SHARP AQUOS TV "LC-60LE650U" flashes 3 slow, 1 fast. No back light or sound. Here's the fix.
Vložit
- čas přidán 10. 03. 2019
- Hi all, I'm sharing my knowledge with you all today.
A customer brought me his SHARP AQUOS TV "LC-60LE650U"
this fix might work for other similar model sets.
It was not turning on at all, just flashing a code of
3 slow and 1 fast flash. After checking and looking on the net, I couldn't find a schematic. But did see quite a few people with the same issue, but no fix. the code seemed to relate to a com error between the TCON board and the CPU. But that wasn't the case here. so I'm sharing my findings with everyone.
Forgive me for flip flopping around trying to explain things on the fly. But i think everyone will still like the info.
Comments welcome. Be safe.
Oh, BTW the regulator is a KIA378R12PI ( 12V Regulator with turn on control ) - Sport
I wish I had seen this about a week ago. I just got tired of messing with my Sharp and it had the same fault and symptoms. I had replaced the backlights because I had the one long one short fault code to begin with and it worked for a bit then went into the fault mode like yours. I also had a quarter of the screen stop displaying right before it happened. I couldn't find no info and got tired of troubleshooting it and ended up just breaking it down and giving up. Thank you for the info though because now i can locate where i put my power supply board and repair it and maybe sell it to recoup some of my loss. I know they want an arm and a leg for the boards in these tv. Good find bro!!
Great Vid Jay. I’ll pass this on to my Sharp tech.
Great job Ray. I would wager that this video has temporarily postponed a few 1000 TVs' trip to the dump
Mr. Ray speaks the truth. Seems to be a common problem on this model power supply board.
Same fix for a a 70" LC-70LE847U Sharp Aquos. In my case, the power LED was 2 slow and 5 fast which indicates display (panel) fault.
Normally fatal but having nothing to lose I checked the regulator anyway. 8.4 volts on pin 2. I want to say I got the replacement KA378R12
off eBay but not sure, anyway they were 2 for around 10 bucks shipped. It's a readily-available part; look it up on Google.
Make sure to remove the old thermal paste on the heat sink and apply new. Don't overdo it, a light even coat on the back of the part is fine.
The TV's been running sweet as a first kiss for a year or so now. (I got it free off off the local Craigslist) 10 bucks well-spent!
I'm Glad you got your TV repaired.. Good Job..
Thanks for the share !
Thank you sir sharing idea 👏👏👏👏
informative video....thanks!
Excellent I have a similar tv with the same symptoms and started to doubt in my theory and internet start to convinced me that was TCon board, but thank your video now I know i'm not crazy
Glad I could help ! Good Luck
Thanks you my TV works again, tkank you very much
Awsome... Was it the part i mentioned ?
nice job. I have a similar problem, hope im as luck as you thanks
Nice fix
Hi very informative great video have the same problem have to source a regulator thank you.
I bought a few off of Ebay.. Easy part to find..
Nice component level troubleshooting. Thanks for sharing.
Tanks for the video. I hace a 60 inch tv with the same problem. I Will chec tath regulator .
Mine is aqous LC-50LE570X it has red standby and blue (switch on) but still no display no backlight no sound I tried to check the output voltage on standby it starts on 9v slowly going zero...do u have some advice for my tv?
Hi Ray, where did you find the a KIA378R12PI ( 12V Regulator with turn on control ) I have ordered two sets of regulators these are not the turn on control regulator? Can you please provide the manufacturer where you purchased your regulators? Thanks a million!
I have the same model... I've been having power freezes (power light on, black screen, no response to remote) for years...backlight has never functioned...but no flashing or error code... I have to unplug it, wait 10-15 minutes, then plug it back in... Assuming that It needs that time to disapate the charge... Do you think it's the same regulator causing it??? Thanks for posting this... :)
Hi I have ah sharp aquos lc-55le620ut model do you have a experience to fix that no power no blink but I try to test the supply have voltage and suggested pla thanks
hi there i have sharp LC 60LE640x
on power supply board the backlight jack have +84 but -84 missing thats y backlights not getting on?
Hi Ray,
thanks for your video. I have the same Sharp model... it's been an excellent TV, until recently. I was wondering if you or your readers have any experience with this model, regarding local digital channel reception (re: antenna)...
We don't have cable (for channels), but currently are using internet sucessfully for internet channels like CZcams.... we cannot any longer receive any local digital channels
My Sharp will no longer receive any local Digital channels (have done several resets, as per set-up, which has always worked in the past. I'm getting an error message "remove scrambled channels", which we never had this message in past years.... is there a digital tuner chip in the TV that might be defective?, or is this scrambling new? Thanks
The antennae, cable & transformer have all been changed,
I will send you one litre of vodka if its Voltage Regulator on my TV mobo, almost same model, exactly same led flashing sequence. Just got a TV for free. Taking in my hand screwdriver to check tommorow. BR from Poland.
Good Luck
PS where can I buy that regulator from do I have to order it or can I go to like Best Buy or any local store to find it thank you
Hi Ray, thanks for the video. I realize you may not know the answer to this, but I appreciate that you are taking the time to respond at least to other questions.. I am wondering where that turn on voltage, pin 4 on that regulator is getting its 3 volts from? That seems to be the problem with mine... I have 12v on pin one, but only millivolts on pins 2 and 4, I changed out the regulator thinking it was at fault, but after researching your video a few times I think I’m understanding that pin 4 needs to be getting 3 volts from somewhere in order to “turn on” and send voltage out of pin 2... is this correct? And do you know where it should be getting that voltage from? Thanks again!
Check your other voltages on that board. You should have 5V standby voltage for one on another white connector and others. You could also trace the circuitry back to see where your missing voltage on that pin comes from. I wish these videos would show the schematic, if possible, so we could follow the voltage paths.
My problem exactly. Where can I purchase the regulator? Excellent video. Thanks
you can order them bout anywhere online.. just punch in the part number. I got mine from ebay..
Hey what’s up man how you doing I had the same problem I got the same TV the only difference is I get sound but it’s a flashing light no picture I want to thank you have a blessed day
Hello Sir, my sharp LC-60LE640U just has a blank screen with sound , I can see the screen get brighter when I change channels but still a blank screen, could this be the T Con board?
It would be nice that you show how to change the regulator, for next time. Thankyou.
it's really easy if you have any electronics experience.. just desolder the pins and undo the heat sink.. nothing to it.
He should not repeat the mistake again
Hi ray I know its been a while since you posted this repair, it what is the reulator part number?
If you read my comments you'll see it... I ordered from Ebay...
Great vid..where did you buy part?
I can't remember, i think Ebay I have 4 spares i'd be willing to sell.. PM if interested.
@@rays.2480 any left?
How about no power?
I have the LC-60LE660U and I can't get it to turn on. It's not showing any power
Hi I have Sharp Aquos LC70LE650U, I already change the power board what you did but still same flashing I get. Do you have any idea what else the problem is?
Same here. Just replaced the board to no avail
I feel you both nothing. Ill be ripping mine apart again to try and figure it all out.
JayR Barbosa did you fix it?
I have same problem replaced board and still same issues
Hi Mr. Ray: Thank you for sharing. I'm having the same issue. My Aquos LC-70LE640U. Can you replace the regulator if I send you the board?
i could replace the regulator, but i have no way to test the board afterwards. as i have said in previous post.. I no longer have the tv..it was a customer repair.
did you ever decide ??
Hallo there I hope u still here I also have a sharp but mine is the model LC-60LE635E
It looks really similar to the model you have, the power supply board is the same and I have the same issue, no sound and no backlight. On my tv it blinks two times maybe I'm Lucky as well and have the same problem. I'll check the the four pins and give you feedback. Thank you for the video!
good luck..
I have measured:
pin 1: 12v
Pin 2: 13v
Pin 3: 0v (ground)
Pin 4: 2.4v
So my regulator is fine.. sadly..
I didnt see you've change the regulator bro..
Just curious if you have the schematics I'm looking for a couple of diodes on a dps167 cpa ...at d7202....d7201 looking for the part number cross reference number something I could find in the United States
Sorry, I do not.. I didn't have a schematic either when I repaired my set..
hola, me puedes decir que pieza se cambio?
Donde compras las partes?
I have a sharp aquos lc-60le550u and it looks identical to this and doesn't seem to have a backlight even though the panel comes on. do you believe this is the same issue and should I go ahead and purchase the same resistor? I don't have much experience but i can go buy a solder to make it happen
For a few bucks,,, what do you have to loose ?
Hola colega
Deberías de hacer el mismo video pero en Español
Saludos desde Colima Colima México
Where can I get a new regulator ?
Y saw Sparks coming from the back of my Sharp Aquos and it went shut anybody knows what part went wrong??
Hi Ray Thank you for the video I have the same TV model and the same symptoms unfortunately we don't see how you changed the regulator in the video is it possible to make another video where we see you change it as is it possible also to confirm the technical name of this regulator so that I can buy it online otherwise if you sell it it will be cool
please read the other comments.. If you have any electronics experience, then you can do it,,it's not complicated to change out the regulator..
@@rays.2480 thank you for your answer I checked all the comments but I did not find the regulator designation please give it to me please I will look for it on eBay
Good morning Mr., please I need a measurement if you have a A6069H chip of a tv SHARP between pins 7-8 and 3, I have 5 pieces and between those pins there is zero ohms, I want to be sure of that measurement to return them. Thank you very much.
Sorry, but I posted 2 years ago that i do not have this tv any more..I cannot help you or anyone else.
@@rays.2480 ok, thanks for answering, take care
I have a similar issue with a lc55ub30u i just picked up off Facebook for free ordered all new boards for cheap off ebay I'm praying to jesus that after i replace all the boards it fixes it it's not hard to replace the leds i just don't want to have to resort to that and i truly don't think they're dead as I'm not positive but i think when i was tinkering with it they came on briefly at one point then shut off so I'm pretty sure it's power related
good luck...
@@rays.2480 im pretty confident it is the power board aswell as the leds plug into that and the power light comes on so I'm hoping the boards fix it if they don't idk whats going on i think it's unlikely that its the lcd itself or backlights but i could be wrong
Un comentario si la pantalla esta un poco quebrada en una esquina funciona o no
Nice job, but I wish you would have shown the replacement of the part.....
sorry i cannot answer any of these questions, i do not have this tv any more, it was just a repair that i showed.. there was no videos related to the issue i had, so i shared what i did.
if you have no power, then you must check all the regulators,, you must have a schematic to follow and test.
did u just happen to have an extra regulator in your pocket? and what are the steps to taking it out and putting new one in?
No, I had to order it, I got a few of them, they were cheap. I did my typical testing, found out which voltages were missing, Which happened to be my 12V regulator. Found it, Looked it up online.
I was able to use a common regulator for testing purposes. The proper regulator has an on/off control. With the common 12v regulator, the set worked fine. But you could not control the functions of the tv to turn it off. So, when it worked, I then ordered the proper regulator, installed it, and the tv was good as new.
An easy job for someone that has electronic experience. Not a job for an amateur.
@@rays.2480 i tried the VOL down, Channel up, and power button at sametime to bypass the blinking and it works, so now i have steady light, but i have no backlight now.
Sorry, I can't tell much more about the tv, as i do not have it here. it was a customer repair.
Where can I fine a Regulator
Hi can you help me with the part number the regulator
Read my comments, you will see it ..
Can you tell me what the part number is please? Or what replacement to purchase
it's a 12V regulator with remote turn on.. you can see the part number on the IC, I bought replacements from Ebay, was cheap
Thank you for this video. But I do not have this issue, my issue is I get a box saying 'Unfortunately, TIF Test is not responding or working' and "AquosTV is not working or responding". I would like more information on how to get this working or removed. It interfers with tv channels with antenna, no cable. Does anyone else have this issue? How to get this working again?
Alma you can reset it using your remote
hi i have the same tv whit the same symptoms did some power tests and i have the same as on you video by any chance you have one of those regulator ?can i buy it from you ?? i only found them from china delivery estimated February 22 thank you
I think i have a spare, I'll need to search my box, I'll get back to you soon..
Sorry for the delay, i have looked and i have 4 chips left.. Let me know how many you want.
@@rays.2480 hi can you send me 2 just in case
@@angelito1472 sure, send me a private message and we'll go from there.
@@angelito1472 did you get my replies ?
I have same TV and it stay on standby mode,it show me tv3 no picture what can I do?
i cannot say.. i do not have much experience with this tv, other than what i showed, sorry
Hi..my tv have power..but no sound, black screen..you have any solution?
sorry, no..
Is it hard to replace that part ?
It's very easy if you have good soldiering skills. Hardest part for me was removing the back cover. had to have a lot of space to remove it.
My LC60LE650U won’t turn on but flashes 1 short blink and one long blink , any ideas?
try to google the model number and the blink codes..I don't have this tv any more..
Ray S. Thanks anyways I just figured I would ask just in case you may have remembered, I have looked everywhere with no luck , guess it’s time to replace a 5 year old TV again ugh!
Y me sale la pantalla azul oscuro
Cual es el daño??
English Please...
@@rays.2480 no English,🤔
@@cobraracer1263 >> Google translate :)
@@rays.2480 wath is the damage
@@cobraracer1263 The damage was a switched 5V regulator.
I replaced the entire power board and still get the exact blink code 3-1
I Read somewhere you have to enter service mode and reset error codes, press volume - and input then connect to power while pressing buttons, wait till the tv turn on
Im having the same problem with mine, i just order a new board
Sharp LC42D
WHATS THE FIX,
Foolish man
Interested to hear your opinion?
So here’s another trick hold channel down, volume up 30 seconds the three flashing lights will go off and TV will power up
That's not true.. If the regulator I Pointed out is bad, it will not power up with that so called trick...