it work? It say from 6 to 16ohm impedance but what about differente value together, are the amps totally indendent per channel about impedance? Thanks
Very helpful!
Hey! Thanks for yet another informative video. I have one question, is it worth having Bose speakers set up for Dolby Atmos along with a Denon receiver?
Great Video😎
hi. i just bought the denon avr-s950h receiver 7.2 channel 2019. i bought it new from best buy. when turning the receiver on or off, it sounds loud like the amp has 1,500 watts, or a loud click. works fine. ever heard this from denon or others. should i be worried if this was you. $500 door stop.
Great information. Thank you
Thanks, you make it very simple for people like me excellent vdo 👍
Most welcome 😊
very good demo thank you so much
+davo You're welcome Davo!
Ok just asking as i am going to buy the Marantz 8802A Pre/Pro as on my AVPa1hd i ran Audyssey and then just checked my speaker settings afterwards but i had nothing hooked up to my height channels on that unit.I just thought that when Audyssey is running it automatically detects the height channels as it does every other speaker.I run the Audyssey pro kit so it might be different to the standard.Thanks for that info as i will look out for the amp assign when i get my new machine.
Nice vid. I'll just add that I just got a denon 2300x which is a 5.2.2 atmos capable (or plain 7.2) and on boot up for the very first time it walked you thru every set up of hooking the speakers up and assigning the amp to your height speakers to running audyssy. It was pretty slick and impressive.
Also I picked up roger waters the wall blu ray this week since I read It was a great atmos track and they were right. The entire thing blew me away. From audio to visuals. If you like The Wall at all from Pink Floyd it's worth a buy. (There are some melodramatic interludes with roger waters but they do go with the flow).
+oletheos I wonder why mine didn't do that on first startup. Anyway, I saw Roger Waters perform Dark Side of the Moon at the Hollywood Bowl, and that was awesome!!! Thanks for the tip about The Wall, I'll look into that! I heard the SACD of Dark Side is pretty awesome because it has a 5.1 soundtrack.
great tutorial. thanks.
Eddy Mathieu Thanks for watching!!
Great video!! I have a couple of questions. Here is my setup:
Denon 4700
Klipsch R-625FA Dolby Atmos Floor stand speakers
Klipsch RP- 504C II center channel
Klipsch R-41M Bookshelf speakers
Klipsch R-12SW subwoofer
1-What are your suggestions for the crossover settings?
2- What are your suggestions for the db level for all the speakers? This is where I am confused.
Awesome video, thanks for sharing
You're very welcome!
Hello, i have a question! If i put on a Denon AVR the sound mode to stereo for listening music will the subwoofer turned off? If yes my main front left and right speakers will handle all the frequency they can handle or they will remain crossover and run at what they were set up when running with a sub?
Good job on this video!
Thanks! Here's the newest Denon AVR setup video - czcams.com/video/LXRXSZ_W9c0/video.html
Can you do a video showing the setup menu for the 11.2 Yamaha receivers?
Hello Great Vids. Any links on settings up a Denon AVR-X3300W for Atmos?
On a Denon s750h AVR can i connect 7 speakers of 1 sub., 2 front.,2 surround.,2 surround back and 2ceiling for atmos???
My receiver can only do 7.2. What is a better surround setup - FH/FW or SB?
Nice vid! I have a 7.2.2 setup with my X4300h and love it. What I did differently was set my crossover to 80hz for all of my speakers per the suggestion from Audioholics. Anxious to see what surrounds you get and if you're going for an additional amp.
Hi Dennis! I have had my crossover at 80 for all my speakers as well, that's the THX standard. I may go back to that, but I'm not sure. I will be receiving the Klipsch RP-250S today and making a video on the difference between monopole (bookshelf) and bipole (RP-250S) for surround sound speakers. I actually just spoke with the people at Emotiva about adding an amp to my setup. They say most people upgrade the amps for the front sound stage and let their AVR handle surrounds and Atmos speakers. I sent him the speaker models RP-280Fs and RP-250C and he said they are pretty hefty speakers and I could use a 3 channel version of the XPA Gen3 which would output 275 Watts RMS per channel. I thought that was a bit much, but he said it would drastically change the sound and punch in my system. On the other hand, people in the Klipsch group on Facebook, they recommend adding a second sub before I add an amp. So I'm more confused now! Hahaha!
@@TechnoDad
Does adding adding an Amp to a Powerful AVR (e.g. X6700H) improve Sound Quality even at Low Volumes?
Hi!! I'm happy with this channel of yours👍 i have a question for you...it's possible to virtualize the front and rear sound with the Denon avc x 4700h if you don t have an atmos configuration available? Thanks!👍
Love DENON components
I've a Denon X2400H. I was curious if I connect another AVR via Zone 2 can I increase the amount of speakers connecting both receivers via zone 2? So I can have 7.1.4 for example?
Awesone 👍
QQ - great video btw. My front speakers are connected to a separate amplifier - I use the Front L and R Preamp out , directly into the Inputs on the Amp (2 ch Crown - 330w/4ohm to each side - powering Polk Audio LSI25's). For some reason, no matter which Amp Assign I select, I keep getting MONO out of the preamps? I can tell because when I run test tones, When Front L is highlighted, Im getting sound from both front speakers. Ive double checked many times, everything is connected correctly. Also it seems that the terminal config never even highlights the preamp section as an "active" pre out. My guess is AMP assign needs to be changed to utilize those preamps. I think its treating it as a line out right now. I dont have any "theater bypass" inputs on this amp either. My previous AVR was a Denon AVR3805 - this handled the left and right preouts perfectly. Obviously things have changed a lot over the years. I have been trying to get this to work for the last month to no avail. Any ideas?
Hey tech (D). I don’t fully understand the crossover setup.have you made a video for that Specifically? Thanks bud. Joe l
very helpful
Can you help me with the manual equalizer, I don't know anything about EQ and would like to know any suggestions on how you have it. I have it by default but as I said I don't know about htz. Thanks
I just installed a pair of Martin Logan Vanquish ceiling speakers for atmos speakers. I use a Denon AVR-S930H, I used the Audessy eq and for some reason I can’t get a whole lot of sound out of the ceiling speakers. Any tips??
Harman Kardon BDS 885s specification and Denon AVR which one is the best
Hi. Great video. I just bought the Denon AVRX4700H. In the manual I don't see a connection configuration that will represent the speakers I have to connect to it. There will 5 floor speakers (FR, FL, C, SR, SL, plus 2 Dolby enabled FHR, FHL (assume connect to Height 1) but I also want to Bi-Amp the Front Klipsch 8060's, and would likely use the Height 2 connections for that. They have 7.1 channel:Bi-Amp Connection of Front Speakers in the manual, but in that configuration they show an SBR and SBL which I do not have. When I hook up all the speaker wires and run Audyssey, will it figure out the correct configuration to ASSIGN? Thank you in advance for any replies.
Hi great video question please if you don’t mind. I just finished setting up my home theater and I’m first running a Sony A90J 65 inch OLED, my question is I’m using a Denon 3700h receiver with two Klipsch RP-800F’S front speakers and two R-41sa’s as the height speakers which are mounted to the wall on each side of the tv cause I didn’t like when you place them on top of the floor speakers and aim it at the ceiling to get the overhead affect. I also have two Klipsch RP-600m bookshelf speakers on stands as the rear and I’m using the tv as the center channel until I get dedicated center speaker, there is a 10 inch woofer as well. Now the entire setup uses hard wired connections and I just bought two Denon 150 home wireless speakers and I would like to use them as rear height speakers to make it a 7.1 but so far I’m not seeing a way in the Denon setup to add two wireless speakers it only gives options for connecting more wired speakers. So is it possible to do this? Thank you so much
Do you find any advantage with having high frequencies speakers in the top channel? A lot of in ceiling speakers I have seen can go to 50hz.
Yeah BirdMan, there isn't a lot of stuff going on in the Atmos channels. I keep mine crossed over around 100Hz.
Techno D hi,
I have an AVR 2400H where the HDMI socket for cbl does transmit the actual cbl audio, but not video in the Samsung 55" SMART HD TV (TV is not 4K). Tried to exchange cables and cbl box, tried reset, nothing helps. Any suggestions as for the denon sutup? The TV setup?
Appreciate much your help.
OFER
I have a Denon AVR X2600H I cannot find what I need online and i love your channel! I used to have an old Yamaha AVR that I used pre-outs to a stereo amp that I used for my front left and right. I wopuld like to do this again if possible.. Does this Denon amp support this facility as it doesn't seem to be working. I appreciate any advice you can offer. many thanks
Your review are very insightful.Thank you!!!
My question is :
1. How is Onkyo SKS-HT993THX and how would it be for an apartment?
2. Which among these two Amp the above mentioned system will be good - Onkyo TX-NR686 or Denon AVR-X1500H?
I like the Denon X1500H AVR over the other equipment you listed.
The speakers I'm using for dobly atmos is the SVS prime elavation speakers 2 on the front wall and 2 on the rear wall and 2 svs PB1000
Assign mold should you leave it on 11.2
On Denon 6700 what preamp setting should I use so I can connect 7 floor speakers to amps and use the AVR for only atmos speakers? Please let me know. Thanks
Although I have the pioneer elite, thank you for this video. I had my height 2 speakers set to back since they were as far back as they could go but my sitting area is also right under them. I don't know if mcacc auto calibration just would adjust the sound but it's good to understand how to set them up correctly.
+Michael Hinchey Hi! I'm glad you found it helpful! If I were to have ceiling speakers right above me, I would set them to "Top Middle" in the Denon software. But like you said, the AVR will figure it out. Thanks for watching!!
Does the Denon 3700h have the ability to run dual front L and R speakers and 6 atmos channels in the speaker configuration?
The way my movie room is set up doesn’t allow me to have rear surrounds or rear side surrounds.
I know it’s capable of processing 11 channels, just didn’t know if you were only limited to placing your speakers only in areas limited by the receivers speaker configuration set up menu.
Thanks
Where did you get the HDMI cables and wires and types for this model? I like the clean set up.
Hello Channa, if you bi-amp your front speakers, do you still set your front speakers to small?
I cant understand how i can set my X3700H front left and right speakers to work with external amp. I plugged preouts to Hegel and front speakers connected to also Hegel left and right. I can play directly from hegel but i cant use denon 5.12 setup with my fronts. What amp option i have to choose to make it work then? I dont see option to use left and right as preout only full preout for all speakers??
Can you set individual impedance per channel? Thanks
I hv a 5.1.2 setup.2 top tear not dolby enabld.i m using denon x4500h nd dont hv zone 2/3 spkrs nd dont intend to.which amp assign i will use- 7 chnl+zone2/3 or 9 channel assignment.one more thing if i could use my top rear spkr set up as dolby surround,would there b any prob?
Wsup u know I'm going with the Pioneer sc lx901 and my setup will be 7.2.4 my question is how I set it up with the pioneer
Hi Mate, i have Bose accustimass 10 series 5 speakers set at 40 hz, i have atmos ceiling speakers Yamaha Is Nc 600 set at 60 hz and Lfe set at 120 hz that was set up automatically by mic on onkyo Tx nr646, i just want to know if that is the correct settin to get best atmos sound. Really appreciate your help.
Tried connecting my apple 4k tv to the same brand reciver. However I cant get it to decode atmos at all. The reciver even says it supports atmos. But cant get atmos support in the movie room. Tried auto selection it on apple 4k tv and it only supports 5.1 connected it to the DVD HDMI thing. Yet it works with my samsung soundbar Q70R. Any help?
Hi I have a denon 2800h running a 5.1.2 I have mounted 2 Dolby Atmos speakers behind my seating area on the wall just near the ceiling as I couldn't fit any ceiling speakers due to not having a flat ceiling my question is in the denon settings there is nothing were I can tell it about the rear wall mounted Dolby Atmos speakers placement
Techno dad thanks for honoring my video request. Great job explaining how to set up the AVR with Atmos it really helps since I just got a Yamaha RX-V681 to run a 5.2.2 set up. One thing do you use the ARC feature on your receiver? If so does it work well?
Henry Sermeno No problem! I don't use the ARC, I use optical out from the TV to my Denon AVR. I've read that ARC has some strange issues, but I have not tried it out.
Henry Sermeno So I tried using the ARC and it works just fine. There was a little tinkering around I had to do to get it to work correctly. Once I had it setup right it worked like a charm!
Nice One TD 👍👏👍👏👍👏👍👏👍!!!
Thanks!
I am using DENON X1200W ...need some guidance....When i set to Dolby digital ...no sound is coming out of Back surround channel(L&R)
., only settings @ Dolby surr and MULT stereo ch can i hear the sounds from Back Surround channel L&R
Hi sir I have a Denon X1200W…
When I set to Dolby digital, there is no sound at channel SURROUND BACK L &R.
Mode Dolby surround and multi channel was fine.
Why is it so ?
Do you have your system set on lfe or lfe +main
sweet....I'm guess you're ganna get Logan in 4k, can't wait for that review
+Andre Blackwell I got it yesterday, watched it last night in the bedroom. Great film!! I need to watch it on my OLED though...
Please help i have spent quite a bit and i dont understand. I have a denon X1700h that is 8ohms and i have 2 6ohms speakers. My 1 year old removed a binding post from 1 speaker so i have only been using 1 speaker. Today i got flashing red light and i have removed all wires and its been off for a few hours but still got red flashing light. It is still under guarantee so i can return but would you know why this could happen and if i can get an amp for this reciever ? Because i want to get 4ohm speakers
Do you have any idea how to get MacOS's "Audio MIDI Setup" to recognize all 13 channels and send audio to them?? It seems stuck at 7.1 or 5.1.2 MAXIMUM. My Odroid sends Atmos to the Denon AVR Just Fine By Default.
hy there ,techno dad I have a problem with my denos , I make the audissey setup and almost all the speakers ,the receiver turned off only left the front, what I making wrong...
Can I use powered speakers as atmos speakers in a 1600h using the preout?
I have a question. My current setup is front dolby 5.1.2 However I don't understand the proper setup for front dolby R and front dolby L.
What should my source level be set at ? Nice video
Hello, I always follow your channel ... you are like an encyclopedia of technology ... always with answers to my questions ...
my questions is I have a marantz Av 7705 (preamp) + a monolith 11X amp .. when you choose in denon the Dolby S function, that function does not appear to me in the marantz AV 7705 only 4 channel high.. not like your denon says hight, dolby s minute 4:06 ..in marantz the high speakers work as atmos? why on the screen of AV 7705 it says Dolby Atmos ,, but the immersive sound is not felt, nor detailed ..? I have a 7.2.4 klipsch system ... please wait for your answer..thanks
i purchased 4 front speakers. i’m having a problem with putting the 2 independent if that makes sense
I have a Denon x4300h how do I set up to 11.2 channel. Mine only have 9.2. I have an extra two channel amp Buy don’t know how to connect it to my receiver. Thanks
Hi! I just made a video about doing that. So watch this video, but you'll be needing to locate the height 2 left and right outputs. czcams.com/video/IhSKFXgBO8Y/video.html
Really great video... just wish you'd explain the crossover settings more. Not sure I understand why / how those numbers need to be adjusted.
Look at your speaker specifications. If they can go from day 60 Hz up then set the crossovers 10 to 20Hz higher. This will then push the lower frequencies away from those speakers to your sub, meaning less distortion and more accurate sound. I'd uncertain, set all to 80Hz
MURANTZ Zone 2 Set-Up -- need to know how to setup zone 2 -- not receiving sound from zone 2 speakers -- when switching to zone 2 my front 2 speakers have sound but no sound is coming from 2 outside speakers. I only want zone 2 for my outside speakers -- thanks.
Sir can I connect my Panasonic Bi Amp speakers with Denon 7.2 dolby atmos AVR?
Thank you for your awesome videos! I can't decide between Denon X2500H or Marantz SR5013?
Hi! That's a tough one. You'll have more flexibility with the Marantz...
hi im currently running a 5.1.4 set up with a dennon avr 4500 amp and I've ran the audssey app but am so confused about all the settings and how to adjust them ? its a minefield of info and I wondered if I send my calibration details to someone the would be kind enough to have a look and help me please
Can I use a denon avr-s910w as 5.1.2?
I just bought atmos speakers and a new amp with atmos. So hopefully this will help me.
Nice! Email me if you need more details on setup: technodad55 at gmail
Great video! 2 questions, should I get the Denon home cinema sound bar set and the LG OLEDC7p (which has standard built in speakers) or get the LG OLEDE7p (which has the Dolby sound bar built one) and get a receiver later with good speakers? If so, which system you suggest?
+Rodney Johnson Hi! I have the LG E6 from last year, and I still use my surround sound system. The built in one is good but once my wife starts cooking, you can't hear all that well. I always suggest to get a good soundbar or step up into a surround sound system. If space is an issue try out some soundbars. Also, the price difference in the C7 and E7 is significant. Check out this Klipsch RSB-11: www.amazon.com/gp/product/B01LR8Y1TO/ref=as_li_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B01LR8Y1TO&linkCode=as2&tag=tec0ab-20&linkId=fc0e56f0606cf45acc452aa2d98a9b61
I have dolby atmos speakers that are 2 spare tannoy has xp satellite speakers pointing down in the corners of my room.
But when netflix is playing a dolby atmos series it's not showing dolby atmos on the 2700h avr
Hi, I have a Denon Pro dn 500 av preamp, impossible to get acces to HDMI imputs no sound, I connect a Notebook I define Denon but no sound appear. Can you help me Dad?
Can you set it up for 7.1.4 and set the 4 atmos to middle and front? I don't really have room for rear atmos sense my seating position is only a foot off the rear wall.
I have the same question too
is there a diffenece if you do 9.1 or 11.1 assign if your running a 5.1.4
Another great video! Do you actually leave Dynamic EQ on with reference or do you disable all those settings?
Louis Hernandez Hi Louis! Sorry about the delayed response. I do have the Dynamic EQ on with the reference setting.
Hi techno dad,, pls i need your advice,, i have the denon 6400 and im runing 7.1, front and center are : defintive tech b9060,,and def.tech dolby surround a90 and the surround also def.tech 9040, and subwoofer harman kardon, i seted up my conf,as 11.1 so all the 11 amps be in my main zone,,i turned off zone2 and 3 coz i dont need them, but here is my question, b4 i ran the auddesey and my conf speakers for def for main and center are LARGE. the surround and dolby atmos front surround are small..after the audesey finished it turned my main and center to small! So why if you have any idea my friend,, and 1 more thing,, before i include the harman kardon sub,, i made a audesey onky formthe def.tech speakers and it seted it up as large for main and center,,and i was running the inter sub in the def.tech without conntectingnit to my avr,,but once i changed thr config to 1 spkr harmon it turend my speakers small,,and for the cross over i made it all 80 hz,,so is 80 for all ofmthem as small speakers ok or is it wrong and might effect my speakers,,also why do you think auddesey consider the main and center as small not large?
Thank you and pls forgive me for any mistakes
Hi just watched your video great information I followed your steps about amp assign on my denon avr x4300h once I set mine to a set of 4 up firing Dolby atmos speakers I set the crossovers then went onto distances and noticed it says Dolby speaker setup I clicked that and then you have to measure the distance between the top of the up firing speaker and the ceiling
Then I did the audyssey calibration and after that checked to make sure none of the settings had changed after doing all this the overall sound including atmos is a lot better
I thought you could put this on your CZcams channel as it may help someone
+Robert Adlem Hi Robert! Thank you for sharing your experience with the up-firing Atmos modules. As I don't have them, I can't comment. I always say it's good to do an calibration whenever you change Speakers or locations. I'll put that in the next Atmos setup video I create!
When I listen to music I go in and turn everything off except my towers and run them full range. Trying to make sure I get all he juice of the my Denon that I can!
Hi TechnoDad. Where is the best place to buy some Atmos speakers to get the best bang for the buck? Your video is very informative.
Hi John, Amazon I suppose. I like the SVS Prime Elevation Speakers.
I have ATMOS track enabled mkv video file in my hard drive. Will this/any AVR play from HDD? Or a separate ATMOS enabled 3D/4K player is needed? Please clarify
+Senthil Kumar Natarajan That's a good question. Not sure if an AVR can playback MKV files. I know that my Oppo 203 will play Atmos files in MOV format and bitstream Atmos to my AVR.
Hi, i have a denon x4400h, however i cant get the receiver to display dolby atmos as the sound source. i tried playing the movie through plex media server, and also through xbox one x, still no luck.
I wasn't aware that you can get Atmos via Plex. Very cool! Did you setup the XB1X to output bitstream? Watch this if you haven't: czcams.com/video/Aj6a3JE9DPA/video.html
very good demo Techno Dad....loved the speaker wire lay out doesn't look like spaghetti back there. so if I'm not mistaken you have a 7.2.2 atmos set up?
+Andre Blackwell Hi, thanks! I have a 5.1.2 setup. 7 speakers are being powered by the amp, and only 1 subwoofer.