Bios Settings 7950x3D 7800x3D [Asus Rog Strix B650E-F]
Vložit
- čas přidán 1. 07. 2024
- Click on Settings in Video - Quality - Advanced - 720p60 or higher!! ENJOY!!!!!! :)
(Main Pc)
Radeon xfx merc 310 7900 xtx
Ryzen 7950x3D (7800x3d)
M.B Aorus Elite Ax x670
EVGA CLCx 360mm
DDR5 6000 ram
1440p 360hz 27"monitor
azeron game pad (Mix of controller and keyboard)
razer viper 8khz mouse (the lowest Latency and smoothest)
Soundcore VR P10 wireless gaming earbuds (best for position and foot steps direction!)
* No Sound EQ needed*
00:00 intro
00:15 Bios Settings
09:53 Process Lasso 7950x3D - Hry
![ASUS B650E-F Strix Gaming Wifi [ Unboxing, specification, overview & additional Info ]](http://i.ytimg.com/vi/h2nNwGG0cpk/mqdefault.jpg)
![Bios Settings 7950x3D and 7800x3D [Asus Rog Crosshair x670e hero]](/img/n.gif)
READ BEFORE DOING
If the pc doesn't boot up after applying settings, RESET BIOS BY REMOVING CMOS BATTERY OR PRESSING THE BUTTON THAT RESETS BIOS, Re apply settings but this time ...
Leave sata controller to enable
make sure you are only running 2 ddr5 ram sticks and not 4 to achieve high speeds
If you have any questions, feel free to ask and I'll help the best I can
Hi, can i use this setting for the x670e-e gaming wifi ? I have it with the 7950x3d. Thanks for the help
@s4fety545 yes!
I did all changes, my pc crashes, so i undo the the undervolting still crash if i start a game. Can u pls help me out ?
@@s4fety545 pc specs?
X670e-e, 7950x3d, 4090, 32Gb 6000mhz RAM (2 sticks), my PC crash now without doing anything. Loaded default bios setting- still Crashes now. Did i damage some Thing?
Can't wait to see a video just on Asus motherboard and only for the 7950X3D full stable settings great videos man keep up the good content 👍👍👍👍
This setting work great👍 Previously i have failed at negative 30, now it passes prime for hours. Thank you.
Fixed my FPS Micro Stuttering Issue. Thank you so much 🎉❤
If you applyed all the settings and for some reason you keep goin straight to the bios repeatedly just go to the option where you dissable SATA CONTROLLERS ( advance/SATA CONFIGURATION ) . and set it back to Enable and try it , thats what help me in other to go into windows and not to bios.
Even though my pc lost around -1.7% cinebench r23 score, but the cpu temp went down by 10c on full load! 7800x3d, disabling power down and memory context restor did not work well, it took a minute to boot so i re-enabled them which fixed the booting issue, thank you
Bro it's an option for training the ram before booting.. so it will add some seconds for booting..
Picked up some gains ,4-6% improvements in the mid range cores of the cpu following your tips. Thanks!
How I got lower scores in 3d mark and cinebench
Thanks for the vid man, these settings work very well for me. One thing that I found that can make it better is instead of selecting the processes in process lasso, you can go to cpu affinity and add a wildcard for * and set it to the other ccd. That way it’s gonna apply to all the new processes that may get started while you play
I'll look into it, I appreciate the suggestion I'm always looking to improve and sharing it
How do you add a wildcard? I usually just manually lock the games once I launch them (after clients locked to cache ccd). Would that do the same thing?
No drop fps thank you bro you are Legend ❤
I have no idea what I just modified in each option in the video, but I have more fps and less consumption, please make an undervolt one for the 7900XTX. thanks and regards.
If you put the memory context restore to enable, you boot time into windows is much faster.
does disabling sata if you dont use them have any actual performance effect ? also on the settings why did you not increase the boost clock +200mhz , scalar option has effect to keeps the clocks higher
It won't effect performance in terms on fps but it should slightly reduce overall system Latency, the more things you turn off the better, I saw no difference in gaming when boosting the clock and changing the scalar from the auto option
For the CPU SOC and MC voltage, I’ve heard this should be manually set but I noticed you have yours set to auto. Is auto safe, and would a manual setting of say 1.25v have a negative impact on both?
I have had no issues with auto, you can tweak any of these settings as well, try it out
Did you set in Bios to prefer cache, frequency or auto? I haven't found this in your walkthrough.
Thank you!
good question im asuming cache is the best for x3D's
Frequency for both 7800x3d and 7950x3d, it's mostly usefull for the 7950x3d on the 7800x3d it does nothing if you select either
For 7900x3d and 7950x3d you should select “driver”
@@ramzeslo2 ok, will try this as well
Each reply saying something different.
Cache: It will set everything that runs to prefer the first 8 cores. (The X3d Cores)
Frequency: It will use the cores with the highest clocks. This normally being the last 8 non x3d cores. Unless are limited.
Driver: This will use the x3d driver in windows that gets installed with your Chipset and I think requires Game bar to decide what cores to use (IE Gamebar will detect a game and set its cores to be the x3d cores)
Something missing is also that Asus released a separate BIOS option, that uses an equation to work out if a game is running. called Core Flex. Found under Ai Tweeker. While leaving the Settings above set to Auto.
This work 10000000% thank you my friend
Can't thank you enough ! I was wondering why I was getting insane gpu core load dips and its all because the cpu wasn't keeping up. 7800x3d + 4080 playing bdo. Gpu usage finally stable !
Hi bdo cool
This has helped me a lot thank you! My 7950X3D with 2x32gb sticks of DDR6000 ram, proart x670e benefited from the curve settings by putting the CCD0 to -20 but left the 8-15 cores at P0 since putting them at neg10 started to cause memory crashes in windows.. but it works amazing now.
Quick questions:
1- In the vid at 0:56 you select asynchronous mode ...is that needed if im not changing the dimm timings (sticking with expo2 default).
2- In the Core Flex at 5:25 : Can I use those settings if I only did the CPU core curve and the blck @2000 (I didnt overclock cpu nor touched dimm timings)? The way the vid is set up seems to be that it all works together.
Thanks again!
You can leave it to default, no need to use asynchronous theirs not much benefit from using it
I stopped using core flex and I use process lasso instead on my 7950x3d
Is it worth applying a core voltage offset with pbo combined together or is it unpredictable instability for no performance/Temperature reduction, im currently using a -0.0500 on voltage offset
I wouldn't do any offset, I would leave it to whatever you expo/docp profile sets it at, and if you are worried about Temps, under the pbo setting, thermal throttle limit I put it at 89 which is the max(safe) but you can reduce to whatever you like , but do keep in mind limiting the voltage and thermal capacity you will lose performance
@@Mateo_FPS thanks for the advice mate, I’ll turn it off now and I’ll experiment with the pbo limits, currently on 150ppt 100 edc and 140 tdc
Hey again should i change my DRAM Timing Control or should i just leave it as it is (default)
Theirs 3 settings you should change, but not the timings of your xmp profile
Hey man thanks for the video - I have the 7800x3d + RX7900XT + Asus Rog strix B650-A
Q: Isnt this abit on the upper end of pushing the CPU?
Thanks
This is pushing your cpu but in a good way within the safe zone
Hi. Appreciate your video. I got a WHEA error on OCCT at -30. What are your suggestion? Should I try -28 or -25 or something else? (7800X3D Water Cooled + Asus TUF B650)
Are you in per core or all core? If you go to event viewer in windows and see the whea error, if it says cpu or processor you will need to reduce the undervolt, I believe the apid Id/cpu core
Is 1/2=0, 3/4=1, 5/6=2...etc
Example.. if it says something about processor/ cpu it will also say something about apic id and their will be a number next to it so if it says apic id 8, that means you need to reduce the undervolt in core 3 by 2, I would repeat this until all whea errors are gone, I'm not in front of the computer right now but I'll update me reply with the actual whea error message when I get on my pc
@@Mateo_FPS I reduced the undervolt to 28 and so far no WHEA error on OCCT. Tested some light gaming and seems good so far. By the way, if I disable the Security options from BIOS, I can't login to Windows 11.
I tried optimizing and did COD mw3 benchmarks and i seen a good improvement
If you do per core stress test on occt you can get another boost in performance but it is time consuming and I'm talking hrs like 8hrs min of stress testing
@@Mateo_FPSsome guy in one of my benchmark videos said to adjust the “cache frequency” idk what tat he means by that.
I think he meant to change your cores from cache to frequency, somewhere in the common options in the bios, it says something like *cppc preffered cores*
7950X3D curved optimizer per core 0-7 and 8-15 stable negative numbers to use
Hey any idea after adjusting PBO w curve to -15 all cores , I dont get a BSOD or crash but the cpu cores downclock to 545mhz randomly and system becomes slideshow? after a few minutes the cores boost back up and system runs fine. Did CB R23 benches and no issues there.... weird
I would reset the bios and see what it does , if the cpu is still acting up it might be windows or cooling problem
what should the primary memory timings be for ryzen 7 7700X, it defaults at 36-44-44-96, just wondering what will be best
Just use the profile that your ram sticks came with and see if it's stable, the profiles are good already, even if you tweaked them manually you won't see much performance gains but if your interested in ram Timmings I recommend you watch buildzoid channel , he has a lot of content about rams sticks and timmings
How to understand which core is the best? Which should be done -20 and the rest -30?
Download ryzen master and it will show you your 2 best cores with a star and dot , those you set to -25 the rest -30
after running this i tried to format my pc but my usb flash drive wasnt appearing in bios, when i restored to default it worked, what setting fix it? also, great video, keep your good content :)
If you never touched the bios before and it wasn't working, it could be anything,sometimes the pc just needs to reset everything to fix a problem
I want to do smth similar but with my 5600x should I go and follow the Visio or it will be a big difference?
Everything should be similar, the main difference is how much undervolt it can do
What are your thoughts on using Armoury Crate? Going to try your BIOS setting soon.
I don't use armoury crate I Uninstalled it,I never found a use for it, it was a program running in the background, this will hurt your 1% lows , what do you use armoury crate for?
@@Mateo_FPS I thought as much, I don’t use it for anything, will uninstall, thanks.
@@Mateo_FPS what is the best way to uninstall AC, I have read people have problems getting rid of it.
@@bens5791 uninstall from bios, watch video from 8:35, if it's still their after you do this, download revo Uninstaller and use that to Uninstall
@@Mateo_FPS Neg 30 on all cores, haven’t tried to go any further yet, all stable at this stage. My only concern is my idle temp is now 50-52C, should I be worried about this?
Currently i uv Ryzen 7 5800x3d with co -30 all cores and i just wonder will it safe or stable for longevity if i touch LLC and put all extreme like ur setting, btw i have mb rogstrix b550-xe gaming
Just try it out, if it doesn't work all you have to do is reset the bios, this is not going to destroy your comp, just don't mess with the voltage
Nice video, thanks! (subbed)
I'm on b650e-f gaming wi-fi, 7800x3d, rx6950xt... I find that these settings don't really do anything performance wise (for me - maybe because this cpu can max my graphics w/o xtra boost needed?)... my cpu freq + temps are the same as before. The only thing that changes this for me is the CORE PERFORMANCE BOOST (I will call this CPB form now on) setting: Auto/Enabled will always push the CPU to 5050Mhz max freq, regardless of PBO settings (both in the asus and amd menus for it), and nothing will effect how it performs. If I turn off CPB, the CPU will default to its 4200MHz max freq, and never go past it. Am I missing something here? Should I not be able to run PBO w/o CPB enabled (keep in mind, this is a setting for AUTOMATIC overclocking), which seems to me to overrun any other settings I make? P.S. I use HWinfo for CPU readouts (HWmonitor clearly does not report correct info when it comes to freq on my CPU).
If you game at 240hz or less their is no need for this, this is for people who game at 360hz and up, I should have probably mentioned this at the beginning of the video, you will see a performance gain if the game is more cpu bound, even the 4090 is not good enough for the 7800x3d/7950x3d
Something odd is probably happening with your boost, it will be hard for me to tell from my end, but one thing you can do is, have a power plan for gaming only and a power plan for everything else, meaning your non gaming profile make sure the power limit is not 100% this should turn off the boost
@@Mateo_FPS @Mateo_FPS Ok! Gtk! I game at ultrawide 165hz, so I guess I'm good then 😎. But I do notice a slight difference when multitasking, programming and doing graphic design if I don't have boost enabled. So I just was wanted to max the cpu as much as possible w/o it getting so hot (which it does when CPB is enabled). Anyway, big thanks for your reply! I will look into having different power plans.
I honestly didn't notice a noticeable change, I feel the same.
If your not gaming at 360hz with a 4090 or 7900xtx this is pointless to do
if I have a fps rate above 700hrz, as soon as I perform a bechmark and a stress test and if the numbers went up, I already saw that 8 processors run above 5,200 mhz and the rest at 4,500 mhz almost fixed, I have Ryzen 9 7900x3d and rx 7900 xtx, I think if I improve, R6S gives 2739 fps in main and in game 400fps, more games need to be tested.
@@Mateo_FPS
Hi! I'm still studying your build on 7800x3d, gskill 6400 cl32 xpm. I liked the results of OCCT SSE. But I still have the only question, how did you come to LLC 3lvl? LLC has the property of dangerous processor surges, it's very important... It's important to know that it's safe
LLC is more of a trial and error because it doesn't really show what values it has, but if you were to leave it on auto you will probably see no performance loss, it's more for stability of you oc/uv
If you did your uv per core on occt then this setting you should leave to auto, this is more for people who do all core
@@Mateo_FPS LLC lvl 3 will Vdrop the use of voltage when the CPU is on high usage.. so more lvl like lvl 4 will undervolt more but will be more unstable.. LVL1 will be almost between the positive and negative line from 0 to -1 for example so u will go more safe not undervolting.. so ur negative 30 all core will be more stable.... or maybe u can increase to negative 40 o 45 all core.. (golden CPU)
Hi bro, just want to make u know that you make my PC a complete monster, now games feel completily responsvive. Im running 4070 ti and ryzen 7 7800x3d. Thanks❤
I appreciate the comment, I just made my channel to help others, I know it's frustrating that utubers are just making videos for click bait without actually giving you the right info
@@Mateo_FPSdo u do anything else to decrease input latency?
Apart from overclocking controller and nvidia settings
@N-ro8wv the only other part to check is turning off background services that you aren't using or bringing down the processes running
is there a reason you did 1/3 times to flck? ive never heard of that and was wondering if it was a new thing for 6000mz ddr5 sticks?
Maybe I shouldn't have word it 1/3, but most people/"experts" say for ddr5 the flck should be speed/2 and then divide 1.5,....6000/2, 3000/1.5, so It would be a 1:3 ratio, this should be a typical stable oc that would work for everyone but it can still be fine tuned to a specific computer, it can be lower or higher depending on what the computer allows you to do
@@Mateo_FPS ahh i see ill definitely do more research on that for my next build!
Hey why is there a difference betwen this video and the crossair one the undervolting on the 7950x3d and on this video u disable intergrated graphics but not on the crossair video?😊 im just trying to figoure out whic to fallowe since this video is newer
That video was the first one I made, so I might have missed a couple of things as far as undervolt their is different ways to do it, this is a simplified version and more recent, so follow this one instead, I'm still looking more into the bios to see what else I can modify
I am running a PC with the exact same CPU and Motherboard as you, but for some reason anytime I enable PBO it will no longer POST (even without any of the other changes you recommend). Since it looks like it that’s not a problem for most others, any ideas what the issue could be?
What's your pc specs?
@@Mateo_FPS Motherboard:
ASUS B650E-F ROG STRIX GAMING WIFI AMD AM5 ATX
CPU:
AMD Ryzen 9 7950X3D Raphael AM5 4.2GHz 16-Core
GPU:
Radeon RX 6600 MECH 2X
Memory:
TeamGroup T-Create Expert 32GB Kit (2 x 16GB) DDR5-6000 PC5-48000 CL30 Dual Channel Desktop Memory Kit CTCED532G6000HC30DC01
Cooler:
ARCTIC Freezer 34 Esports Duo - Tower CPU Fan with BioniX P-Series case Fan in Push-Pull, 120 mm PWM CPU Air Cooler, for Intel and AMD Socket, LGA1700 Compatible
Power Supply:
be quiet! BN513 Pure Performance Power 12 M 1200W Modular Quiet Performance Power Supply | 80 Plus Gold | ATX 3.0 | for PCIe 5.0 GPUs and GPUs with 6+2 pin connectors | Silent 120mm Fan | BN513i
SSD:
Crucial T700 2TB Gen5 NVMe M.2 SSD
@@Mateo_FPS Motherboard:
ASUS B650E-F ROG STRIX GAMING WIFI AMD AM5 ATX
CPU:
AMD Ryzen 9 7950X3D Raphael AM5 4.2GHz 16-Core
GPU:
Radeon RX 6600 MECH 2X
Memory:
TeamGroup T-Create Expert 32GB Kit (2 x 16GB) DDR5-6000 PC5-48000 CL30 Dual Channel Desktop Memory Kit CTCED532G6000HC30DC01
Cooler:
ARCTIC Freezer 34 Esports Duo - Tower CPU Fan with BioniX P-Series case Fan in Push-Pull, 120 mm PWM CPU Air Cooler, for Intel and AMD Socket, LGA1700 Compatible
Power Supply:
be quiet! BN513 Pure Performance Power 12 M 1200W Modular Quiet Performance Power Supply | 80 Plus Gold | ATX 3.0 | for PCIe 5.0 GPUs and GPUs with 6+2 pin connectors | Silent 120mm Fan | BN513i
SSD:
Crucial T700 2TB Gen5 NVMe M.2 SSD
hey my 7950x3d is now hitting max boost finally lol, i dont know what i did but it was never boosting higher than 5350 before with a - 27 offset
Glad to hear it!
Hi, can i use this setting for the asus 650e-f gaming wifi ? I have it with the 7800 3xd and ram Corsair VENGEANCE RGB DDR5 32GB (4x16GB) 6000MHz C30 since my system is a bit unstable. Thank you very much for your availability.
Yes, and read my pinned comment before you start
@@Mateo_FPS ok tks
Hey, I am noticing my boot always goes through the mem training... Yours on the end doesn't, any tips for disabling it?
Mine did I just clipped it, but if you want to boot up faster, make sure fast boot is on and memory context restore is enabled
@@Mateo_FPS thank you!
Any advantage on letting it do the full process?
@RodrigoBraga some people notice issues with stability with memory oc and disabling memory context restore will solve it , but if you have no issues then leave it enabled
i did read in some places that c states should be enabled on the 7800x3d
Try it enabled and disable, whatever works best for you and your system, these settings are a good point to start and tweak to your liking, I personally do things for performance
I've tried everything and I can't get windows to auto park cores when running a game thru Gamebar. Any idea what could be the issue? I've followed all of the instructions online and all of my drivers, etc are updated.
I have a Asus B650, 7950X3D and a Asus RTX4090
Did you use process lasso?
@@Mateo_FPS I just figured out what was wrong and I feel stupid as hell 😂
I did have the the windows power plan on Balanced. I switched it and now it's parking like it should
I have the exact same processor and mainboard and applied these settings. Every now and then while streaming inside my browser my PC crashes and restarts immediately. Should I increase the undervolting to something higher than-30?
Are you familiar with occt? You can lower the undervolt for now to -28 if it crashes again lower to -25, if it crashes again you have to undervolt per core and see which core is the problem
@@Mateo_FPS thanks, will try that 👍🏽
Hello i have on 7800x3d, asus strix b650 and 6000mhz cl36 corsair rgb but it’s impossible to start at 6000mhz (black screen and back in the bios with a safe mode), at 5200mhz it’s OK
You don't have to do safe mode, just reset bios by removing cmos battery or click on the button that resets bios settings, you should be able to run 6000mhz
Disabling the c-state iommu and df-state doesn't heat up the processor more?
If you have a good aio or a good fan this should not effect you at all, but if you cheaped out on a cpu cooler it will get warmer, nothing that will damage the cpu. Since the cpu will just throttle down if it gets too hot
@@Mateo_FPS i have an kraken elite 240mm
is good?
@Friarello_ yeah you should be fine
Friend, help... 7800x3d, gskill 6400 cl 32, xpm. ASUS b650e-e... I can safely apply your settings for x3d, but ddr5 set the DOCP profile 1...?
Yes
You most likely need to drop your xmp to the 6000 setting. I have almost same setup as you and I needed to do this. Assuming you have 32gb of ram on 2 carts. So 6400 cl32 32gb. I'm on the gigabyte b650 auroros elite, 7800x3d
thanks for the vid and effort brotha , so i set everythin like you have it but evertime i turn on the pc , It goes straight to bios, dosent give me an error or anything n i already lower the curve to -2 already and it just does the same thing over and over, any idea? 🤔
Default the bios and try it again, wait a couple of mins to see if it loads into windows
@@Mateo_FPS oh ok how do i default the bios ? ma bad for my noobieness , i was trying to go to the boot option on the bios to set it to prioritize to start with windows but i cant even find that option
@@Mateo_FPS but dosent all the settings reset to default if i reset the bios ? 🤔 .. i really want to try your settings
@@Mateo_FPS im trying to find out wats not letting it boot up into the windows since its not giving me no errors at all
once i did all your settings , all the boot ssd options are gone, im trying to see if i can bring it back
Hey there, everything is working great except that i can't open faceitac saying that i have to enable tpm2.0 even though it is enabbled in bios, any help here?
Reset bios, and see if it fixes it, if it does re do everything and leave tpm enabled
@@Mateo_FPS Found the fix, apparently security device support needs to enabled for some reason, thank you very much for the guide!
Hey!
Asus strix x670e-e
7800x3d
Corsair dominator titanium 6000mhz cl 30 2x32
Cant setup ram freq CPUZ showing 4800 cl32 when I able expo motherbord showing 6000 but when I check by cmd and cpuz still locked 4800 cl32 any thoughts?
Go to task manager
Performance
Memory
Speed :
Check what your speed is here
Cpu z only shows you half the speed on memory tab I'm running 6000 but on cpu z it's showing 3000, on SPD tab does your max bandwidth show ddr5 6000 (3000mhz)
If you did change it in the bios and it doesn't show in cpuz you can try uninstall cpuz using revo Uninstaller and re install cpu z
CMD with command: wmic memorychip get speed still showing 4800mhz @@Mateo_FPS
Damn i only have done the curve optimizer negative offset 35 and it gets better then i did C state off and it gained like 10fps average
My 7800x3d crashes -32
@@Mateo_FPS really ? So did you drop it to 30?
@@Luckytmj97 yeah
What does is most optimal for the curve optimizer and what does it do.. ive done it, and i put it on -35 negative on all cores.
Is it better at lower set point ? Lile 30 or 25? Or is higher better ?
Correction i used OCCT and i dropped it 20 and it was stable
Is 120% safe for VDDSOC Current Capability? What does it change? Soc voltage not to lead 1.3? Thank you, friend, for the answers!!!!
If it's not in red its safe
@@Mateo_FPS Do 120% increase the voltage? Or do they optimize the voltage? I have 1.3 in my normal settings bios
@@Mateo_FPS Friend, I don't understand what 120% and 100% mean, what's the difference between them? What's safer? I'm afraid if there's more tension, because I don't understand it
@@xxktulxa7182 100% means normal 120% is allowing more, if the letters are white it should be safe, if you don't feel comfortable then leave it at 100% just not less
Is there any way to customise the r9 7900x ? ASUS Tuf gaming x670e plus 😢😢😢
Same thing,just copy the settings that are applicable to your mobo,
@@Mateo_FPS What I don't understand is, will they increase the frequency?
@byDo4a if you undervolt you have the potential to increase frequency, the higher the more fps you can achieve, probably up to 10fps or more in gains, which might not seem like a lot but companies try to sell new cpu that are barely 10% increase performance
can you remake your guide with new 2214 bios options pls?
I will look into it, but it shouldn't be different from these settings
this work with a Asus ROG Strix X670e-E gaming WiFi ? using a 7800x3D and Corsair6000mhz ddr5
Yes
If you have any issues let me know, these settings are super basic it should work
disabling memory context restore makes my bios boot time go from 9 seconds to 40 seconds. Why would I disable this?
Some people have issues when they oc their memory, so disabling memory context restore will help with stability, but if you care about boot times then leave it enabled but if you have issues with memory, disabling this will help out as the pc makes sure it's all good before it boots up
Would this apply for a b650e-e with a 7800x3d
Yeah
Can I use your settings on B650e-f 7800x3d rx7900xtx oc ?
Yes, this is to maximize your cpu so that you can get the most out of your gpu, plz read pinned comment before you start, and I would recommend you try resize bar on and off to see which one gives you the better performance in the game you play
Do you not enable pbo in amd settings?
You can put it on either one, it's the same thing
Ive just done this mate can you tell me what cinebench 2024 scores you got on 7800x3d please buddy
I don't do cinebench, I do only gaming benchmarks
Oh okay 👍 was just playing cs and it crashed so I've lowered by -2 like you recommended
@richardelliot4372 what kind of fps are you getting on cs? I haven't played it in a while or checked my fps I've been busy with mw3 material
@mateoDaK1LL3R I've gone from an 8700k to 7800x3d and the difference feels like night and day on tarkov and cs at the moment my fps in cs is 300/400 but smooth as butter at 1440p
I have x670e-f and 6400Mhz memory kit when aet the voltagea on auto it set the SOC VOLTAGE to 1.341v but my Soc LOCAL voltage reading is 1.285 v and the VDDIO to 1.431v is safe ? Ive already updated the bios to 1904
If it automatically did it, it should be safe ,you can also set them to what you want manually if you are worried about it
@@Mateo_FPS well when I manually set the SOC VOLTAGE to 1.25 and the memory frequency on 6400 my games keep crashing and ran to system instability
@RainOnWarpaint it probably needs more voltage, have you tried running your expo profile settings? And does that work?
@@Mateo_FPS My kit is XMP BY THE WAY, I've tried to use DOCP 1 with 6400MHz frequency
@RainOnWarpaint without any modifications does your xmp profile work?
Nice Vid. Can u pls tell me what yous scores on CPU BENCHMARK on warzone 3 ? AVG, 5% e 1% Low. Thanks in advance.
594 avg 432 5% 372 1% that's what I get on my mw3 benchmark
@@Mateo_FPS Can u pls tell me what is your config ? I have the 7950x3d with CL 28 6000 Mhz and tunned sub timings. PBO 020 Curve Optmizer and i only got 550 380 340. Can u pass your bios config ? and windows ? Thanks in advance.
Any other TIPS ?@@Mateo_FPS
@@murilocantharino2034 czcams.com/video/zXgKsW3kC5E/video.htmlsi=CMrG2th-A2DDLD97
@murilocantharino2034 that video is most of what I did, the only difference is my cpu is undervolt better , cuz I spent hrs figuring it out, I didn't make a video cuz I don't think people will waste that much time doing it, one other thing you can do is download ryzen master and see your 2 best cores, and undervolt them -20 and the rest -30
Do you know if asus has fixed all the problems with expo and burning the cpu? I have the same board and cpu as you. Should i use expo I or expo II?
That was fixed a while back, just make sure your bios is up to date, try expo 2 if you have issues then try expo 1 or vise versa, I didn't see any performance difference but for me expo 2 just felt better imo
@@Mateo_FPS also gets false readings in hwinfo64(hopefully) die average temp spikes at 130c while core temps maxes around 67 while gaming. Uninstalled armory crate and will try again.
@@jakobandersson6679i get the same problem on cpu temp. Did u get it fixed?
@@Toffetoffe85 it has slowes down and only appears now and then. But i monitor temps and are 100% its double readings so no worries
So this only works for the Asus Rog Strix B650E-F? Or can I apply these settings aswell on my "ASUS Prime B650M-A II"? (i have 7800x3d)
Should work the same, all you have to do is look for the same names
alright@@Mateo_FPS TY. I only play CS2 and Rust, do you think I should apply these bios settings, for more fps and 1%lows? And what do you think about "System tuning"? - should i leave it normal or PBO enchancement?
@augustgrnkjr7697 these settings will improve cpu performance by how much may vary, but It will be better than stock, I don't mess with any special features they tend not to work well, I tried them and I lose performance
@@Mateo_FPS im quite a boomer. So when i apply theses settings my base speed Ghz will improve right? right now i will get 4.2 GHz (which is the base speed) on 100% utilisation. Isn't that kinda bad?
@augustgrnkjr7697 it's a problem if you have a game open and it stays at 4.2, when you are gaming it should boost up to 4.7-5.1 , if you look at my other videos about full optimization for mw3 those apply to any game
Thanks, my 78003xd CPU is finally running quietly and not overheating, but sometimes the system freezes or there's a Windows crash. Do you have any suggestions on what could be changed to make it more stable?
Stress test it on occt, if you get an error than reduce the undervolt by 2 test again and repeat until you can stress test 1 hr without errors, if you want to know how to do per core later on, just hit me back up
Thanks for quick response! Do you use discord? I will try on 28 now.@@Mateo_FPS
Thanks for quick response, I will try on 28, Do you have dc?. yh on occt i did get bs after 10 sec lol@@Mateo_FPS
Try this instead
Set -30 curve per core on cores 0-7
Go to occt
Cpu option
Data set- large, mode-extreme, load type-variable
Thread settings- core cycling
Type-custom
Physical core configuration
P0 make sure it has a check mark and cores p1-p7 make sure it has an arrow
Cycle internal -45 seconds
Threads per core -32
Then click start
This should tell you what core needs less undervolt
@@Mateo_FPSI will do ! thank you very much
I have EXOS running but I get instability in games so I have to set it back to auto, I heard its a voltage issue how do I increase the stability so I can have my ram at 6000mhz?
Is your pbo at -30?
And are you familiar with occt?
@@Mateo_FPS I used it some.
@@Mateo_FPS -24 on first 8
Set -30 curve per core on cores 0-7
Open task manager
Go side bar Details
Under occt.exe right click
Set affinity you are going to select cores
0-15
Go back to occt
Cpu option
Data set- large, mode-extreme, load type-variable
Thread settings- core cycling
Type-custom
Physical core configuration
P0 make sure it has a check mark and cores p1-p7 make sure it has an arrow, cores p8-p15 make sure it has the red circle with the diagnol line across
Cycle internal -45 seconds
Threads per core -32
Then click start
This should tell you what core needs less undervolt
Hey, someone can confirm that on the B650E-E (not the F one) that we can disable the sata controller like on the F please ?
Are you using Sata?
@@Mateo_FPS no, I would actually like to be able to deactivate this controller. that's why I'm asking the question if it's possible to deactivate it on the B650E-E.
@ColonelStrike yeah you should be able to, I have it off in my asus mobo and aorus mobo
Yo I need help, so I set everything up as in the vid (I have 7800x3d and rtx4070ti super) besides curve optimization, I put it on -20. My pc wont boot, or better said it says its unstable and gives me an error, what should I do?
Reset bios and redo only the first part of video
If you still have issues let me know I'll be on my comp
Alright thanks, up to where tho? Idk what part u mean..(sry) also I tried -10 curve optimization aswell but didnt work either
I set bios back to optimized defaults now its completely frozen
@@Moonplayaa from 0:00 to 3:30
HELP ! I follow the steps in the video. And now my motherboard keep the DRAM on when starting, doesn't let me go to BIOS or anything. Just a black screen and a Orange Light (dram) on the motherboard !!!
Did you read my pinned comment?
@@Mateo_FPS yes. Everything is set like the comments. But still won't boot. Always get the orange light on DRAM... It used to work before with the same settings, I followed your video like 5 months ago. I just updated the bios to the lastest 1623, don't know if that's the problem....
@@Mateo_FPS Ok so what makes my computer work again was to put FLKR back to auto instead of 1/3 of my RAM and power down enable&memory context restore back to auto.
(RAM is T-Force Delta 32Gb kit 6800)
@QuentinMatthysBoeckmansYJ just curious what kind of motherboard are you pairing your ram with? Most mobo support up to 6400mhz speed so 6800mhz should be unstable
@@Mateo_FPS Asus Prime X670E Pro WiFi.
Everything was perfect after setting curve optimizer -30 .. then i want to start CoD Warzone and it dosen't start (dll problem) .. other games start.. reinstall CoD wasn't helpful.. i went back to "auto" and CoD start.. win11 7800x3d asus b650e-f ?! Maybe test -28 -26...?
Are you familiar with occt?
No .. what do you think is the problem?
@SK87bln one of your cores probably has to much undervolt, occt will stress test your cpu and tell you which one is the problem
For some reason doing these settings gives me BSODs even at - 0. Not sure g I'm doing something wrong, but I followed the video exactly.
Just reset bios and try again, if not just do your expo and see what happens
hello dude , this board can handle a 7900x? and , i can overclock like you on video?
Yeah same thing, this works for the 7000 series cpus, just keep in mind that how much UV you can do is going to vary on cpu
@@Mateo_FPS thanks man, help me a lot . thinking about intel or amd plataform...
i have in mind a Kit z On 14 i7 intel or Amd B_E Kit with 7900 or 7900x...
On same price, what you choose?
@Renansilva-tu2fp you can't go wrong with either amd or intel, if money ain't an issue you can do all intel to get the best but if you are on a budget, get the most out of your money and find deals, I'm all amd and my cpu performs just as good as 10000$ intel pcs, I would go with 7900x, the x versions are always better,
Intel - tunning level moderate/hard
Amd - tunning level easy/moderate
@@Mateo_FPS in my case in brazil the plataform Z+ i7 14 gen is same for AMD 7900 + B650E. Imm afraid about intel because the overheat... i will buy a 360 liquid cooler but im afraid of high temps, and i see the 7900 and 7900x have tdp of 170w so this is less then any i7 modern breaking 250w easy
@Renansilva-tu2fp just make sure to buy a cpu frame (thermal grizzly) and be generous with the thermal paste, and a good 360mm aio pump and you will be good
I lose warranty if i play with this? And for the armoury crate. I love and use the app since it controls all my devices. Can it work with this settings?
You will if you tell them lol but these settings don't break your system, only when you start messing with the voltage, and you could use these settings with armoury crate, but keep in mind you will lose performance in the 1% lows on your cpu because of armoury crate
I got you, its just that I'm a bit scared cause it was a lot of money for me getting this build after a year of saving. Anyway my biggest issue is buzz sound when visually demanding games are played and I'm trying to figure how to fix it and what causes it. I suspect AIO pump. I will try your settings to see if it will fix it. That is how i end up here anyway..trying to fix
@francisunderwood707 what's your pc specs?
@@francisunderwood707 it's either the pump or gpu (coil whine)
@francisunderwood707 these settings are to increase your cpu performance
After doing exactly like you it is impossible to launch valorant because of the tmp 2.0....
Reset bios, and just follow the video up to 3:30
Hi, could you do a video for best settings for Ryzen 7 7700X , or can i use these settings? thanks.
These settings should work, the only thing that is going to vary is the undervolt
ty vm
190 avg fps cs2 -> 380 avg fps cs2
7800x3d + 2070s
Very well ❤
Nice!!
i don't recomment copy pasting these settings because of silicon lottery.
If your BIOS AI Tweaker (RAM overclock) shows DOCP rather than EXPO, then you probably have RAM that is Intel XMP optimized, rather than the AMD version. Hell knows if this even matters, but that is how it seems to be.
It should be fine, I use both xmp and expo on my rigs
Yo my question i have asus tuf x670e plus on ur video cpu loadline calibration u have only 4 different level but i have 8 different level which level is better for me level 8?
I would leave it somewhere in the middle either lv 4 or lv 5, does your mobo give any details on the LlC? Like a graph or brief description?
@@Mateo_FPS no its only 8 levels i watch ur another video for asus rog strix u setting level 8 im not sure which level better for me best fps n input lag
@sirdawn4325 this setting here its more to stabilize the uv/oc of your ram if you do (all core) if you UV per core theirs no need for this and you can leave at default
U mean pbo per core? im using per core yh
@sirdawn4325 when I say per core I mean , pbo per core but you stress tested each core to know it's max undervolt value
can some of this be copied to asrockx670e steel legend?
Yes, just as long as it's the same name
@@Mateo_FPS do u have a discord? Can we go in a voice call and I can show u my screen?
@@SwerveNation I don't have a discord set up for this account yet, I can try to help you as much as I can through here
@SwerveNation most of these settings are the same across different mobo
@@Mateo_FPS ok I'll test these
My realtek audi has vanished after this, no audio now, it's not appearing in device manager either.
Did you disable the audio?
Figured it out. Had to re-enable usb audio controller.
@@Mateo_FPSyeh I figure it out, thanks.
System won’t boot to windows now and boot priority option is locked
Reset bios and only do the first half of the video, or turn on sata if you disabled it
@@Mateo_FPSit was the sata thanks bro
Sata controller disabled?
Yes unless you are using it
I did everything as shown in the video. It takes too long to restart the cpu. The cpu also takes a long time to turn on. Please answer
Yes, because it's updating the settings, if if doesn't turn back on, it could be that the undervolt might be too much
@@Mateo_FPS It always turns on slowly. It is the third day. what can i do can you help me? But in games it is great
@mishazakaraya3341 go back into bios and Enable _memory context restore_
@@Mateo_FPS I did it, but there is no result
Thats the expo setting at the start of the video(DOCP profile 2 but they all do it once set). It run's the memory at the rated speed and not the default 4200. If you have it on, the system does a memory training at each boot. The Enable memory Context setting is to help reduce this. Also make sure your memory is correctly placed (slot2 and 4 if a four slot board) and you are not trying to run 4 sticks of memory. (2 is the current recommendation for the X3d based systems). But this is normal behavior, so nothing to be concerned about.
Wish me luck, I did that on a 7800x3d
How it went?
all good@@loirow_
I got lower scores in cinebench and 3D Mark Time Spy
@@ThisIsZaphhe disabled Svm lol, I’ve stopped watching at this point. Svm = hyperthreading. Enable it and you should get your performance back
R u alive
7800x3d with 7200mhz 32gb cl34 ram is it possible?
What mobo do you have and how many ram sticks?
@@Mateo_FPS Corsair dominators 2 sticks , what is MOBO ?
@@Mateo_FPS motherboard is Asus x670e - a gaming
@xwiair3426 so I looked up your mobo and it will support up to 6400mhz stable, 7200mhz it's only possible with an intel pc set up not amd, but if your ram sticks have a default profile try it and see if it's stable,but you can use these settings and if your pc doesn't boot up reset bios and try 6400mhz speed
So the limiting factor here is the mobo?
I do not have Advanced/Amd PBS tab
I did complete it I found the setting however mine did not reboot as quickly as yours
@@mateoarteaga5086 I edited the video because it took a while to boot back up
In fact I’m still waiting for reboot after bios changes right now 10 minutes later
It doesnt connect to internet afuera putiing everything here
Are you using wifi or ethernet?
If you are using ethernet you should be fine but if you turned wifi off and you use wifi , go back and enable it
My Ryzen 7 7800x3d can go to -40 Curve optimizer and stable 😊😊
I doubt that, unless you are water cooling, you are probably core stretching, because I know if you stress test per core, anything above -32 it's a crash
@@Mateo_FPS yes im using water cooling
@@Mateo_FPS but when i test on -50 all core, my PC went crash
@@veltgaming9492 nice! I bet those cpu numbers are crazy!
My 7950x3d REALLY didn't like this one bit :D
What did it do?
@Mateo_FPS BSOD after BSOD. In the end i had to reset the bios. Previously, i had it stable at all core -15. There must have been a few settings that it didn't like being changed.
@@lupuslycos88 did you oc per core or all core?
I tried using ryzen master and it keeps saying curve Optimizer mode off 7950X3D b650e-f
Ryzen master sucks! Do these directly in bios
I got blue screen of death stop code memory management
Stop code: system thread exception not handled just giving me back to back blue screen codes should I reset my bios?
@@mateoarteaga5086 just boot back into bios and reduce the undervolt
@mateoarteaga5086 if the pc doesn't boot up then reset bios
@@Mateo_FPSwaiting on screen now after dropping it to 28 days preparing automatic repair
Says*
curve -30 all cores CCDs..facepalm...
I'm using a negative 30 also, why are you against that? Just curious, I set it up when it first came out and at that time couldn't even get the ram to post stock. Lol with all the bios updates I can enable expo1 , and I just tried a negative 30 offset and it worked , I never even tried to keep going lol do you have any other suggestions?
I'm using a gigabyte Aorus X670E Master motherboard though.
Nice video. I applied most of the changes for my 7950x3d (minus some of the optional changes) I was gaming for about an hour and then I got a total power off mid game and reset. Do I need to change the curve on cores 0-7?
@DryLipJohn , I'm just throwing this out there but if you saw me and the OP talked for awhile trying different settings.
I'm using the ryzen 9 7950x3D obviously, with a gigabyte Aorus X670E Master motherboard,
And all I changed was I set ALL cores to negative 25.
I disabled the onboard graphics (I can explain why if you want to know more)
Set the pbo limit to my motherboard just like this video, set the max temp to 90 (it was 89 in this motherboard)
That was it with the cpu I'm pretty sure
The memory I set the same as his
Expo profile 1 which made it run at 6000mhz
I did change the mcclock (or whatever its called in this video ) to 2000mhz just Like the video shows
And set the baseclock to memclock (I think it could be called something differently) but again it's all in this order in the memory dram settings .
So my memory settings were changed all to the same as his,
I didnt disable all the stuff he disables except onboard graphics. And set the pbo to negative 20 offset for all cores.
(If you have my motherboard I also changed the programable button we have on the bottom right hand side of our motherboard if your looking at it mounted in the case. (You can program that button to do several things. I changed mine to boot to bios immediately. Now when I mess around and would normally need to reflash my bios, or reset my cmos which is even worse because to do so I have to remove my gpu, plus my motherboard heatsinks, now I just can push a button. Very handy.
Anyway , my results are when my cpu is running at its slow core setting its 5325mhz, and when it's running at its fastest speed its running at 5725mhz.
Temps are idles around 38°, but never has it even gone over 80° during cinebench or any other benchmark. If I knew more I could def squeeze even more performance out of this chip but 5725mhz is fine for me .
You def can get better performance. By changing it a core by core basis but I don't know how to do that, I know ryzen tells me which 4 cores are My fastest but I don't know what to do with those 4 cores? Set them to negative 20 instead of 25?
Reduce the undervolt to -25 if that doesn't work it's probably the ram
Thanks for the reply guys. I’m going to try -25 on core 0-7 . Any specific test that you guys recommend ? I have Occt just not sure exactly what’s the most optimal test.
Damn my 7950x3d SP 110, cant go more than -16 on core 0-7. Any tips or just the sillicon?
What have you done so far? Just so I can see what's going on? Also what hardware are you running
B650e-e 6200 c30 fckl 2033 + settings from the video, only vddsoc 1.2